How to change the plug in the washing machine

Instructions for replacing the electric plug

Instructions for replacing the electric plug will be useful for newcomers to electricity, who do not know which conductor to which pin to connect. To date, all appliances are connected to the network with a plug, which differs from the usual version of the presence of grounding. As a consequence, instead of the usual 2 wires need to connect 3 wires, which causes difficulties for some home masters. Below we will tell you how to change the plug on the wire, providing step-by-step instructions with photo examples, as well as clear video tutorials!

Which plug is better. collapsible or cast?

Cast plug is more reliable, its main advantage is the density of contacts, which are connected to the pins. The cast model uses spot welding, solder and crimping. Another advantage of the model is its tightness.

But there is an unfortunate disadvantage: it cannot be disassembled to fix the cause of failure. If the cord frayed at the base as a result of prolonged use, the only solution is to cut the cast plug to replace it with a collapsible model. It is possible to completely replace the cord and plug with a new one, but this requires disassembly of the appliance.

However, if such a replacement is not frightening, it is better to buy a cast product, especially because due to the increased reliability of such a plug fails much less often collapsible counterparts.

Joining Features

Reliable and long-lasting contact is achieved by soldering the wire connections, using a soldering iron and solder. Do not forget to remove the remnants and protrusions of solder, and treat the soldering points with emery cloth. If this step is skipped, the contact will break over time, especially when the appliance is running at high power.

It is quite realistic to do without soldering, putting on the ends of the wires before twisting pieces of brass tubing, the inner diameter of which is slightly larger than the diameter of the wire insulation. After twisting the wires, the tubes are moved to the joint and squeezed in several places, using a side cutter.

change, plug, washing, machine

After that, the gutted wires are tucked back into the cable insulation. the cut sheath. In this case does not perform insulation of the connection, because thanks to the shift of the stranded wire sections do not touch bare wire. The procedure is performed only if the indentation between the strands is less than 10 mm and requires additional covering with an insulating layer.

After you have finished your work, you only need to wrap the connection place with one more layer of insulating material. This is the easiest way to connect a plug with three wires. If you choose the right insulating material and a right length of cord, and also if you do the work carefully, you won’t be able to distinguish the add-on cable from a normal cable at first sight. the connection will be practically invisible.

As a result, it is possible to change the plug on the cord of an electric appliance by the method of escalation, in order to be able to operate the equipment connected to electricity.

Now you know how to properly connect the plug to the wire and, understand what steps the process consists of. After reading the simple step-by-step instructions, it becomes clear that electrical work is not as complicated as it may seem at first glance, and with some work you can cope at home on your own.

How to Change a Plug on a Wire

Detailed instructions on how to repair the electric plug will probably come in handy for the inexperienced person who can not independently figure out which pins should be connected to the conductor. In today’s world, almost all household appliances are powered by a euro plug, which can be made with or without grounding. Instead of the usual two wires need to connect three, this sometimes causes problems when you connect yourself. There are very simple ways to change the plug on the wire so that the appliances work properly again.

How to change the plug on your washing machine

Hello, in this video we’ll show you how to attach a plug (Europlug) to a cable, such as your TV cable. I will start by taking the plug apart to show the whole procedure from the beginning. The first thing to look at when working with euro plugs is the location of the wire sockets. The neutral and phase wire sockets can be on one side or the other. But the socket for the grounding wire is usually in the middle. I’ll show you a little bit closer. This socket is also marked with a grounding symbol. I will now twist the strands of the cable wire. They are already cut to the same length, but the grounding wire is a little shorter, as this will make it easier to secure the wires in their sockets. As you can see, I fix the phase wire on one of the pins of the plug. The grounding wire is attached in the center, above the grounding markings on the enclosure, this is the grounding point on the euro plugs. And also the neutral wire on the second prong. Well, as you know, there are only two pins inserted into the socket itself. Now we are going to make a cable clamp. With this clamp you will pull the cable out, not the wires themselves. In other words, if you decide to stretch the cable a lot, you will not damage the wire terminals, but only stretch the cable itself. Do not forget that on our site you can find a huge number of videos on repair of household appliances, as well as plumbing equipment. So, the fixing clamp is ready. All that’s left to do is secure the outer casing by sliding it up the cable. The cover can only be placed in one position because only one screw secures the entire plug. And, as you can see, the cable itself on the back of the plug can be secured in two ways. Thanks for watching. If you think this video helped you, repost it on your page or yourtub account. And also advise a friend, if he needs help. Thank you for watching, see you in another video.

See also  Samsung washing machine does not open the door

Well you need a new fork, a screwdriver and a knife and a couple of minutes of work.

You need at least a flathead screwdriver (small) and pliers. plug take 16A (met only domestic if the machine on power more than 2.2 kW. if up to 2 kW, buy a 10A unit (VIKO for example, looks neater than ours). All plugs have a grounding contact. (“Euro”) if anything.ask for help

The washing machine is supposed to be grounded. you need a special plug.

Don’t listen to anyone! For me, in a private message and write your phone, I come and you will not only work the washing machine, but also all the equipment that has not worked to this time. And then they invent some contacts, bolts, kilowatts and amperes. Do not believe them want to burn out the washing machine. Prepare for the next weekend products (I love deruny with meat) and I will come.

Stasik has the best answer. Tasteful and not without a hint!

Home Master Class Instructions for replacing the electric plug

Instructions for replacing the electric plug will be useful for newcomers to electricity, who do not know what conductor to which pin to connect. To date, all household appliances are connected to the network with a europlug, which differs from the usual version of the version with the presence of grounding. As a consequence, instead of the usual 2 wires need to connect 3 wires, which causes difficulties for some home masters. Next we will tell you how to change the plug on the wire, providing step by step instructions with photo examples, as well as illustrative video lessons!

How to change the electric plug on the wire

If there is a need to replace the plug on the wire, then first you need to determine its type, based on the power consumption of electrical appliances and the need for its grounding. In order not to hesitate, it is best to replace the faulty electrical plug, plug of the same type.

How to change the electric plug on C1-b

If there is a need to replace the plug on the cord, you must begin with the preparation of the ends of the wires for connection. To do this, cut the cord at a distance of 3-5 cm from the plug. If the plug due to poor contact in it was very hot, then usually the insulation of the wire at the point of exit from the plug is made rigid and this part of the wire should be removed. Then the wire insulation is stripped off to the length of about 20 mm and rings are formed at the ends. Screws are inserted into the rings, on which the spring washers are first put, and then the flat washers are put. Grooved screws are necessary.

Then the screw is screwed all the way into the pin. Connect the wire in the same way to the second prong. The pins are inserted into the housing with their protrusions into the special round recesses. Then the bar is put on the wire and pressed with two screws to the body. If the wire insulation is thin, it is advisable to put a rubber or PVC tube over the insulation to prevent fraying in the place where it comes out of the plug.

It remains to connect the halves of the body and tighten them with the screw and nut. If the halves are not touching each other completely, it means that the wires next to the tightening screw are in the way, so move them out of the way. To do this, unscrew the thumbscrews on the rings, turn the wire and tighten the thumbscrews back on. If you don’t do this, you could break the plug when tightening it. If you connect a cord that has three wires to the two-pole plug, then the yellow-green wire (grounding wire) does not need to be stripped of insulation and connected anywhere.

How to change the electric plug to a three-pole C6 plug

Prepare the ends of the wires for connection to the three-pole plug C6 in the same way as for the plug C1-b. The assembling technology is also similar. Most importantly, if the plug doesn’t come with grovers, be sure to find and install these spring washers. To connect the cord to the plug, you need to insert screws with washers into the ends of its wires, pre-formed into rings, and screw them tightly to the contact pads of the plug. Please note, the yellow-green wire can only be connected to the ground contact. It is usually in the middle between the pins.

If the cord is two-wire and does not have a yellow-green wire, then the grounding contact in the plug is left free.

See also  How to wash towels in a washing machine

How to replace a faulty electrical plug C5 or C6 by extending the wire

In practice, you may encounter a situation where the mains plug has failed, the electric appliance is in urgent need, and there is no collapsible plug for replacement at hand. It is a long way to the store, and not every village has an electrical goods store. But even from such a seemingly hopeless situation, there is a simple way out.

In almost any household there is, any faulty electrical appliance, such as an electric kettle. From it you can take the plug for repair and replace faulty according to the instructions below.

The picture shows an old kettle stand, from which comes the wire with the cast plug C6 at the end. The length of the mains wire of electric kettles is usually short, but if the length of the wire of the appliance where the plug is to be replaced is not long enough, then you can take advantage of the opportunity and make the wire longer. In this case, the wire from the kettle stand should be bitten off leaving its maximum length. Sometimes in the bottom part of the stand a part of the wire is wound on a reel. Therefore, its length can be longer than is obvious. If you do not need to extend the cord of the appliance, it is enough to leave about 15 centimeters of cord.

Next, it is necessary carefully not to damage the insulation of the wires, cut along the sheath of the cords for a length of about 10 cm and pull the wires out of the sheath. Attention, the sheath must not be cut off. There are usually three different colors in a standard cable. Brown (phase), light blue (zero) and yellow-green (grounding wire).

The next step is to adjust the length of conductors so that the places of future stranding wires were shifted relative to each other by a couple of centimeters. When fitting the length of the wires, remember that it is essential that the single-colored wires are joined together.

Next, remove the insulation from the wires to a length of about 15 mm. If one of the cables is missing the green-yellow wire, do not strip the insulation from the existing wire because it cannot be connected to anything. It must remain free.

In the next step, the stripped copper wire strands are connected to each other by twisting. Three windings are enough for a good contact.

The wires must be soldered with a soldering iron for a secure, long-lasting connection. In order to remove possible sharp solder projections and wire ends the soldering point should be treated with sandpaper. If you do not solder the splice, the contact can be broken over time if the power of the electric appliance is high.

You can do without soldering, if before twisting on the wires to put sections of thin-walled copper or brass tube with an inner diameter slightly larger than the diameter of the wire insulation. After stranding the wires, slide the tubes to the joint and flatten them in several places with side cutters.

Then the connected wires are tucked into the previously cut sheath of one of the cables. There is no need to insulate the connections, because thanks to the shear of the stranding wires bared sections of wires can not touch.

Then stranded wires are inserted into the previously cut sheath of one of the cables. There is no need to insulate the connections, because thanks to the displacement of the stranded wire sections do not have the opportunity to contact. If the distance between the twists is less than 10 mm, then they need to be covered with insulating tape.

Now all that’s left is to cover the cable joint with one layer of insulating tape, and the job is done.

As you see, the cord of the appliance is now fitted with a functioning plug by splice, and the appliance can now be plugged in for future use.

The spliced cables are white and black specifically for clarity. If you match the color of the plug and the PVC insulating tape to the color of the appliance cable, the connection point will be almost invisible.

The old electric plug and its replacement

The old electric plug has a simpler design. Here, the replacement methodology will be slightly different. Here are the basic steps that you will need to perform:

As you can see, the old electric plug has a simple assembly design. You can see how to do this in the video below. If you have a noisy washing machine, then you should read about this problem.

Replacing the old euro plug

You may need to replace the electrical plug if one of the pins is broken. The electrical plug has a simple replacement technology to which it belongs:

As you can see, the device of the electric plug is quite simple. If your refrigerator does not turn off, then you should read about this problem. This is why you can easily do the replacement yourself. You can watch this process in the video below.

Replacing plugs

The plug is an electrical connector, together with which the plug connection is provided. With its help, it is possible to quickly connect and disconnect the electrical appliance, using different socket contacts.

How to replace a faulty plug on HOOVER washing machine ( broken plug )

Most of the plug versions are equipped with special metal sockets, where the bare end of the wire should be inserted. It is tightened with a miniature screw.

Replacement of demountable plug

If you have an old-style electrical plug, it is collapsible and has only two wires, the instructions will be very similar to the previous. Grounding for this type of plug is not provided, therefore grounding wire muffle (cut off at the root). Let’s review step by step how to install the plug on the wire:

See also  What mode to choose for washing jackets

We tighten the body of the plug with retaining screws

Replacing the old Soviet-style electric plug

One of the most common plug designs in the USSR, designed for 220V

The old electric plug has an even simpler design than its previous counterpart. The replacement algorithm in this case is slightly different. The main steps, which consist of the replacement:

The final step is assembling the ready-made plug.

How to change a plug on a wire

It is not difficult to repair the plug for the socket, but during the work it is very important to pay attention to personal safety precautions.

How to disassemble the C1-B type electric plug

It is required to prepare the ends of the wires for connection. To do this, the cord is cut at intervals of no more than 5 cm from the plug. If the plug has overheated because of an unreliable connection, as a rule, the insulation in these places becomes rigid and must be replaced. At the ends of the wire rings are formed. After that spring washers and flat washers are placed on the screws. Now this construction can be inserted into the screws.

The screw should be screwed into the pin as far as it will go. Similarly, the cord is connected to the second plug. They are installed by the protrusions in the housing in special recesses. Place the strip on the wire and use two screws to hold it against the housing. If the insulation is thin, to prevent its abrasion in the place of exit from the structure, it is recommended to put a PVC or rubber tube over the insulating layer.

Finally connect the halves of the body and tighten them with a nut and screw. If the two halves of the wire prevent them from touching tightly, they must be removed.

How to connect a three-pole C6 plug to a wire

Preparing the wire for connection is done in the same manner as in the previous section. The assembly technology is the same.

If there are no fork plugs in the kit, they must always be installed. The yellow-green wire can only be connected to the grounding pin. It is usually located in the middle between the contact pads of the pins.

The two-pole cord does not have a grounding contact, so the plug will leave this space free.

How to plug the wrong plug into a regular socket

Many people are familiar with the situation of unsuitable plugs. You buy appliances from an online store, and you can’t plug them in. The problem is the pins of the plug are different in shape.

This situation can be handled with the help of an adapter. It represents an adapter. On one side of the adapter, a device with a non-standard plug is inserted. On the other side is a standard matching plug.

IEC 60906-1

IEC 60906-1 plugs are used in Brazil and South Africa. They resemble common Samsung chargers. The distance between the conductive pins is 19 mm.

The main difference of IEC 60906-1 from plugs familiar to citizen of the CIS is the additional grounding prong. It is placed in the middle. For sockets used in Russia, this grounding pin will have to be removed.

BS 1363

BS 1363 plugs are used in the UK. They feature conductive pins with a rectangular cross-section. These models also have a grounding contact.

To find an adapter for BS 1363 plug is easier than for IEC 60906-1. But if this is not possible, the plug will have to be replaced with any other suitable.

Notice the! BS 1363 plugs can be fitted with fuses. If the gauges show that the plug is open, check to see if the fuse has blown. This is possible if the automatic burner control has failed to work.

How to change a plug on a wire

It is not difficult to repair the plug for the socket, but it is very important to observe personal safety during the work.

How to Disassemble a C1-B Electric Plug

The wire ends must be prepared for connection. To do this, the cord is cut at intervals of no more than 5 cm from the plug. If the plug was overheated because of an unreliable connection, as a rule, the insulation in these places becomes rigid and must be replaced. At the ends of the cord form rings. After that spring washers and flat washers are put on the screws. This construction can now be inserted into the screws.

The screw should be screwed into the prong as far as it will go. Similarly, the wire is connected to the second pin. They are installed by the protrusions in the housing in special recesses. A strip is put on the wire and two screws are used to press it onto the case. If the insulation is thin, to prevent its abrasion in the place of exit from the structure, it is recommended to put a PVC tube or a rubber one over the insulation layer.

To finish, connect the halves of the housing and tighten them with the nut and screw. If the two halves of the wire prevent them from touching tightly, they should be removed.

How to wire a three-pole C6 plug

Prepare the wire for connection in the same way as in the previous section. The assembling technology is the same.

If the set is not provided with a fork, they must be installed. The green-and-yellow wire can only be connected to the PE contact. This is normally midway between the pins.

The two-pole cord does not have a grounding contact, so the plug will leave this space free.

| Denial of responsibility | Contacts |RSS