How to assemble a dryer on a magnet battery. How to make a dryer yourself

Www ldntver ru of dryers how to install

Liana ceiling dryer is an excellent alternative to outdated ropes for hanging underwear after washing. This practical product will become an indispensable element in the everyday life of every housewife.

The design of a modern dryer is quite simple, but brings a lot of benefits. And how to hang it and fix it on the ceiling? Can it be attached to the wall? How to hang her right? What tools and materials will be required in the installation process? The housewife will have to deal with this, and this article will facilitate his work a little.

Modern Liana dryer is an excellent replacement for obsolete linen ropes

The advantages were dried by Liana

Like any other dryers for home use, Liana has its advantages, because of which this design is so fell in love with customers and made it popular.

Among the main advantages can be distinguished:

The dryer is installed under the ceiling, it is not noticeable and is harmoniously combined with the situation

Winch tubes can be adjusted in height, and this is very convenient for daily use

Liana can also be installed in the corridor or any other accessible and comfortable place

Eternal Lantern from Magnet Exposition

And under the table a hefty transformer or tesla coil. Naebalovo.

At least you can imagine how the magnetic field works, how this light is arranged and that you need to light it up? She did not light up at the base where the spirals are located. You see where it began to burn from, it means under this place (or from the side of it where the camera does not look) is a radiation source.

If the flashlight is eternal, then I will only ask you to send it on and in more or less transparent packaging.

Damn Afftar, well, for a look, at least wound a larger wire, or what kind of board I soldered. but it turned out too thick Naubalovo))

Damn, dude, where you were in November, when Crimea went out? I would be ozol. Well, I would pay you interest

You go under the power lines, stick a daylight lamp into the ground, rejoice, also magic to me))))

assemble, dryer, magnet, battery, make

In this video, you will learn how to make an eternal flashlight from a magnet and copper wire. Such a lantern will help you save electricity, and will also serve as a good substitute for suppositories in the event of a power outage.

21 COOL BATTERY LIFE HACKS

For the manufacture of such a flashlight, you will need a magnet from the old speaker, copper wire in isolation and lamp. From a set of such non.cunning tools within a few minutes, anyone can build an eternal flashlight.

Free electricity from two magnets and a piece of wire. You can assemble this BTG model with your own hands. Free energy is available in every house, collect your flashlight. Or the device is more serious.

Twist the second contact, and the lamp is already shining

That you can become part of a community where there is a knowledge base in which a collection of ready.made instructions for BTG assembly, drawings, schemes, discussions, and the same enthusiasts.

In the community of Fryteslanerji. you can always find friends and like.minded people, the same enthusiasts of free energy.

We have collected a collection of instructions, models, BTG drawings that you can collect and you. Enter the closed community of Freeteslaenergy enthusiasts

Community members together discuss the models and assembly of the authors, look for those who can assemble an unlimited energy generator for lighting or heating a house or apartment.

Write below on this page, about your experience, what you think about it.

We make a hinged dryer for a radiator of heating with our own hands

Consider the manufacture of a popular version of the dryer drying pipe with three lines for linen. We will need the following materials and tools:

  • polypropylene pipe with a diameter of 20 mm and a length of about 3.5 m;
  • tees of the corresponding size of 4 pcs;
  • corners of the same diameter 4 pcs;
  • plugs of the corresponding size of 4 pcs;
  • special soldering iron for pipes or glue for plastic;
  • scissors for cutting plastic pipes or a knife.haired woman for metal.

First, we cut off the nozzles necessary for assembling the design. It is convenient to use a special pipeline, but it is allowed to perform this operation and a conventional scabbard for metal.

In this case, there is no need to ensure sealing the joints, and the accuracy of cutting does not have.

You can adjust the sizes of parts based on specific conditions. For the example under consideration, we will need:

  • 4 segments with a length of 6 cm between the lines for placement of linen;
  • 2 segments with a length11 cm for the formation of hooks;
  • 2 segments 25 cm long for vertical elements of hooks;
  • 3 segments 80 cm long as linen lines.

As a result, we get a complete set of parts necessary for assembling the design.

In the presence of a soldering iron to docking heating pipes and water supply, the drying assembly is performed with its help. In the absence of a special tool, you can use glue. In detail about how this is done, read in the article “How to glue polypropylene and polyethylene, including foamed, which glue to glue it to concrete or metal?””

The result is the design presented in the photo.

It remains to carefully insert the dryer into place, and you can call your wife to boast!

Another option from polypropylene pipes

Of course, the size of the dryer can be different, and the number of linen lines can be increased. In this case, it turns out to save a little material, and the principle of installation on the battery will be different. The fact is that the windowsill sometimes hangs over the heating radiator and does not allow you to insert the dryer from above.

In this case, you should make a frame from plastic pipes, as indicated above. As a hanger for linen, you can use a cord or stainless wire, which is threaded into the holes in the pipes. Do not pull the ropes too strongly, as the frame may bend.

For mounting on the battery, two m 8 bolts about 120 mm long are used in the kit with nuts and washers. They are fixed in the holes on the long side of the frame at a distance corresponding to the size between the gaps in the radiator. So that the bolts do not scratch the battery, they put on heat.shrink tubes and expose them to heat. You can mount the dryer in place and use it!

A magnet from a nail

Today I would like to tell you how to make a simple electric magnet.

Maybe someone already knows this or studied at physics or craft lessons. I’m going to show this to those who still don’t know this. We need a copper wire, island, a battery aa, a nail, scissors, in the box there are pins for testing.

First we need to wrap the copper wire around the nail.

It looks like this. It is necessary that the coils are dense. Cut the ends and remove the isolation.

assemble, dryer, magnet, battery, make

Then connect the terminals. Cut a piece of isolets. Connect one contact to the minus, and the second to the plus. We have such an electric magnet. Let’s check it.

Wooden structure of bars and ropes

This option is somewhat simpler than the previous design. For the manufacture of a drying dryer, you need a beam size of 20×30, a skein of a strong rope, self.tapping screws for working with a tree. In addition to self.tapping screw, you need to prepare a screwdriver and a hacksaw in advance.

The assembly instructions are as follows:

  • Measure the parameters of the radiator and draw on the scale a sketch of a future dryer. The design will be attached to the battery using hooks. External crossbars play the role of support, making the product more sustainable. Make sure that the supports of the width correspond to the size of the radiator.
  • The type of dryer is simple. this is an ordinary frame with twisted screws, slightly protruding out, so that you can hook the rope behind them and pull it like strings. The design only seems to be a flimsy in appearance, but in reality it is very reliable.
  • Treat the tree with a fine.grained skin so that the surface is smooth and without pits. It is very simple and will not take much time. Carry out closing work in dense gloves and respirator so that wooden dust does not fall into the nose and mouth. If desired, make sharp rectangular faces of the beam rounded, so as not to be accidentally injured about them. This is especially true if there are children and pets in the house.
  • The assembly of the frame is easier than in the previous version. Cut the beam into details of the required length and collect the frame first, and then the support. When both details are collected. connect them to each other.
  • Wood. material vulnerable to water. Cover the surface of the finished structure with a layer of a special composition that protects the tree from moisture. The dryer will acquire a beautiful appearance and will last you longer.
  • Wait for when the underwear dryer completely dries and tightly pull the linen rope between the screws screwed into the frame. Now you can hang this frame on a heating radiator.

Folding option

This option for your own assembly is best suited when the battery is drowned into a niche. The dryer is attached to the wall above the heating device and is laid out and folded when it is necessary.

  • folding mechanism;
  • hooks for drying towels (instead of them you can use furniture handles);
  • fasteners;
  • paint (acrylic or water emulsion);

Having prepared materials, it’s time to get down to business:

  • In the side beams of the frame, drill holes corresponding to the size of the rods. Make sure that they are plowing the same in length, fix them in the holes. For convenience, slightly flow the ends of the rods. After that, you can completely assemble the frame using ordinary nails.
  • The base should be larger than the frame from all sides by 1-1.5 cm. Fix both parts of the structure using one or two loops depending on the dimensions of the dryer itself.
  • The turn for staining. Paint the design in one color or use a combination of several shades. Wait for the paint to completely dry before the next stage of work.
  • Install the lock at the top of the dryer, and from the sides of the folding mechanism. It is important to accurately calculate the opening angle. Should be strictly 90 degrees.
  • At the bottom of the structure, attach hooks intended for small clothing items (gloves, hats, etc.D.) and underwear.
  • Drill a hole in the wall above the battery and install the dryer.

Belt dryer on the wall above the battery

DIY battery

With the onset of cold weather, dry linen on the balcony becomes problematic. Parents of small solders who can stain a lot of clothes for money will be especially understood, so much an adult would have been enough for a month. It would be nice to make an additional place for drying. At the same time, do not pull in the kitchen a web of ropes that will spoil the whole view.

The master has a cable as a rope. Now it remains only to stretch it into the hole. If you need to serve some heavy things, then the dryer can be an amplifier by installing one tee in the short directions. 45 degrees corner, emphasis on the battery from the pipe. As a result, we get a rectangular linen dryer, which can be easily installed on a hot battery.

The second idea

Further, there is also a similar design (Texas TV channel), but instead of a rope there is a pipe here. Which of the two proposed ideas to implement is up to you.

For the manufacture of dryers, we will use scraps 20 polypropylene pipes. You will also need a certain number of tees. Accordingly, to connect these pipes into a rectangle. corners. You also need a curling iron to solder the device. If this tool is not, you can do without a curling iron using a gas burner.

assemble, dryer, magnet, battery, make

First we remove the dimensions of the radiator to find out where the fastening places will be. We begin to solder. The result should be a blank that needs to be duplicated on the second side in a mirror reflection. Subsequently, it will be possible to solder them.

In the manufactured design for linen 3 rods. If necessary, instead of the corner, you need to put the tee and continue, add another bar. The dryer has a presentable look. It is practical and functional. You can dry both underwear and shoes.

will pistols work if stuck in concrete?

How to choose a ready.made option

If you decide to buy a product ready, it is important to take into account several useful recommendations:

Correspondence of the structure Not all such products are the same, some of them are made for a certain type of radiators and are not suitable for others. Be sure to keep in mind this nuance, since it can be problematic to return the product after unpacking
The strength of the elements On the market you can find options, the price of which is low, but the quality leaves much to be desired. Make sure that the strips do not bend from the slightest effort, otherwise you can hardly use the product normally. Also pay attention to the quality of the performance of parts, there should be no visible flaws and factory marriage
The size of the system Options can be of different sizes, you must decide for what purpose the dryer will be used and what size of the structure will be optimal in your case. Of course, it is wiser to purchase more options, as a rule, the system will always be filled with any things

Important! Sometimes the purchase of two such products will be more justified than the purchase of a suspended dryer or other expensive design, so weigh the pros and cons and decide what you want to get ultimately.

Wooden structure of bars and ropes

This option is somewhat simpler than the previous design. For the manufacture of a drying dryer, you need a beam size of 20×30, a skein of a strong rope, self.tapping screws for working with a tree. In addition to self.tapping screw, you need to prepare a screwdriver and a hacksaw in advance.

The assembly instructions are as follows:

  • Measure the parameters of the radiator and draw on the scale a sketch of a future dryer. The design will be attached to the battery using hooks. External crossbars play the role of support, making the product more sustainable. Make sure that the supports of the width correspond to the size of the radiator.
  • The type of dryer is simple. this is an ordinary frame with twisted screws, slightly protruding out, so that you can hook the rope behind them and pull it like strings. The design only seems to be a flimsy in appearance, but in reality it is very reliable.
  • Treat the tree with a fine.grained skin so that the surface is smooth and without pits. It is very simple and will not take much time. Carry out closing work in dense gloves and respirator so that wooden dust does not fall into the nose and mouth. If desired, make sharp rectangular faces of the beam rounded, so as not to be accidentally injured about them. This is especially true if there are children and pets in the house.
  • The assembly of the frame is easier than in the previous version. Cut the beam into details of the required length and collect the frame first, and then the support. When both details are collected. connect them to each other.
  • Wood. material vulnerable to water. Cover the surface of the finished structure with a layer of a special composition that protects the tree from moisture. The dryer will acquire a beautiful appearance and will last you longer.
  • Wait for when the underwear dryer completely dries and tightly pull the linen rope between the screws screwed into the frame. Now you can hang this frame on a heating radiator.

Belief dryer for heating radiator

We have a large balcony suspended system for drying Liana’s drying. Not so long ago, I published a review with the replacement of rollers for this dryer. We use her constantly, but when you need to dry something quickly, especially in winter, we hang the linen on the batteries. But here we have difficulties. there are not enough space on the batteries. In the hall, batteries are closed with decorative lattices, and in the kitchen, a soft corner with a high back is standing back to the battery. do not crawl. To increase the drying area and this dryer was purchased. The option with a floor dryer is not very suitable for us, since it is simply nowhere to put it in a tiny kopeck. But this option with a fastening on the battery fit just right. The dryer is supplied in a simple plastic bag, judging by the avenue, the dryer is made in the Udmurt Republic, in g. Izhevsk. The length of the drying canvas is 2.1 meters (they counted all the rods at once). The maximum load weight 5 kg drying has a folding structure. The frame is made of metal. Pruteyev or drying paintings five. The length of the paintings is almost 45 cm (the seller has different dimensions), the width of 23 cm the frame is well painted, should not rust. Suspended hooks have an isolation similar to neoprene. The ends are also closed with plastic plugs of the clamps, and durable to the touch have an internal profile with grooves for fixing on the canvas gathered elementarily. With effort we insert the extreme crossbar into the latch. We pushing the second latch and also snap on the opposite crossbar of the same thing with the second hook. The dryer is collected and ready for installation on the battery, try it on the place. We will have it a corridor battery in the form of a heated towel rail. The dryer got up perfectly in connection with a constrained place of use, I chose a dryer 45 cm long, but even a T.shirt, a towel, several pairs of socks are placed on it and, I apologize for the ladies for such an intimate detail, cowards. And another canvas remained free socks, to be precise, 2.5 pairs were placed, 5 kg. We suspend a 5 liter eggplant with water. there are no problems, the dryer is slightly bend, but the weight holds perfectly when we do not use it, we don’t remove the dryer, but simply fold it and raise it is convenient, made with high quality, I recommend it to the purchase.

Summarizing

Linen dryers installed on the battery or set next to it are compact and convenient to use. The designs are easy to install, and their assembly does not require special financial costs and effort. Small models will fit into small apartments. But, if possible, it is better to purchase ready.made dryers.

We recommend reading an article on how to calculate the number of heating radiators for the apartment area.

How to choose a ready.made option

If you decide to buy a product ready, it is important to take into account several useful recommendations:

Correspondence of the structure Not all such products are the same, some of them are made for a certain type of radiators and are not suitable for others. Be sure to keep in mind this nuance, since it can be problematic to return the product after unpacking
The strength of the elements On the market you can find options, the price of which is low, but the quality leaves much to be desired. Make sure that the strips do not bend from the slightest effort, otherwise you can hardly use the product normally. Also pay attention to the quality of the performance of parts, there should be no visible flaws and factory marriage
The size of the system Options can be of different sizes, you must decide for what purpose the dryer will be used and what size of the structure will be optimal in your case. Of course, it is wiser to purchase more options, as a rule, the system will always be filled with any things

Important! Sometimes the purchase of two such products will be more justified than the purchase of a suspended dryer or other expensive design, so weigh the pros and cons and decide what you want to get ultimately.

Such a system is not only convenient to use, but also attractive outwardly

| Denial of responsibility | Contacts |RSS