Connecting the gas hob and oven

How to connect a gas cooktop and oven yourself

Before selecting a recessed oven, there are certain requirements that must be followed to avoid dangerous situations:

  • No flammable or combustible materials (kitchen curtains, towels, rags, oil) should be near the oven.
  • The furniture in the immediate vicinity of the oven must be able to withstand an ambient temperature increase of 50 C.
  • It is not advisable to place an oven and cooktop near a refrigerator or freezer.
  • The oven should be located away from water sources in the kitchen.
  • An electric oven must be close to a grounded power socket, placed more than 10 cm above the ground. From the floor.

When determining where to place the oven in the kitchen and at what height, the following placement options should be considered:

Traditional placement of the oven, with the location of the cooking surface above the oven is not necessary. This option is most often used in small kitchens with few work surfaces, and has no alternative for small.

Column cabinets

This placement is usually used in a spacious kitchen where there is enough space to install additional tall cabinets.

When deciding how high to place the oven, the following points must be taken into consideration. High placement of the oven gives a number of advantages: it is easier to clean and maintain, it is safe for small children, it is easier to get the food and monitor the cooking process.

Read more: Assembling metal gutters for the roof with your own hands

Into the carcass

In a spacious kitchen with a cooktop placed in the middle, it would be logical to install the oven in the frame directly. The option is most suitable in families without small children and infrequent cooking.

In a high drawer

A very convenient place to install the oven in the edge of the cabinet. In this case, it is not possible to use the surface of the cabinet as a working area, but it is possible to install a microwave oven, various appliances and kitchen accessories.

It should be noted that this placement is quite often used in the home for medium-sized kitchens, where there is no shortage of working surfaces, but there is also no lack of. In this case it can be considered optimal.

Mounting the cabinet in different surfaces

There are two basic types of gas hoses on sale:

Gas hoses are sold in various lengths, before buying determine what length you need.

Rubber gas hoses are the easiest and cheapest, which is probably why they are the most common. But rubber hoses are poorly protected from mechanical influences, the recommended service life is 5 years.

Polymeric gas hoses in a steel braid were previously widespread, but in many cities and countries they are forbidden for use. They differ from water hoses visually by yellow stripes in the braid.

Bellows gas hose is safer and more durable than rubber gas hoses, there are mentions of service life up to 25 years. Bellows hoses are made of stainless steel, there are threaded fittings on the ends of the hose with paronite gaskets. The hose is easy to bend, can withstand pressure up to 6 atmospheres and temperature from.50 to 200 degrees C. This is the version of the choice I made.

Bellows gas hose with protective coating is a model of bellows hose, which is protected by a layer of polymer coating.

Connecting an electric stove to three-phase electricity

Read more: Outlet for the washing machine in the bathroom installation principles

To choose the place for installing a recessed with his own hands electric oven should be treated with the utmost responsibility. In this case, in addition to observing the basic rules of electrical and fire safety, it is necessary to ensure normal conditions for the work of the oven and take care that it does not interfere with the functioning of other appliances in the kitchen.

A far from complete list of recommendations is as follows:

  • curtains, towels, paper products and other flammable objects must not be in the immediate vicinity of the oven;
  • The elements of furniture in contact with the cabinet, must be able to withstand the temperature of 50 oC without damage;
  • The oven must not be installed close to a refrigerator or freezer;
  • it is desirable to install the oven as far away as possible from water sources;
  • To ensure natural air circulation, you must provide a gap of at least 90 mm from the bottom, 40-50 mm for the sides and back of the oven;
  • On the side of the place of installation at least 10 cm above the floor there must be an easily reachable grounded socket.

Size ratio when wiring the oven

Important! The socket outlet must be rated at least 40 A. If this is not the case, make a replacement. Before you build a new oven with your own hands, you should decide where to install it. The most convenient locations for ovens:

  • In a cabinet under the worktop. The hob does not need to be installed next to it. This is the best location for small kitchens with limited work surfaces;
  • Column cabinets. This option is good for spacious rooms. The niche designed for the oven can be positioned at eye level, making it easy to supervise the cooking process and keeping hot surfaces away from children;
  • To the frame. Many housewives find it convenient and natural to install the oven in the supporting structures of a cooktop standing in the center of the kitchen area;
  • In a high cabinet. In a medium-sized kitchen, it is quite possible to mount the oven in the edge cabinet of the kitchen set.

How to connect a gas cooktop

The gas hob seems to be a very simple appliance, the connection should not be very difficult. In fact, independent installation requires certain skills and knowledge of regulations. After all, all gas appliances must be installed according to certain rules to ensure safety. In this article, we will tell you how to connect the gas cooktop.

Decide on the place of installation. Ideally, the surface should be connected close to the gas mains. But if you want to make a redesign, then use a special metal corrugated hose.

In the countertop, using a jigsaw or circular saw, make a hole that should match the dimensions of the cooktop. Wipe off all dust and sawdust.

The cut can be treated with sealant, this will prevent moisture from penetrating between the countertop layers.

Glue a special foam tape around the perimeter of the recess, it is sold with the appliance. If you lost it, you can buy such a sealant in a store that sells gas equipment and boilers. Place the cooktop on top of the tape, making sure it is in full contact with the tape.

Now connect one end of the flexible hose to the mains or gas cylinder, and the other end to the inlet of the panel. It is located at the bottom of the appliance, so you will have to open the doors and remove the shelves from the corresponding cabinet.

See also  How to boil corn in a pressure cooker multicooker

Screw on the hose using fumed tape. Now turn the gas lever to the on position. Do not ignite the burners. Soap the places that were attached to the panel and the line. If there are no bubbles, then you have done everything correctly.

What to do if there is foam? If this is the case, use an adjustable wrench to turn the nut where the gas is leaking. Continue tightening until no more bubbles form. Try not to clamp them as far as possible, especially when using paronite gaskets. They can be used in place of the rubber tape.

Once you have checked that there are no leaks, you can connect the hob to the power supply, provided that an automatic ignition device is provided. To do this, install a socket near the appliance. Note that you must use a thick countertop, more than 38 mm thick, to install the hob. When installing on a thinner surface may be difficult.

Included with the panel are two types of nozzles. With a thicker opening for mains gas and a thinner opening for bottled gas. The jets for the main supply are installed by default, so if you use cylinders, replace the nozzles.

This can be done with the wrenches that come with the stove.

Keep in mind, if the surface has an electric ignition, it is not recommended to use a hose with a metal braid for the gas supply.

In the case of a short circuit can ignite the gas.

Algorithm of connection of the panel to single-phase networks

This option is possible if a three-wire cable is embedded in the wall.

Diagram for connecting the hob to a single-phase supply Source rolexforum.ru

The following steps are required to install the panel.

  • Unscrew the plate behind the panel with a screwdriver.
  • Use jumpers to connect the first, second and third terminals. Connecting a phase is done using a brown, black or white wire
  • Connect the blue shade core to the zeros. These are numbers four and five.
  • Cables for the hob are led to the protective terminal (yellow).
  • Tightening the fixing screws.
  • Need to check reliability and tightness of connections, and the functioning of the product.

A preliminary step in connecting is to check the technical condition of electrical outlets. If necessary. to carry out replacement.

See also: Directory of companies that specialize in electrical work

Connecting the gas hob and gas oven through the T-piece.

To connect the gas cooktop and gas oven. Separate shut-off devices (gas tap) are required, that is, for each device a separate tap. Usually there is only one faucet in the apartment due to the fact that previously there was no need for it, because there was only one gas stove. But in fact there is nothing to worry about, our experts can put a tee and therefore the gas taps. And the biggest plus in this connection is that there is no need for any welding in the apartment and the entire work takes only 1-2 hours, and most importantly the cost of works are many times different in price.

And the installation of a T-piece 5 700-7 550

So the cost of connecting is calculated from the cost of services: connection gas cooktop 1900 connection gas oven 1500 well and then there are communications (taps, dielectrics, hoses and tees), depending on what you need.

How to install an oven: types of appliances, connecting to the electrical system with your own hands, preparing the niche

Stove and oven are an integral part of any kitchen. But in modern apartments to replace stationary stoves come more convenient separate hobs and ovens.

Not all people know how to install the oven correctly, but the quality and safety of its work depends on it.

Built-in electric oven can easily be installed on their own, if you carefully follow all the requirements.

Built-in ovens come in two varieties: dependent and independent. The first are installed with the hob. The latter are mounted independently of it as separate devices, installed in any place.

The appliances are connected to the mains or to a gas pipe. If the electric oven can be installed with your own hands, to connect the gas one, you need to call a gas engineer. Mounting the oven can be done in two ways:

  • Under the worktop. The hob will be installed on top.
  • Above the worktop. Installation is carried out separately from the hob in a place convenient for the hostess. In this case, it is easier to monitor the oven, but to install the device will need a cabinet with a niche of suitable size.

Regardless of where the oven will be installed, in the kitchen furniture for it must be prepared a place. To meet this condition, you can first buy furniture, and then in the same showroom to pick up a suitable oven for it. You can do the opposite. buy the oven first, and then when ordering kitchen furniture specify the dimensions of the niche for its placement.

Preparing the niche

The electric oven can be installed anywhere, but it must be away from the sink. An electric socket can be positioned on the right or left-hand side of the niche at least 10 cm above the floor. It is best to use a 40 ampere power socket for the appliance.

Install the built-in oven at a distance of 5 cm from the back wall and 9-10 cm from the floor. At least 5 cm on both sides of the cabinet. This installation ensures ventilation and prevents overheating of the furniture. Failure to do so can cause a fire. The following conditions must also be provided:

How to install the electrical installation

When installing a built-in oven, safety precautions must be followed and the installation instructions followed. First the wiring must be checked and the following conditions must be met:

You must also check the grounding system, grounding wire and protective circuit breaker, which trips in case of overloads and malfunctions of the oven. The automatic shutdown must be triggered when the current exceeds a certain value. It is selected according to the model of the oven.

To ensure the safety of the oven, a powerful copper wire is used for connection. Because of the high consumption of electricity, it is better that the appliance is connected through a separate branch of wiring. For plugging into the network, you must install a special socket designed for its capacity. It is also necessary to observe the following rules of connection:

  • Do not connect the wires by twisting;
  • do not use a connection of wires made of different materials (e.g. aluminum and copper);
  • Use screw terminals for mating;
  • Connect the appliance to the switchboard through a separate circuit breaker.

After installation, the inner surface of the oven should be thoroughly rinsed, then the oven should be turned on at maximum power and fired within 30 minutes. When it cools down, wipe the inside surface with a damp cloth. The oven can then be used.

Connecting the gas oven

The gas oven can only be connected by specialists from the gas service. Since this cuts off the gas supply to the apartment, you can immediately connect the cooktop and oven.

The appliance is connected to the gas pipe in the kitchen using a special hose. The oven must be at least 1.2 m away from the gas supply.

Before switching it on, check that there are no leaks. If you notice a distinctive smell, turn off the gas and repair the leak.

When the gas connection is successfully completed, the oven is connected to the mains to work the electric ignition and lighting.

How to connect the stove to the gas

The times when steel pipes were connected to stoves in Soviet-era houses are long gone, this technology is not used even in new buildings and it has been completely superseded by flexible hoses. With their use, it became possible to move the equipment to any place within the length of the hose. this greatly simplifies the integration into the kitchen set and repair of gas stoves.

See also  How to put the pots in the oven correctly

Flexible hose can be installed by yourself without any problems in a short time, using simple safety rules and ways to check for leaks.

Gas hoses. types

Before you connect the gas stove to the pipe or cylinder, you need to choose a high-quality sealed hose, which has flexibility and high strength characteristics against external influences (the pressure in the gas line of residential houses is quite low and does not exceed 0.03 bar.).

In the construction market a wide range of products of different lengths (under the regulations it must not exceed 4 m) with a diameter of fittings 1/2″ or 3/4″ inch, sometimes in gas stoves there are non-standard threads 3/8″ inch, for connecting which sets the adapter. Structurally, the connection fittings are made in the form of two cap nuts (Mom-ma) or one of them is replaced by an external thread (Mom-pa).

Rubber. Commonly used at home inexpensive hoses, with flexibility and high strength characteristics, the service life of products reaches 10 years. During manufacturing, a fabric cord is placed inside the rubber jacket to increase stiffness and strength of the hose, usually with pressed-in elbows with union nuts or one male threaded fitting at the ends.

Available in various lengths with a standard inside diameter of 9 mm and outside diameter of 18 mm, the outer and inner cross-section of the end fittings is 1/2″ inch. Rubber hoses have the following features:

  • Have low protection against mechanical damage from sharp and cutting objects,
  • With low-quality rubber and over time, they succumb to cracking.
  • Are not resistant to sudden temperature fluctuations.
  • Have dielectric properties, which prevent stray currents from flowing.

Rubber with metal braid. This type of feeding tubes is made of vulcanized rubber or polymeric materials, to eliminate the main drawback of an ordinary rubber in the form of poor protection from sharp objects, a metal braid is used. This type of supply line by its physical parameters does not differ from the previous model and has the following properties:

  • Products look like water supply systems, with the difference that the braid has a yellow marking indicating the possibility of work in the gas line.
  • The supply line needs a dielectric adaptor to cut off stray currents during installation.
  • Hoses in the braid can withstand temperatures up to 50 ° C, their service life of about 10 years.
  • The main disadvantages include the impossibility of visual control of the rubber cover in case of damage or cracking for various reasons, so the use of this modification is not practiced abroad.

Bellows. One of the latest developments, made of stainless steel in the form of a corrugated hose, sometimes on its outer surface put a polymeric pipe sheath of PVC. Bellows liners for gas are universally approved for use in the gas supply and have the following features:

  • They are of the highest mechanical strength and are protected against all kinds of impact, including sharp and sharp-edged objects.
  • The installation of a dielectric gasket for protection against stray currents is mandatory.
  • The service life of bellows hose reaches 25 years and more.
  • The main disadvantages are the highest price of all varieties.

Connection by means of a pipe

Connecting a gas stove with a metal pipe in the household is used quite rarely. this technology is complicated, economically unprofitable and obsolete, in addition, it does not allow you to install the stove in another place. For connection, you need to make and bend the pipe of a given size, cut a thread on its ends and connect it to the pipeline and equipment with the help of couplings.

connecting, oven
  • When carrying out the work consider several options: in the first case, the supply pipe is welded to the main pipeline, and the second end is connected to the plate with a coupling from a fitting with a securing nut.
  • In another version of the couplings with locknuts are installed on the edges of the supply pipe section (it is pre-tapped on both sides), which is then screwed to the main pipeline and the outlet spigot of the stove.
connecting, oven

You can do without couplings with nuts for the implementation of demountable connection, having a welding machine. for this purpose to the two ends of the pipe welded adapter.

One of rather rare variants of connection is the use of copper pipes. in this case the billet is bent in the required way with a pipe bender and fittings with capped nuts are soldered to its ends.

Instructions for installing the equipment

Theoretically, the gas stove can be installed (locally) by the user himself/herself. Especially since every model of gas stove, purchased officially, is necessarily accompanied by the user’s manual. This document specifically describes all the nuances of installing the equipment on site.

It is quite another matter when the appliance is connected directly to the gas and electricity network. Of those on-site installation details that are mentioned in the documentation, one of the first is ensuring adequate ventilation of the room where the hybrid stove is installed.

Installing on-site hybrid appliances is the beginning of an overall effort to equip the kitchen space with the appliances in demand

Below we will consider how to choose a place for installation, taking into account the requirements, and the peculiarities of the alignment of the hybrid stove.

Requirements for installing a stove hob

This type of appliances is allowed to be placed in the gap between the elements of kitchen furniture. In this case, on one side of the stove is allowed to place a piece of furniture, the height of which is greater than the height of the gas stove. But, according to the rules, such furniture is placed at a distance from the body of the equipment at least 300 mm.

A piece of furniture placed on the other side of the appliance must be at the same height as the hob. If it is intended to install any elements of furniture over the gas hob, such installation is only possible if it does not affect the operation of the equipment.

Based on the rules, in such cases, the minimum allowable vertical indentation from the surface with burners. not less than 650 mm, and the distance to the hood. not less than 75 cm.

Configuration for built-in installation as part of kitchen furniture: 1. surface level of appliances; 2. surface levels of kitchen furniture elements; 3. minimum distance from the hood (750-800 mm); 4. minimum allowable distance to the upper piece of furniture (650 mm)

Given the same rules for installing appliances in place, certain requirements also apply to pieces of furniture, as well as walls, partitions, floors that are placed near the heating equipment.

connecting, oven

In particular, the furniture must be heat-resistant, capable of withstanding temperatures of 90°C or more. Consideration should be given to the fact that the rear area of the gas stove heats up considerably as the equipment is used.

Optional stand and alignment

Many models of gas combination stoves are supplied complete with a stand. The use of a support slightly increases the overall height (by about 5-10 cm).

The use of a stand is convenient because this piece of equipment is equipped with wheels (two wheels) and adjusting screws (two screws). There are also gas stove designs with four adjusting screws.

Illustrative example with the adjusting support screws included in the construction of household hybrid appliances. These components make it easy and straightforward to level the appliance

If it is convenient to move the appliances with the help of wheels, by adjusting the screws the gas stove is easily aligned with the horizon or with the level of the surfaces of the furniture set.

How to install a gas hob (tutorial for trainee gas engineers)

Meanwhile, the stand, if necessary, can be removed. In this case, the adjusting screws are installed directly on the bottom of the gas stove.

Installation of a gas oven: Safety standards and requirements for its connection

Natural gas is a dangerous substance, because its leaks often end in fires, explosions, injuries, and deaths. This is why it is recommended that the gas oven is installed and connected by experienced specialists who are trained in the relevant safety regulations.

See also  Boiler 16 kW for what area

The basic requirements for the installation of the oven we have discussed in this article. In addition, we have described in detail the process of connecting the gas oven to the home gas line. Here are also tips from experienced professionals, which will allow you to do everything correctly. Thanks to this, you can safely use the gas oven.

Safety first

Gas leakage is a very dangerous situation, because it often leads to a fire, explosion, severe poisoning and death of people. The causes of these accidents are trivial mistakes that inexperienced craftsmen make when connecting a household gas appliance. In addition, it happens due to violations of the rules of operation of the oven.

In general, safety requirements are reduced to the fact that all points of connection of gas pipes with household equipment must be airtight, and the number of these nodes should be kept to a minimum. Having studied the rules of installation of gas appliances, any home handyman can cope with this task.

The most important thing is to do everything according to the instructions that come with the gas equipment. After completing the connection it is necessary to check the tightness of all joints. By following all these rules, you can achieve the desired result. to correctly place and connect the oven to the indoor gas line.

When independently installing a gas oven, a common mistake is to cut into the pipe, to which the stove is already connected.

Beginner craftsmen think that if it works well in the water supply, then for the domestic gas pipeline tee will do. Because of his installation we get 3 connections, which require high-quality sealing.

According to the rules of connecting the oven and stove to the gas pipeline, it is necessary to allocate for them a separate branch. This will result in only 2 connections, so the likelihood of leaks is greatly reduced.

T-piece installation can also be safe if properly sealed threaded joints. But it is forbidden by the current rules for connecting a gas oven. Accordingly, if in the course of the next inspection of the gas equipment specialist of the gas service will see this tee, then you will be written out a large fine.

Therefore it is necessary to get acquainted with this point beforehand in order to perform everything correctly. It is also necessary to put a dielectric gasket and a shutoff valve on each inlet pipe.

The process of installation and connection

Ovens can be dependent (combined with the hob with a single control panel) and independent. The former are placed under the stove, while the latter are allowed to be placed almost anywhere. The most important thing is that the room has good ventilation.

connecting, oven

The process of connecting all types of ovens is the same, so here are general instructions.

  • Select and prepare the place for installation;
  • connect the oven to the home power grid;
  • Connect it to the gas supply line inside the house;
  • Place the oven in a niche or a cabinet;
  • check the tightness of all connections;
  • Test the oven’s operation.

Before installing the built-in oven, you must unpack it and check for any damage that may have occurred as a result of careless transport. In addition, it also allows you to identify a factory defect.

Then study the manufacturer’s data sheet. In it you will find detailed instructions for installation and operation of the oven. In addition, there are ways to fix the most common malfunctions. Thanks to this, you can fix minor malfunctions yourself and protect yourself from additional costs, because you don’t have to call a technician and pay him for his work.

For quality ventilation of the outer walls of the oven is required to provide such gaps:

As practice shows, these dimensions are often not respected. If the manufacturer has implemented in the appliance blowing the walls, then for a ventilation gap can not worry.

The rear part of the furniture niche before installation is removed or holes are made in it for supplying communications required for normal operation of the oven.

The material of furniture must be able to withstand up to 120 ° C. After unpacking the unit, you must install it near the connection point. For example, you can put it on bars. This will make it easier to perform the required manipulations.

If electricity is required

Modern models of gas ovens include a large number of additional functions. They allow you to expand the capabilities of equipment and more comfortable to use it.

Electricity is required to use these functions. To connect this device to the fuse box use a three-wire cable, RCD 16A (for units with a capacity greater than 3.5 kW. at 32 A, but this figure is mainly calculated for electric ovens) and grounding.

  • In the kitchens of new apartments there is a grounded socket for connecting the electric stove, so you can use it to connect the oven as well.
  • Often connect the cable to the oven with your own hands, so before connecting you need to first disconnect the electricity and prepare a tool with insulation.
  • The connection procedure itself consists of the following steps:
  • Opening the junction box (placed at the back of the device).
  • The screws that clamp the terminals are loosened.
  • Then the cores of the power cable are run in the terminals.
  • Then the cable cores are clamped with the terminals.
  • Then close the lid of the box.

How to connect a gas oven?

Any activities related to the installation of gas equipment should be carried out by specialists with the appropriate approvals. This rule has not changed in any way. Doing these things yourself is a high risk of being fined for unauthorized connection of gas equipment (oven).

But if we characterize the procedure itself, the following stages stand out:

  • Connecting the equipment to electricity;
  • connection to the gas supply system;
  • The installation of the gas cabinet in the kitchen set;
  • checking for gas leaks, testing of operating systems;
  • Commissioning and granting permits.

During installation, you must take into account a number of requirements:

  • The installation of the oven takes place in rooms with good ventilation, equipped with a hood;
  • the room must have access to power supply systems, equipped with special outlets with grounding;
  • Always take into account the features of a particular model, its technical characteristics;
  • Furniture adjacent to the oven must be able to withstand a heating temperature of at least 120 ° C.

Check for gas leaks

About this we have already written above that these works should be carried out by the corresponding experts. You can always call the contact numbers and call a master for the connection and installation of the gas oven. We have a free departure of the master within the Moscow Ring Road.

But if you have decided after all the installation activities to make sure that the technique is properly installed again, there is a simple folk method that allows you to check for gas leaks. For this purpose:

  • You need to take a hairbrush (the one you used to shave);
  • apply soapy foam to the hoses and all connections with it;
  • Where there will be foaming soap, it means there is a gas leak in the apartment, house or room.

At the end of all work, the work of all systems, control panel, check whether all the internal and external films, shipping tapes are removed. The gas oven is turned on and ignited.

If you appeal to GasTechMontage, we provide a warranty on all kinds of work, plus permits. Get a free consultation by phone: 7 (977)-600-56-56 (open seven days a week, from 8.00 to 23.00).

| Denial of responsibility | Contacts |RSS