How to assemble a floor Sakura fan

Fan types

Fans of different systems remain a popular way to solve the problem of creating more favorable living conditions. According to the method of installation, they are divided into the following types:

The last two varieties, in most cases, do not require assembly after purchase. Ceiling options must be installed in a place prepared for their installation.

Models differ in power, size, airflow area, number of speeds, noise level and a variety of additional functions. Floor fan remains one of the most common ways to cool, increase the level of comfort. Wide application is connected with low price of this kind of products, simplicity of exploitation and installation, low power consumption, mobility, universality (the wind blowing from the fan freshens even on the street). The technique takes up very little space.

The following varieties of floor fans are distinguished by the method of work:

  • Axial. these are devices equipped with an electric motor and blades (enclosed in a casing of mesh), which when rotated, set the air in motion;
  • radial. mechanisms, made in one body, inside of which the rotor with blades draws air and then pushes it back;
  • Bladeless are circular frames with a motor that draws air in and pushes it outward with acceleration.
assemble, floor, sakura

Info how to disassemble and assemble floor fan

The first variant is the most common type. It does not affect the entire room, it blows on individual areas. It is the question of assembly that comes up when buying the axial version of fans

SAKURA SA-0601GR instruction manual online. Page 4

SAKURA SA-0601GR manual for the device humidifier contains pages in Russian.

File size: 132.80 kB. It consists of 4 pages.

assemble, floor, sakura

You can download the pdf file of the instruction: Download PDF

Take out the spout and remove the cap from the reservoir.

Hold the handle, turn the water tank upside down and unscrew the valve cap. For

To do this, press the button in the middle of the valve and keep it pressed while turning the valve cover counterclockwise.

Fill the tank with pure water that does not exceed 40ºC.

It is advisable to use distilled or purified water in order to prevent a white deposit from forming on the inside of the water tank and on the surrounding items.

Screw the valve cap back on tightly and make sure the reservoir does not leak.

Place a container of water on the base of the device by aligning the tab in the

Use a water tank with a valve tray and turn the water tank clockwise.

WARNING! Do not operate the humidifier without water in the tank.

Turn the steam regulator clockwise to the right, should be

you hear a light “click”, it means that the device is switched on. The operating indicator light will illuminate. The humidifying intensity can be increased or decreased by turning the knob clockwise from MIN to MAX.

When the humidifier is in normal operation, the indicator light is green

in color. If there is not enough water in the device, the light changes color to red.

To turn the appliance off, turn the knob counterclockwise until you hear a “click”,

The indicator light turns off, then unplug the appliance.

MAINTENANCE, CLEANING AND STORAGE

tutorial download 10 pose terbaru sakura lengkap!!! pasti bisa

Use water that has been purified and not more than 40 degrees Celsius. Wipe the water tank thoroughly with a dry cloth before placing it on the base. Periodically change the water in the tank from stagnant to fresh water. If you will not be using the appliance for an extended period of time, unplug the power cord, wipe all parts thoroughly with a soft, dry cloth and completely dry the water tank. CLEANING Cleaning the water tank and valve is recommended every 2-3 weeks. Clean water tube and ultrasonic transducer once a week. WARNING! Always unplug the appliance before cleaning.

CLEANING THE WATER TANK AND VALVE. Remove the water tank and turn it upside down Unscrew the valve cover Wipe with a soft cloth and rinse the water valve Rinse the water tank with water (temperature max 40º).

Clean outside of humidifier. Wipe outside of humidifier with a soft cloth and warm water (temperature max 40º). WARNING! Do not use organic solvents, chemicals or abrasives to clean the appliance.

STORAGE. Before storing the instrument, clean it according to the instructions in this manual Pack the instrument in its box and put it in a dry place.

POSSIBLE MALFUNCTIONS AND TROUBLESHOOTING

Indicator light is on but no air is coming out and

The warranty period is 12 months from the date of transfer of goods to the Consumer.

The warranty repair must be made in the authorized service centers listed in the warranty certificate.

The terms of warranty do not cover periodic maintenance, installation or adjustment of the product by the owner, nor does it cover normal wear and tear of the product.

RUS Floor Fan.

Turning mode button Motor shroud Shaft Control box

Screw B12. Screws13. Tilt adjustment screw14. Decorative cover15. Retractable rod16. Rack clamp17. Rack18. base19. Timer

Read this manual carefully and keep it as

Improper handling could result in damage and harm the product

Before using the product for the first time, check that the technical characteristics of the machine are within the recommended limits

Product specifications, indicated on the sticker, the parameters of the power supply.

Use only for household purposes according to this manual

operation. The appliance is not intended for industrial use. Do not use outdoors. Always unplug the appliance before cleaning it or whenever you are not using it.

To reduce the risk of electric shock or fire, do not immerse the appliance in water or other liquids. If it

DO NOT touch the product, immediately disconnect it from the mains and have it checked by a service center.

Do not use it in bathrooms or near water. Do not place the appliance near heat sources. At

to avoid electric shock do not operate the appliance with wet hands.

See also  Floor standing gas boiler with electronic control

Do not allow children to play with the appliance. Do not leave the appliance switched on unattended. Do not use accessories that are not included in the package.

Do not attempt to repair the appliance yourself. In the event of a malfunction, contact your nearest

Do not use the device with a damaged power cord. Make sure that the power cord does not touch any sharp edges or hot surfaces

surfaces. Do not pull, twist or coil the power cord around the unit. Avoid contact with moving parts. Do not put pencils or other objects through the guard of a running fan. Do not operate the fan without the guards in place.

The fan is shipped unassembled. Before beginning assembly, make sure that the scope of supply is complete and

Do not connect the unit to the mains before fully assembling it. Put the stand on the base and fasten

screws (included). Remove the clamp from the stand, put on the decorative cover and lower it onto the base. Extend the boom to the desired length, set the clamp in place and tighten. Attach the motor and control box to the pole and fasten it with screw B.

Unscrew fixing nuts: blades. clockwise, and the rear grille. counterclockwise, and remove them from

of the fan shaft. Slide the rear grille onto the fan shaft. Screw the rear grille nut on the shaft and tighten it.

Place the blades on the shaft so that they reach the latch. Tighten the blade retaining nut counterclockwise to lock them in place. Align front and rear grille so that the logo is centered

Check. that. fan. straight. in. front. grille. and. fasten. circumferentially. with. retain. clips. Fix the angle of the fan with the screw. Fan ready to run.

NOTE: To avoid electric shock or fire, do not operate the ventilator under conditions of

If the fan is exposed to high humidity Place. fan. only. on. a. level. dry. stable. surface. The fan can operate in three speed modes:

“1”. minimum fan speed;

On the motor housing there is a button to activate the fan rotation mode. If you press (sink) this button,

Motor with blades will start to rotate in different directions. To cancel the rotation mode, pull the button back.

Set the desired operating time with the timer. To turn off the fan, press the “0” button.

Always disconnect the unit from the power supply before cleaning. Do not use abrasive cleaners. Wipe the grille, blades, stand and base with a damp soft cloth and then wipe dry.

Fan Troubleshooting and Ways to Troubleshoot the Fan

To reduce costs and achieve low noise levels during operation, sleeve bearings are installed in fan motors. As a result, after a couple of years of use, the lubricant will wear off, and this is the most common cause of fan failures.

Table of fan failures and repair recommendations
External manifestation of the malfunction Possible cause of malfunction Troubleshooting Method of repair
Fan turns off and then on again some time after normal operation Self resetting thermal fuse from overheating of the windings triggered Check impeller’s free rotation, disassemble the fan and inspect stator winding for blackening Lubricate the bearings, rewind the winding
Fan turns on, but blades rotate slowly The grease in the motor bearings has thickened or worn out At insufficient lubrication of bearings the fan at work makes the increased acoustic noise and there can appear smell of burning from overheating of the electric motor windings Fan must be disassembled and sleeve bearings lubricated with machine oil
Mechanical wear of the motor bearings due to lack of lubrication. Often the impeller vibrates in relation to the center of rotation Jiggle the impeller relative to the center to the sides. If the play is more than 0.5 mm, the bearing is worn out Replace the bearing with a new one
The fan doesn’t start, the blades don’t rotate Cord is not plugged in Check the remote control unit’s battery is flat Check the unit’s battery Insert the power cord plug into the outlet
No voltage in socket Check voltage at the outlet using a functioning electrical appliance Connect the ventilator to a working socket
Power cord is defective Visually inspect the plug and cord for mechanical damage, check the continuity of the cord wires with a multimeter If defective, replace the power plug or cord
The switch or speed switch is defective. The battery in the remote control is flat The fan should be opened and the switch should be tested with a multimeter. Resistance between the switch contacts should be zero when the switch is in the ON position If the switch is defective, replace it. If there is no device at hand, you can short-circuit the contacts of the switch, and turn off the fan by removing the plug from the socket
The fan hums and gets hot when switched on Rotor shaft is jammed because of grease wear or thickening Disassemble the fan, wash with solvent and grease bearings
Fan hums and heats up when switched on Start winding or capacitor breakage. Turn the impeller by hand, if it rotates it means to replace the capacitor or try to find the place of starter winding breakage
Rotor winding breakage Check the windings for mechanical damages and local darkening by visual inspection, check the windings continuity using a multimeter If a winding breakage cannot be found visually, the winding will have to be rewound, which is not economically feasible
Thermal fuse has triggered due to overheating of the electric motor Check continuity of fuse with multimeter. Resistance of the thermal fuse should be equal to zero. To check in the absence of a device you can temporarily short-circuit the terminals If a thermal fuse breakage is found, replace it with a good one. If the new fuse burns out again after a short time of the fan work, the motor is defective

For reliable operation of the fan it is recommended before each season of operation to disassemble it and lubricate the bearings with motor oil. But no one is doing it, including me. Usually it is engaged when the blades stop rotating or the fan began to make a lot of noise.

How to make a cut plastic washer Where to find a rubber ring for replacement

By e-mail I received a letter in which a visitor to the site Vasily shared his experiences with the repair of coolers. I liked his advice, I think it will be useful for many, who will face with the repair of the cooler.

I often have to do cooler repair and decided to share my experience:

If the cut plastic washer is lost or broken, it can be made from a plastic card of a travel ticket, the main thing is to find a card of appropriate thickness. Business cards made of the same material will also do.

See also  How to assemble a floor fan vitek

If the rubber ring is crumbled, torn or lost, a gas lighter can be used as a donor. It has a good-sized rubber ring under the valve. Different models of lighters have different ring thicknesses, so you have to find the right one. If you got a ring thicker than necessary, you need to install it on the bottom of the impeller shaft, and under the fixing washer put what was previously on the bottom of the impeller shaft.

How to assemble the floor fan Tefal

Did you know that there are fans that also protect from mosquitoes? Tefal with combined fresh air and mosquito repellent spraying system. My salvation in the summer heat

Now I want to tell you about the floor fan Essential (Mosquito) Protect VF4210 from Tefal.

The Tefal VF4210F0 floor fan creates a cool breeze and keeps the air from stagnating.

Three speeds allow you to select the most comfortable option: from a gentle whiff to a powerful stream (up to 55 cc per minute).m/h). The settings are set with a mechanical rotary knob.

Above the control panel is a special slot where you can insert any standard bottle of liquid fumigator. So the fan not only freshens the air but also sprays insecticide throughout the room.

The fan is packaged in a large cardboard box that weighs a lot. A girl, for example, can be carried to the car, but only if carefully.

At the base there is a little information about this fan model. The main characteristics and advantages are written.

There is not much information, but it is provided in several languages at once.

I did not find it very convenient that the box is not equipped with any handle.

Everything inside was folded up very tightly, so even if you turn the box upside down. Did not shake or rattle.

Tefal VF4210F0 Floor Fan Review

The fan is sold unassembled, so you have to assemble it yourself. Each element is carefully packed in protective material, only the blades were without everything.

The first, and probably the heaviest part. The stand for the leg.

It was packed in a plastic bag.

Inside of which there were additional parts to assemble. I liked that all sorts of screws and screws went right along with the parts where they had to be screwed in.

The stand weighs a lot and thanks to it the fan is stable even at maximum speed.

At first I didn’t quite understand why the stand was so dirty. But after wiping it with a rag, I found that it is itself a plastic in such an interesting color.

On the outside the stand is made of white plastic. The outer rim. glossy, and the inner circle. frosted.

Next comes the leg. It’s firmly packed in cardboard.

And also wrapped in film so nothing gets scratched.

It is not particularly heavy, although it is made of metal. Visually it is glossy and smooth. Sold short, but you can adjust the length to your liking. Maximum height of the fan. 140 cm.

Next comes the base, which, like all other parts, is carefully packed in protective material.

It’s probably the strongest protected, since it was first in cardboard and foam, and then. in a package.

The cord is also wrapped in foil and still coiled on the inside with wire. Its length. 1.5 meters.

The base, on which the fan basically works, is also quite weighty.

Looks like a machine speed checker.

The glossy black plastic head is threaded onto the base.

On the back there is a small sticker with the power of the device and the brand logo.

assemble, floor, sakura

There is a compartment on the base that makes this fan model different from all others. The mosquito function.

The cover is very tight, I almost broke a couple of fingernails the first time I opened it. Then I realized that it’s better to use fingertips.

You can screw any insect repellent into the compartment, and when the fan is running, press the button labeled Protect, and the airflow will start to spread the liquid around the room.

They are made of a sturdy transparent plastic of a blue hue.

They are not particularly wide, which allows them to spin quickly and easily.

The parts of the case that protects the screw were in the same package.

Inside was some incomprehensible and unnecessary paper.

The case has two parts of the same shape. They lie inside each other, and between them are a couple of paper sheets.

The top half has the logo located on the plastic circle as well as the outer rim.

The back panel on the other hand is all metal.

When assembled, the base turns out quite voluminous.

It is easy for air to pass through the small mesh, but it also does a good job of protecting against the spinning screw.

As I wrote earlier, the fan is sold in a disassembled state. Assembly is easy in principle, it does not take much time if you study the instructions beforehand. I did it in about 20 minutes.

In the instruction there are variants of assemblies of several models at once, so look for yours by number. Mine is the one on the left.

To begin with you have to assemble the lower part of the fan.

Then comes the upper part with the twisting mechanism.

It should be placed in the open part of the stand.

Beforehand it is necessary to unscrew the screw inside, otherwise the stick itself will not fit tightly and will fly out.

It is unscrewed by means of a special mechanism.

If you want you can immediately adjust the height of the finished fan.

From the base, which twists the screws, you will need to unscrew a couple of parts.

It is easy to do, because they have indications of which way to turn.

They unscrew quickly and without problems.

No need for any wrenches and screwdrivers, all done by hand.

Tefal ESSENTIAL Fan []

In front of us there is a pin, on which we need to thread the parts of the base and the blades.

Then it is screwed with the thing that we unscrewed the second. Make sure everything is screwed tightly and does not hang out, because you do not want the fan with the working part of the blades, God forbid, flew away?!

Review: Floor Fan Zanussi ZFF-907. Can’t be at home without a fan in summer.

I want to share with you my impressions of floor fan Zanussi ZFF-907, which we recently purchased on our favorite “berry” site when our good old one, which lasted almost 9 years, just fell to pieces. The fan has a small screwdriver, so we were looking for a budget one.

See also  Iron furnace for the garage with their own hands

Here, on Otzovik, I have not found reviews, and those that are written on the site itself. frightening interspersed with enthusiastic. I decided to tell you in order about our purchase here. so that before ordering it was clear what you’re buying.For the fan we paid 1899 (regular. specifically compared in regular stores in the city).In this box he came.

Basic information about the product is on the box.

In fact, what you need to know before buying: the fan has no legs, instead of a round solid (quite heavy) base, mechanical control. 4 buttons: three speeds and a button off, its weight is 4.5 kg and it is not bad in operation. That’s in brief.That’s how the fan was inside the box. since it’s new, of course, disassembled.

Here’s the base, we removed the film, it just shined. Except now the dust just sits on it.

The blades and protective grills were in a separate bag. Everything came in one piece.

And of course the instructions for use were inside the box.

My husband and I were struck by the blades. first of all, they are transparent.

Secondly, for some reason there is a feeling of fragility. but perhaps it’s just because of the transparent material.

This is how it looks when assembled. Very stylish, in my opinion, goes well with any interior.

This is how the control panel looks like. the usual buttons, but you can switch them quietly enough. we tried it already while the kids were sleeping and we had to put it from second speed to first for the night. Pretty convenient.

The protective grid is rather small, which is convenient in a house with small children. it’s harder to stick your fingers there. Not that impossible, but still.

As for the work. we were happy with it. The fan is powerful, it distributes the air well. On the third speed, of course, it is noisy, in the sense that you can hear it, but it is such a pleasant rustling. And we usually put it on second speed and switch it to first at night. it’s enough. At first speed, the fan runs almost silently, almost like a gentle whiff of wind.

Newsletter subscription

Exhaust fan. a device that can increasingly be seen in the homes of our fellow citizens. There are several reasons for this. First, in recent years, thanks to a significant decrease in the cost of production of such devices, almost everyone can afford to buy. Secondly, this electric device is certainly a very useful acquisition for apartments and private homes.

Electric circuit of a domestic fan and its peculiarities

The main task of the extractor fan is to provide forced artificial air circulation in those places where natural circulation is difficult or insufficient. A bathroom is a prime example of such a room. In apartment buildings, as a rule, this room is located far from the outer load-bearing walls, and, consequently, the circulation of air in them is difficult. If you add high humidity and mold, which appears because of it, it immediately becomes clear that the bathroom extractor fan is not just a tribute to fashion, but a real necessity.

In order to connect the fan, you need to know a few small nuances. It should be understood that the electrical connection diagram of the fan is largely determined by the location of its installation and the presence of features in its design.

Connection with a built-in switch. The simplest scheme. The device is connected to a power supply of 220 V. The fan is switched on and off by the switch built into the device.

Connection through a switch. Using this scheme, the fan is turned on and off using a special switch. As a rule, it is located in front of the entrance to the room. For such connection, it is necessary to lay two cables: one from the junction box to the switch and the other to the appliance itself.

Connecting a timer fan. The peculiarity of these devices is that they do not turn off immediately, but after a certain time. This is accomplished with a special time relay that automatically shuts down the unit after a predetermined period of time (usually one minute to half an hour). At such connection to the switch goes one wire, and to the device. two.

Connecting a fan with a humidity sensor. The electric circuit of fan control may provide for a humidity sensor, which measures readings in real time and, according to a given program, monitors the work of the device. makes it include when the humidity increases and turns off when it reaches optimum values. The connection diagram of the device is similar to that needed to connect a timer fan.

Most of the fans consist of switching circuits, start-up circuits, motor windings. The elements of the list concern the repair. Often in domestic models a trivial coil is used, wound with a copper core with lacquer insulation. Consider today how to do the repair of fans with their own hands, the inductance is burned out, the wire is torn because of the carelessness of the operator. To restore the coil a good old-fashioned device is used, in spite of its simplicity, you can not get it in a store. With the help of a mechanism, inductors are wound using an electric drive, working with their hands.

Industrial fans have a different way, unlike domestic more often centrifugal. The winding of a collector, asynchronous motor at home can not be restored, it will be difficult to do. Artisans repeat the production cycle of the factory in their hometowns.

Комментарии и мнения владельцев (24)

My CPU fan: “Cooler Master A9020-18RB-3AN-F1” started not spinning after my PC was idle (I start it by spinning it with my finger for 5-10 minutes). Decided to take it apart and lubricate it. It has a sticker on the top and bottom. Underneath is solid plastic Please tell me: can it be disassembled using the method described in this article.

Bogdan_S, I have not yet come across any fans that I could not take apart. Take a look at this article. Here is a description of how to disassemble another type of non-disassembled fans There is also a video, where the whole process is shown.

I took one of these CoolMasters apart today. also did not find anything. until I stumbled across this site. Disassembled the impeller on both sides at the same time. I don’t understand how it fits in there. the locking washer is more like a cover that covers the shaft

| Denial of responsibility | Contacts |RSS