Error oe in a DAEWOO washing machine

Don’t get excited before you know it! It may not be that serious, and you can fix the OE error yourself. Here are the cases where it can be done.

  • The drain filter is clogged. It keeps the washer pump from getting large debris from things in it. The filter is usually located on the front side in the lower right or left corner behind the hatch. Unscrew it, remove the debris and screw it back in. From now on, do this regularly. Instructions for removing and cleaning the filter are in the user manual of your LG machine. Look through the filter opening into the drain pump as well. It is possible that a small object got into the impeller and blocked its rotation, so the drain does not work, and the LG machine shows error OE.
  • The drain hose is trapped or kinked. Carefully inspect the hose along its entire length. Straighten it out if you find any bends or remove any objects that have jammed it.
  • Clogged drain. This often happens when the washing machine drain is connected to the sink siphon. The siphon becomes clogged, and the clog prevents the passage of water from the machine. Diagnosing a clog in the drain is quite simple. Pull the end of the drain hose out of the drain, put it in any container (bucket, basin, tub, toilet) and turn on the drain program. If the water will drain normally, then there is nothing wrong with the machine, and the cause of the error is a clogged drain. To fix the problem it is necessary to clean it.
  • There is a malfunction in the control box. Unplug the LG washing machine for 10-15 minutes and then plug it in again. It may help to reset the error OE.

If the above items do not work, it means that there is some kind of breakdown, and you need the help of a master.

The drain pump or its wiring and contacts could be defective. The drain pump filter or drain hose could also be clogged. The hose could also be incorrectly connected or pinched.

IE. the water doesn’t fill the washer tank or it does, but very slowly.

This error does not necessarily mean the machine is broken. It is possible that you simply forgot to turn the water tap on the water supply pipe to the open position. Therefore, first of all, make sure that it is open. It is also possible that for some reason there is no water in the water supply system or there is water, but the pressure is very weak. To check for this problem, simply turn on the water in the faucet. If there is no water or it hardly flows when the valve is open, then you have found the cause of this error. You can call the utility company and clarify when the failure of the plumbing will be repaired.

Next, you need to check the strainer-filter on the fill valve. If it is clogged with rust or anything else, it can prevent filling the tank with water. To check we need to close the water tap and unscrew the drain hose from the side of the washing machine. It is at the junction of the hose and the machine and the strainer-filter is located. If you notice that it is clogged, then you need to clean it carefully. There is also a chance that the filler valve itself is broken. Or the pressostat (level sensor).

UE The balance in the tank is out of balance.

When you can see this error code on the washing machine display?

The laundry is clumped together. It is disturbing the balance of the tank. In this case you need to stop the wash, open the door and distribute the items to be washed evenly. The error code can also be caused by improper installation of the washer-dryer or non-adjusted feet. Check that the appliance is stable and level. If the appliance wobbles when pushed lightly, then you need to adjust the feet or level the place of installation.

LE The door of the washing machine is not securely closed or the LCR (door locking device) is defective.

What are the possible reasons for this error?

This error code is displayed when the lock has not locked the door in a closed position. This can occur if it is simply not closed tightly or if it is warped. The door lock and the hatch locking device may be defective. If the DEB is broken, it needs to be replaced.

E8. The water level sensor is broken

Probably the load sensor is defective. In order to fix the situation, you need to change it.

E9 Pressostat breakage (water level sensor / water level switch).

Check the pressostat tubes and the tightness of its connections. If the tubes are fine, it is most likely that the water level sensor itself is broken. If this is the case, it needs to be replaced.

H6. The electric circuit is broken.

First, make sure the heating element (TEN) wiring is okay. If heating element itself is broken you need to replace it.

Interesting:

Guys SOS. Yesterday bought a washing machine DAEWOO Electronics DWC-UD121s. Today it was connected. Started washing. After half an hour it beeped and the display showed b3 or 63 instead of the time. It doesn’t wash any further. What to do? SOS

This combination comes on for about 30 minutes when ironing is in progress

The double screen on the back of the machine lights up on the number 1.8. What to do?

In DAEWOO front-loading washers the filter on the drain is clogged, because of this clogging it starts to shake, and from the vibration pops out the terminal shut-off sensor. LE Code. We say THANK YOU.

Thank you! Tired of it I did not know what to do now I wish I could find how to clean it =)

Daewoo washing machine error display “OE”

Suck! The washing machine works, but the time does not go. How to solve the problem?

Hello. Changed the bearing and oil seal. I assembled it and turned it on. Gives out this P_t. What is it??

After changing the bearing, gives me error P_t or P_e I do not know. What It May Be?

On my DAEWOO washing machine the display shows What it means, but the machine stops. After resetting the countdown starts all over again and after a couple of minutes, it shuts off.

We found out what the problem is? I have the same one.

Good afternoon, my machine DAEWOO 12 kg gives out error E6. There is no such a code for this brand, help me to solve the problem.

Hello, my DWD-UD 2413K has error E6. I can’t find the deciphering code.

In this case it is convenient that all models have almost the same diagnostic system. So you don’t have to look up the deciphering for a particular unit.

As for the LE error, the causes are directly related to problems with the hatch door. Check if you are closing it tightly. To do this, push and press the door well, you can even put your knee, but without fanaticism. If after this action, the code disappeared from the display and the washing process started, then the locking mechanism is broken. Replace or clean it from dirt. If pushing on the door does not have a result, the problem is most likely with the locking device. The door closes, but in fact, for the “brains” of the machine, remains open, which prevents the start of washing.

As a result, the LE error. As for repair with your own hands, it is a waste of time with UBL. It is easier to buy a new part and install.

Maybe the drain pump (pump) or its wiring and contacts are broken. The drain pump filter or the outlets and the drain hose could also be clogged. In addition, the hose may not be properly connected or clamped.

IE. water is not poured into the washer tank, or is poured, but very slowly.

This error does not necessarily mean that the machine is broken. It is possible that you simply forgot to turn the water inlet valve on the water supply pipe to the open position. Therefore, first of all, make sure that it is open. It is also possible that for some reason there is no water in the water supply system or there is water, but the pressure is very weak. In order to check if this problem exists, simply turn on the water in the faucet. If there is no water or barely any water flow when the valve is open, then you have found the cause of this error. You can call the housing and utilities department to find out when the plumbing problem will be solved.

Next you need to check the strainer-filter of the fill valve. If it clogs with rust or anything else, it can prevent filling the tank with water. To check we will need to close the water supply tap and unscrew the drain hose from the side of the washing machine. It is at the junction of the hose with the machine and is the seat-filter. If you notice that it is clogged, then you need to clean it carefully. It is also possible that the filling valve itself is broken. Or pressostat (level sensor).

UE The balance in the tank is out of balance.

In which cases you can see this error code on the washing machine display?

The laundry is piled up. It disturbs the balance of the tank. In this case, you need to stop the washing, open the hatch and evenly distribute the washed items. If you have noticed that the washer is clogged with rust or something else, it is blocking the water in the tank. Make sure the machine is stable and level. If it wobbles when pushed lightly, then you need to adjust the feet or level the place of installation or choose another one.

LE The door of the washing machine is not securely closed or the UBL (Door Locking Device) is defective.

What are the causes of this error?

This error code is displayed when the door lock has not latched the appliance door in a closed position. This can happen if it is not closed properly or if it is warped. Door lock and shut-off device may also be defective. If the UBL is broken, it must be replaced.

E8 The load cell is broken

The load sensor may be defective. You need to change it in order to correct the situation.

E9 Pressostat (water level sensor/water level switch) defective.

Check pressostat tubes and tightness of connections. If the tubes are fine, then it is most likely that the water level sensor itself is out of order. In this case, it must be replaced by.

H6. Electrical circuit interrupted.

First make sure that the heating element (TEN) wiring is okay. If the heating element itself is broken, it needs to be replaced.

Interesting:

SOS Guys. Yesterday I bought a washing machine DAEWOO Electronics DWC-UD121s. Plugged in today. Started the wash. After half an hour it beeped and the display showed b3 or 63 instead of time. Doesn’t erase any further. What to do? SOS

When ironing the laundry for about 30 minutes, this combination comes on

The machine is lit on a double screen on the far side of the number 1.8. What to do?

In washing machines DAEWOO with front loading clogs the filter on the drain, this clogging it starts to shake, and already from vibration pops out the terminal lock sensor. LE code. We say THANK YOU.

Thanks! I don’t know what to do and now I need to find a way to clean it =)

Suck! The washing machine works, but the time does not go. How to solve the problem?

Hello. Changed the bearing and oil seal. I assembled it and turned it on. Gives out this P_t. What is it??

After replacing the bearing, P_t or P_e error. What it may be?

DAEWOO washing machine display shows What it means, but the machine stops. After resetting the countdown starts all over again and in a couple of minutes it switches off.

Found out what the problem is? I have the same one.

Good afternoon I have a machine DAEWOO 12 kg gives out error E6. No such code for this brand, help me solve the problem.

Hello, DWD-UD 2413K gives out error E6. I can’t find the decryption code.

Error codes of washing machines DAEWOO

Washing machines DAEWOO can not be called the market leaders, but a certain percentage of consumers still give preference to this manufacturer. Reliable enough equipment is produced under the brand name, but it is not insured against breakage. But it implements a self-diagnostic system, which notifies the user of faults. Knowing the error codes of DAEWOO washing machines, we can detect the problem and repair the machine properly in no time.

Codes of errors of washing machines DAEWOO are designated by figures and Latin letters, and they are shown on displays, which show washing time. As soon as the self-diagnostic system registers the appearance of any malfunction, the error code appears on the display. It is possible to decode codes by reading the booklet that comes with the machine or by using our review.

We have put all codes for DAEWOO washing machines in table. It not only reveals the nature of the malfunction, but also gives you information about how to correct it. The errors themselves are not so many, so it takes 1-2 minutes at most to diagnose a breakdown. As for repair work, its duration depends on the skill level of the user or repairman.

  • Check the drain pump and its electrical circuits;
  • Drainage system permeability is checked;
  • It is necessary to check the condition of the filter and perform its cleaning from foreign objects.
  • Check the faucet at the machine’s inlet. it is possible that it was closed;
  • Check the water pressure in the water supply line. If necessary, increase the pressure;
  • The machine inlet strainer should be checked;
  • The solenoid valve must be tested and the electrical circuits checked;
  • The pressostat is checked.
  • If this error occurs, the laundry should be redistributed manually, since it may be crumpled, which causes strong imbalance in the tank;
  • The position of the washer-dryer must be checked and adjusted at the installation site.
  • Check the condition of the door and close it tightly;
  • The serviceability of the door lock should be checked.

Thus, we can fix many malfunctions on our own. And only in some cases that require specialist intervention, you need to contact the service center. Also in the table of error codes of washing machines DAEWOO the need to check the controller. the board that controls the whole washing machine is not specified. Some errors can also be its fault. The same situation is with errors in Whirlpool washing machines.

The controller can be checked only in conditions of service center, because special equipment is required for diagnostics of electronics. In some cases the boards are subject to repair, and in other cases they are simply replaced. On our site you can also find error codes of washing machines Elgi.

Error E8 in the washing machine DAEWOO

If your DAEWOO washing machine gives out “Error E8” on display, then it is a serious diagnostic. Troubleshooting is complicated by the fact that a similar code can lead to several elements of the system, from the tachogenerator and motor to the control board. To localize the problem, it is necessary to consistently check all possible “culprits”. it is difficult to make it without the help of professional masters, but it is possible if to be guided by our instructions.

Let’s test the elements of control board

So, you have decided to repair the control board yourself. Then it is necessary to figure out on your own, what element on the module, responsible for the motor functioning, has failed. In order not to guess and not to experiment it is better to facilitate yourself with the circuit diagram of the electronic block. It is usually found in the factory instructions of the washing machine.

Mechanical damage to the board, burned out contacts and disconnected electrodes can be seen with the naked eye.

Next disassemble the upper part of the machine and carefully remove the board. Before you start testing with a multimeter, inspect the module from both sides, trying to see obvious scratches, chips, loose contacts, burned out tracks or broken electrodes. If there is such damage, there is no need for comprehensive diagnostics. you just need to eliminate the detected trouble. When everything is visually all right, it is worth checking a number of board elements one by one.

  • Capacitor. It is not uncommon for a blown capacitor to cause error E8. In blocks of washing machines, it acts as a stabilizer, and takes the hit from power surges. To repair a burned out element is impossible, you have to dismantle the “box”, pick up a similar one and solder with a lamp in the vacated place. If you additionally install filters, you can reduce the risk of repeated fires. But keep in mind that the capacitor is connected to the board only to the positive electrode, and a multimeter is used to check the circuit resistance.
  • Resistors. The most common cause of board burnout are sensitive resistors. To correct the situation, it is necessary to test the module by measuring the resistance with a multimeter. First, the probes are connected to the first line, where the value should approach 8 ohms, and the overload indicator is less than 2A. Next, the second line is evaluated, where the overload is limited to 3-5A. The final resistance depends on the block frequency, for example, in a simple circuit the parameter will not exceed 10 ohms. If there are deviations from the norm, it is necessary to resolder the elements. Also professionals recommend replacing and filters.
  • Thyristor unit. It fails if the mains has been overloaded beyond 220W or impulsive interference has occurred. In that case it will be difficult to repair with your own hands, but it is quite realistic. First we measure the negative resistance of the board, which on the first order diodes must not exceed the 20V mark. Output contacts burn out rarely, but they also need to be checked. Take a tester, strip the cathode and estimate the values. When the average value fluctuates within 12V, the test is passed, but otherwise. change the faulty filter. Purchase a new element and solder through the positive contact to the thyristor unit. The main thing is to monitor the condition of the flimsy but expensive ports, and upon completion of the work carefully clean the module.
  • Trigger. Failure due to capacitor failure. Diagnosis is made with a multimeter, which is connected to the output contacts and a nearby filter. If the first reading on the tester is about 12V and the second is about 20V, then everything is fine. Otherwise it has to be repaired, which takes a lot of time. First solder the output valves, then mount a new trigger, measure the threshold voltage and resistance on the modulator. The main thing is to be careful with the capacitor cathode (it is easy to hit and damage it when soldering the “neighbor”).

These are the main “weak points” on the control board, which can cause the fault code E8 to light up. It is possible to check and repair them yourself, but only with experience and practical knowledge. If module diagnostics didn’t help to detect a problem, then we pay attention to the motor and tachogenerator.

Typical breakdowns

Taking into consideration the above-mentioned main errors you get an opportunity to detect the most problematic parts of DAEWOO washing machine. As a rule, users of such devices turn for help to service centers with the following breakdowns:

The listed breakdowns are considered typical, and there is no difference what type of washing machine you operate. with vertical or horizontal loading. Among the problematic areas, experts identify the drum of the DAEWOO, which over time wears out and begins to rust.

Inlet valve, filter element, pump

The symptom of a defective electromagnetic valve cannot be confused with any other DAEWOO washing machine malfunction. If the inlet diaphragm does not work properly, water will either not flow into the tank or, conversely, will pour into the system by gravity, even when the dispenser is unplugged.

If you notice the “murmur” of water intake and drain, when the washer is off. urgently check the inlet valve.

You must first remove the top panel of the machine DAEWOO, unscrewing the two screws that hold the cover. The solenoid valve is located where the inlet hose is connected to the body of the washing machine. Next you need to check the valve gaskets. If they are not deformed, test the part with a multimeter. If the resistance on the contacts of the intake sensor will be in the range of 30-50 ohms, it means that it is serviceable. Finding that the intake valve is broken, you should replace it, the element can not be repaired. It is necessary to buy a detail, unscrew the faulty sensor from the machine and put a new one, connecting all the pipes and wires.

If you noticed that the washing machine DAEWOO does not empty the water, and you do not hear a sound characteristic of a working pump, you should check the pump. To get access to the part, you will have to lay the washing machine on its side and remove the element through the bottom. Next, you need to inspect the pump impeller, remove hair and other debris from the part. After disassembling the body of the element. all the dirt is cleaned from the inside. The pump should also be tested with a multimeter to rule out “burning out” of the node.

All of the above “symptoms” may be the result of problems with the electronic unit. If the simistors or tracks on the board are damaged, the washing machine will not work. Diagnostics and repair of the control module should be entrusted to professionals. Digging into the “brain” of the machine with your own hands is dangerous. you can further damage the technique.

DAEWOO Washing Machine: Trouble Codes

Washing machines of this trademark are not the most popular in Russia. But the manufacturer offers a special model range, which you will not find at other brands. These are compact wall-mounted machines.

There are also standard models with front loading. However, all of them are subject to breakdowns.

What to do if the automatic gas cooker gives out an error? Before proceeding to repair, rule out a failure in the system. For example, the machine was washing properly, but suddenly the electricity was cut off.

The trouble code (OE, IE, UE, LE, E8, E9, H6) is displayed after switching on. Then perform an error reset:

If the code no longer appears, continue washing in the proper order. But if the error appears again, don’t ignore the message. This can lead to more serious problems. Deciphering you will find in the table.

Sometimes the line pressure drops. Wait for supply to be restored.

Masters of service centers note frequent malfunctions of washing machines DAEWOO:

Among the faults can be listed minor problems that users sooner or later encounter. This is a clogged drain and fill line, leaky connections of hoses and nozzles. The sunroof cuff also suffers. With improper maintenance, it is covered with mold and mildew.

Take care of your appliances, do not allow the units to wear out. Clean the filters from debris in a timely manner, connect the appliance only to a moisture-resistant and grounded socket. Then the machine will last the promised years, maybe even longer.

Though DAEWOO machines are not the most popular in the market, they are on sale and in many cases are bought by our compatriots. These machines are very reliable, but they break, as well as machines from other brands. Thanks to the self-diagnostic system, the consumer can find out if the appliance is faulty, and what to do.

Most often the owners of DAEWOO machines turn to masters for washing machine repair for the following reasons:

Many people are interested in the wall-mounted models of washing machines DAEWOO. The process of washing you can see in the video Vasily Tolkachev. To prevent malfunctions, it’s worth doing a few simple measures that will make your life easier and extend the life of your washing machine. Detailed information about them is told in the Ukrainian program “Everything will be good”.

| Denial of responsibility | Contacts |RSS