Homemade bottom vacuum cleaner for the pool

Self-made vacuum cleaner for the pool. design features

A small artificial pond is cleaned by hand. Easy to drain and clean the walls and bottom. However, with a large pool area, cleaning turns into a time-consuming and labor-intensive procedure. Handmade pool vacuum cleaner makes the job a lot easier.

Contamination of the artificial pond is inevitable. The wind blows debris and fine dust, and leaves, flowers, and twigs fall from trees and shrubs into the water. Bathers leave hair, cosmetics, skin flakes in the water. Micro-particles gradually settle on the bottom and walls of the pool, forming a thick, water-insoluble dirty film.

It looks unattractive and causes blooming of water, growth of harmful bacteria. Periodically, the pond bowl must be emptied of accumulated dirt. It is better to use a special device. a water vacuum cleaner.

The filter in the supply pipe does not protect the water from dirt from the air.

Why do we need a water vacuum cleaner for the pool?

The water in both indoor and outdoor pools becomes contaminated over time. While coarse debris is easy to remove with a net, dust and sand cannot. Contaminants make the water turbid and sink to the bottom and walls of the basin. It is impossible to drain often tons of water in order to wash the bowl from the dirt. This is where a water vacuum cleaner comes to the rescue. The unit helps to clean the dirt accumulation without draining the water from the pool.

Special nozzles are easy to use on smooth and relief surfaces. In addition to the bottom and walls, the vacuum cleaner cleans the pool steps. The device copes well with mold in case of blooming water.

Why you need a water cleaner for your pool

Not only in indoor pools, but also in outdoor ones, the water gets dirty with time. While large debris is easy to catch with a net, dust and sand are impossible to remove. Contaminants make the water look muddy and sink to the bottom and walls of the basin. Often it is impossible to drain tons of water to wash the bowl from the dirt. That’s where the wet vac comes in. The unit helps to clean dirt accumulation without draining the pool water.

Special nozzles are convenient to use on flat and uneven surfaces. In addition to the bottom and walls, the vacuum cleaner also cleans the pool steps. The device copes well with mold in the case of water blooms.

home made pool vacuum

How to assemble a vacuum cleaner for the pool with your own hands

The principle of the device is that a person brushes the surface of the pool (the smooth surface of the water, walls, bottom, steps), and the automatic device absorbs all the dirt and plaque. Dirty water passes through a hose to the pump, where it is cleaned with filters. The filter can be one or more, and in heavily polluted artificial reservoirs use several filters per treatment. Seems costly? Then calculate the number of cubes of water, which will have to be poured every two weeks, in order not to turn the place for bathing in the frog. And to cope with yellow-brown plaque can be only by washing all surfaces with chemicals. After them to say whether the pool is safe for bathing children, can only be an expert.

That’s why making a handmade device has become almost a cult for private citizens. No special skill and technical skills are required.

Choosing materials for making a vacuum cleaner

First, we determine what our bottom vacuum cleaner nozzle will be made of. There are several variants of making a brush:

The first option may well be used if there is no reference to the duration of the cleaning process. But the second one speeds up the cleaning process, but requires some time for installation.

homemade, bottom, vacuum, cleaner, pool

For independent manufacturing nozzle will be required a piece of polypropylene pipe in 25-30 cm, sawn into two parts and a slot of 4 mm. Then these parts are inserted into the n. п. plumbing tee and solder. The remaining slot serves as a place for the pipe that connects the hose to the pump with the brush.

An important question is the safety of use. Therefore plugs are necessarily placed on the slots, leveling the possibility of damage to the surface. All sharp edges are treated with an emery, file.

For better efficiency of such unit it is possible to improve it with improvised materials, attaching the narrow strip-brush on self-tapping screws or glueing a rubber band from the car wiper. The glue is of high quality, so that in contact with water the structure will not disintegrate.

The question of how to connect a vacuum cleaner for your own hands solved by the usual plunger or rubber adapter for the drain, which are mounted to a water intake of corrugated hose for traps. For convenience of the p. п. You can also make a handle.

How often should I clean the pool

To ensure that the cleaning process was effective and non-labor intensive, experts recommend that it be carried out at least once a week, starting with the walls, then proceeding to the water surface and the waterline and the bottom. Less fouling of those pools that are covered at night. And after each drain it is not superfluous to go through with a stiff brush on the surfaces using nonaggressive detergents.

Vacuum cleaner for cleaning your own hands. a guarantee of health of all family members, a pleasant pastime and aesthetics of the reservoir.

homemade, bottom, vacuum, cleaner, pool

Vacuum cleaner for the pool with their own hands: an annotation on making

Creating an aqua vacuum cleaner for your own hands everyone can do and will not take much time. All the necessary materials for its production can be purchased at any plumbing store:

  • Polypropylene pipe;
  • Sealing rubber bands;
  • Corrugated hose;
  • A brush or other element to serve as a suction nozzle.

The description of the process assumes that the normal pump is already available. The choice of the cross section of the hose, pipe and gasket is based on the size of the filtered water supply pipe.

Tip. Do not save on the length of the corrugated hose, otherwise the pool will not be comfortable to clean.

Creating a brush to clean the pool

Consider a few options for the manufacture of intake nozzle.

Connecting an ordinary brush from a household vacuum cleaner to the water intake hose. It is better to pick up a brush designed for cleaning furniture. it is a small flat with a narrow slit.

Making a cleaning brush from a polypropylene pipe. To work we need: Tee, n / p pipe, caps, angle grinder and soldering iron. Order of assembling a homemade brush:

  • From the pipe to cut 25-30 cm.
  • Along the cut you need to make a 3-5 mm wide incision.
  • Pipe cut in half and both pieces stuck in a polypropylene tee used in plumbing work for distributing.
  • Install a piece of polypropylene pipe in the third hole of the connecting tee. This section will serve as an adapter between the brush and the pump hose.
  • Plug the cutoffs of the first pipe (with slots) on each side with plumbing plugs. Homemade brush is ready to install.

Made on the second variant of a brush can be a couple of upgrades. Enough to attach a not wide bristly strip or a rubber band from the car wipers to the tube with a slit. A minor improvement will increase cleaning efficiency. The suggested parts can be exchanged with foam rubber strips or other elements. it is only a matter of creative ingenuity and ingenuity.

Connecting self-made vacuum cleaner for the pool with your own hands

The next step is to connect the brush. For the normal operation of the aqua vacuum cleaner, the main condition must be the tight connection of all parts.

We need a transparent corrugated hose installed on the siphons under sinks and sinks. Fasten the corrugator to the place of water intake from the pool. Connection is made by means of the appropriate size sewer adapter. The rubber band should perfectly cover a hose and adjoin to water intake.

An indispensable detail of an aqua vacuum cleaner is a handle. Its function can do polypropylene pipe length of about 2 meters (depending on human height and the size of the pool).

Vacuum cleaner for a frame swimming pool with your own hands ready to use. Self-made device will be suitable for cleaning and other types of small pools (inflatable, plastic bowls, etc.).).

homemade, bottom, vacuum, cleaner, pool

To reduce water overshoot, it can be passed through the filter and later be pumped back to the reservoir. At the end of the hose connected to the outlet, you must install a filter or replace it with another catching device. In plumbing stores sell a huge number of special filter bags that hold huge and small particles of dirt, but allow the water flow.

Tip. The water in the pool should not stagnate. On this basis, it is advisable to fill the bowl with the latest water. But to reduce consumption, pool cleaning with a water change can be switched with cleaning without changing.

How to make a pool vacuum cleaner with your own hands

It is important to determine what work will perform the device. Water intake can be obtained through a funnel floating on the surface, into which debris is drawn and filtered through a sieve. Such a device for cleaning the water mirror is called a skimmer. A homemade pool vacuum cleaner. based on a sump pump, can be used to remove sediments from the bottom and walls with a reinforced device. brush, scraper, normal sucker. An example of such a vacuum cleaner for the pool from a deep-well pump Rucheek shown in the video.

Filtration of water in the pool can be carried out with the lifting of water into the filter installed on the surface. For this purpose it is necessary to break a circulating line for a trimmer of the pump and to build in the filter, on an intake or a discharge. All filters are installed outside the pool for easy maintenance.

Making a water vacuum cleaner for cleaning your own hands. a fascinating process. It is important to choose the type of filtering material. It is necessary to assemble a scheme of construction, providing for the withdrawal of purified water and a system of washing the filter from sediments. So the sand filter lime over time, requires chemical treatment, diatom is washed with a countercurrent of water, and the cartridge is removed for cleaning or replacement. Here you can see how to make a sand filter to the pool vacuum cleaner from a plastic barrel on video.

Designed for the Moscow region, where the water contains a lot of iron impurities, it must be clarified by repeatedly running it through a sand filter.

How to make a vacuum cleaner for the pool by yourself

Although handheld water vacuum cleaners are cheaper than others, the are still high, so some craftsmen have learned to make such devices at home from improvised means.

Making a vacuum cleaner out of a plastic pipe for water supply

You will need: plunger, corrugated hose 2-3 meters, plastic pipe 1.5-2 meters, 2 plugs, plunger, rubber seals or clamps.

Tools: soldering iron for plastic pipes, angle grinder, file, knife, screwdriver.

homemade, bottom, vacuum, cleaner, pool
  • Cut off two pieces of 10-15 cm from the pipe.
  • Solder them into a tee to make a straight line.
  • Along the length of the resulting structure to make a 3-5 mm wide incision and seal the corners of the cut.
  • On the edges of the sawn pipe you need to solder caps.
  • Solder the rest of the plastic pipe to the perpendicular hole of the tee.
  • A corrugated hose is put on the edge of the long pipe and fixed with rubber seals or clamp.
  • It is necessary to cut a through hole in the middle of the plunger and fasten the plunger to the second end of the corrugated hose.

That’s it, the device is ready. It is enough to attach the plunger to the suction opening of the filter-pump and you can use it.

How to make a bottom vacuum cleaner from improvised means

You will need: a cloth that is well water permeable (tulle, gauze, etc.), 100 mm sleeve with rubber seals on both sides, 3 pieces of adapter from 100 to 50 mm, 45 degree angle, corrugated hose 2-3 meters, a piece of plastic pipe 50 mm long 15-20 cm, clamps, a piece of linoleum, foam rubber and some screws.

Important! All metal parts must be hidden with cloth, insulation tape or polyethylene. Otherwise they can scratch the surface of the pool, and if it is inflatable, you can even tear the outer casing.

Tools: Drill, angle grinder or hacksaw, needle and thread.

  • Adapter with 100 mm side cut at a slight angle. Drill holes for bolts, to the cut edge of the adapter with bolts to attach foam and linoleum so that they protrude beyond the edge of the adapter for 1.2 cm. Cut the linoleum so that its protruding edge resembles a brush.
  • Insert a 50 mm piece of pipe into the adapter-brush and connect the adapter to it
  • From the cloth in 2-3 layers to sew a small bag (to fit into the sleeve), with a sealing rubber band to fix it in the sleeve.
  • Connect the socket with a bag to the adapter. and on its other side install the adapter
  • Connect the adapter angle of 45 degrees. Attach a corrugated hose to it and connect the hose to the suction hose of the pump. filter.

That’s it, the vacuum cleaner is ready to use. Instead of improvised brushes, you can use the cheek for furniture with a household vacuum cleaner.

Vacuuming Intex pool using the siphoning method.

Conclusion

With such simple details cleaner for the pool with his hands ready. Self-made vacuum cleaner is a great budget option for a small pool.

Cleaning the walls and bottom with a homemade vacuum cleaner is necessary several times a week. And thoroughly passes all parts of the walls and bottom of the pool, otherwise the water will quickly fade and will be unsuitable for swimming. Homemade vacuum cleaner is quite capable of such a task. In addition, a handheld vacuum cleaner is very handy to clean hard-to-reach areas and pool walls. Some robot vacuum cleaner models can not perform this function. And this is clearly a big plus small helper. For a good result, a sufficient pump capacity of more than 9000 liters per hour will be a major requirement.

| Denial of responsibility | Contacts |RSS