How to clean your iron from burnt cloth

Methods for Ceramic and Teflon

The main condition. do not use any abrasives. Even the smallest and softest particles will leave scratches.

Cleaning Pencil

The cleaning rod contains urea and organic acids. Some manufacturers add scented fragrances.

The pencil begins to melt when it comes into contact with the heated soleplate. The acids it contains react with the carbon deposits and dissolve them when exposed to heat.

  • open a window in the room and let some fresh air in, as the pencil gives off a pungent smell when it comes into contact with a hot surface;
  • Prepare the place by draping it with old newspapers or cloth, which can then be thrown away;
  • Heat the iron well, but not too hot, and unplug it;
  • take a pencil and gently press down to clean the soiled areas;
  • Remove the remains of the melted iron; wipe the soleplate with a damp cloth.

The final step is to clean the steam holes with cotton swabs.

Table vinegar

Vinegar can be used to clean a ceramic or Teflon iron soleplate. This is how to proceed:

  • Prepare a weakly concentrated acid solution, for 200 ml of boiled water take 2 tbsp. л. 9% vinegar;
  • heat the iron slightly;
  • Take a piece of clean soft cloth, soak it in the prepared solution, and clean the dirt.
  • Wipe the sole with a wet wipe and wipe off any excess moisture with a dry one.

Tip! Old, embedded soot could be cleaned with undiluted 9% vinegar with a rough cloth, such as a waffle towel.

Hydrogen peroxide

A ceramic or Teflon iron can be cleaned from a small burnout with 3% hydrogen peroxide. To do this, you need to heat the device and a cotton pad soaked in the solution, treat the problem areas.

Advice! If the iron cools down, warm it up again to remove the soot more easily.

Analogous to peroxide are hydroperitol tablets. Dissolve 2 tablets in 100 ml of water, and use the solution to clean the burnt electrical appliance. Hydrogen peroxide and urea are the active ingredients in the prepared remedy. The product is more concentrated and efficient than usual peroxide.

Ammonia solution

Regular ammonia can be used successfully to clean the surface of an iron. There are several ways to do this:

  • Moisten a cotton pad with ammonia and rub off the residue. Change discs as it gets soiled. No need to heat the iron.
  • Equal parts of ammonia and 9% vinegar, 1 tbsp. л. And thoroughly clean the ironing surface.
  • Take 1 tbsp. л. Mixed with rubbing alcohol, add 5-6 drops of fresh lemon juice. Scrub the spots, then use a clean, damp cloth to clean the sole.

Tip! Ammonia alcohol has a pungent smell, so the procedure should be carried out in a room with an open window or on the balcony.

laundry soap

You can get rid of a little soot on your iron with laundry soap. It is high in fatty acids and alkalis and does a great job with dirt. It is necessary to choose 72% soap.

There are two ways to use it:

  • Fresh soot can easily be cleaned with a mild soapy sponge. Make sure the iron is slightly hot.
  • Rub very hard deposits with a soap bar, then heat the iron and leave it on hot for 3 to 4 minutes. When the iron has cooled down, remove the soap and wax deposits with a damp sponge.

After the procedure, wipe the surface dry.


Clean the iron with a simple paraffin candle. In addition to it, you will need a small piece of clean cotton cloth.

  • Wrap the candle in the cloth, and heat the iron to 60-80 ° C, usually this corresponds to the minimum mode, designed for silk and delicate things.
  • Clean the surface of the soleplate with an improvised pencil. The wax will melt in contact with heat and remove the carbon deposits.
  • Remove the melted mass.

How to clean burnt iron bottom | Easy way to remove burnt fabric from an iron

Warning! It is important to keep the iron tilted so that wax does not enter the steam outlet holes. Otherwise, the next time you iron your clothes, you might ruin them.

This method is only suitable for slightly soiled areas.

Tools for glass ceramics

They have a liquid consistency, do not contain abrasive particles and do not scratch the surface at all.

  • Spray and spread the product evenly on the soleplate of the appliance.
  • Wait 1-3 minutes.
  • Wipe with a damp and then a dry cloth.
clean, your, iron, burnt, cloth

Tip from! If the soot layer is thick and stale, the procedure can be repeated twice to clean the soiled appliance completely.

Among buyers are popular means brands Luxus, Sanitol, Silit Bang.

How to clean your iron: 10 proven ways to remove limescale and carbon deposits at home, 90 photos

A dirty iron soleplate prevents the iron from performing its function properly. Spoil this household appliance can not only burn clothes, but also some other factors.

The most common ones are hard water in the tank, which over time leaves mineral clogs in the steam holes, and starchy sprays for splashing laundry while ironing.

To resume its normal operation, you can buy a professional cleaning spray or pencil, or try to fix the situation with improvised means. However, cleaning clothes from the iron is much harder than upgrading the iron itself, so you should not leave it unattended on your clothes.

The need to clean an iron from soot at home can arise for a number of different reasons. Even with the most careful handling, the platform of the appliance periodically gets soiled, which, dirtying the laundry, reduces the quality of ironing.

This is caused by burnt cloth which remains on the surface in the following operating conditions:

  • Excessive temperature setting. That leaves microfibers on the ironing platform, which accumulate over time and turn into soot.
  • Using poor quality water. Lime scale, which also forms in the iron, as well as in the kettle, makes the soleplate of the electric appliance rough. Lint and fibers from clothing quickly clog the platform, creating a thin, barely visible deposit. Slip quality decreases. Soiling builds up on the ironing plate.
  • Unintentionally leaving the appliance on the laundry. In that case the cloth will stick to the soleplate and further ironing will become impossible. Burnt particles must be cleaned immediately.
  • Damage to the platform. Any micro cracks and scratches also affect ironing performance and are a major factor in leaving burnt fibres and threads on the work platform.
  • When ironing things made of wool is often overlooked that it is necessary to first cover such products with gauze, which is best not to wet.

In order not to spoil a piece of household equipment, you need to periodically eliminate the resulting contamination in the form of burnt cloth, carrying out preventive cleaning.

Cleaning metal coated irons

Cleaning instructions for metal surfaces depend on the specific material. Metal bases are available in steel and aluminum. The steel surface is good because it has sufficient strength and good slip on the fabric. Also easy to clean. Common remedies to combat scum on the steel soleplate:

The easiest option. to apply laundry soap, this method was used in the last century. But soap can clog special holes, making it hard for steam to escape. It is also possible to get rid of soot with a wooden spatula, but care must be taken not to scratch the coating.

Aluminum soleplate irons are known as the most inexpensive devices. But the price usually corresponds to the quality, and to maintain the good work of such an iron requires careful and regular care. Aluminum soles are unstable and brittle, they quickly develop scratches and most often form soot. Do not use hard brushes and sponges to clean aluminum surfaces. It is possible to remove dirt using special pencils, baking soda or vinegar.

Use household chemicals

You can find special cleaners for burnt iron soles on store shelves. Affordable is a special pencil that includes ammonia alcohol. To clean the surface of the iron with this product, follow these steps:

  • Read the instructions on the product packaging.
  • Heat the device to the maximum temperature.
  • Draw the sole surface with a pencil. Try not to apply too much pressure with the pencil, so as not to break it.
  • Iron with clean gauze. This will transfer the soot from the iron to the cloth. To clean a steam iron, turn on the steam function and use a cotton swab to remove dirt from the holes.
  • After the appliance has cooled down, use a damp cloth to remove the remaining steam.

When removing dirt from the iron with a special pencil ventilate the room. Breathing in harmful vapors can be hazardous to your health.

Salt used as a cleaning agent has its merits. These include:

  • Efficiency. The abrasive quickly copes with dirt, and the absorbent feature of the substance also allows it to absorb departed particles of soot.
  • Availability. It’s hard to imagine a home that doesn’t have a minimum amount of salt.
  • , and its cleaning power is minimal.
  • Safe. The food product does not contain any harmful chemicals that could harm human health. Plus, no residue is left on your clothes when the product is used.
  • Ease of use. Even an inexperienced hostess can clean an iron.
  • Incorrect temperature control.
  • Iron in contact with the clasps on your clothes.
  • Hard water in the steam generator fills the steam reservoir and over time limescale deposits form around the steam outlets.

If there is a problem, you need to decide what you can clean the iron from the burnt cloth. Before choosing a cleaning method, it’s worth knowing the safety rules.

How to clean an iron with a Teflon coating using traditional methods

Many housewives know that folk methods are sometimes just as good as special remedies. The components are always on hand, do not lead to high costs, and at the same time effectively cope with the task at hand.

Clean the Teflon soleplate can be several folk methods, of which it is easy to choose the best option.

How to clean the soleplate of a Teflon-coated iron with laundry soap

Laundry soap, with which it is easy to wash away almost any dirt, also copes well with the removal of burnt fabric. To clean the Teflon coating, follow the algorithm:

  • Grate the soap on a grater.
  • Heat the electric appliance.
  • Pour the grate onto a cloth on a hard, even surface.
  • Iron the soap (it quickly sticks to the platform, so this procedure will not take long).
  • Turn the appliance off.
  • Wait for it to cool completely.
  • Rub the soleplate with a sponge or cloth soaked in water and vinegar.

There is another option of using laundry soap on the Teflon coating:

  • Heat the iron to a medium temperature, to avoid the risk of scalding during use.
  • Rub a bar of soap on the Teflon surface. Make sure the cleanser has completely spread on the soleplate.
  • Turn on the electrical appliance so that the cleaner begins to melt.
  • Turn off the power and wait until the coating has cooled.
  • Rub the surface with a piece of soft, damp material, carefully removing any soap residue.

How to clean the Teflon iron soleplate with vinegar

Acids are effective against many stains, quickly dissolving and eating them away. Clean the Teflon coating with 9% table vinegar or 70% vinegar essence. The procedure is as follows:

clean, your, iron, burnt, cloth
  • Pour 1 tbsp (0.3 oz) of the baking soda into a small bowl. purified water.
  • Add 0.5 tbsp. Vinegar or 2 to 3 tablespoons of vinegar. л. Vinegar or 70% essence.
  • Soak a soft rag in this liquid (it should be slightly larger in area than the iron’s platform).
  • Lay out the cloth on a flat surface.
  • Turn on the electric appliance and heat it to the highest possible temperature.
  • Iron the vinegar “planking.”.
  • When the iron has cooled down a bit, moisten the cloth again and place the appliance on it.
  • After 20 min. Wipe the Teflon surface with a sponge.
  • Holes on the sole may be worked into with toothpicks or cotton swabs soaked in vinegar solution.

There is another effective option on how you can remove burnt fabric from the appliance’s work platform:

  • Take a heat-resistant container in which you can place the iron.
  • At the bottom of the cloth place some ordinary pencils (on which the appliance will stand).
  • Mix in a separate bowl 1 part vinegar and 2 parts boiling water.
  • Pour the solution into the container with the pencils.
  • Place the iron on them, so that the water mixture covers the soleplate halfway.
  • Hold everything over low heat, so that the liquid does not boil, but just steams.
  • After 30 minutes. put the device away and wipe its platform with a dry rag.

How to remove soot from a Teflon iron with citric acid

Citric acid works effectively against burnt cloths and other dirt on the Teflon coating.

To clean the device by using it, there are a number of steps to follow:

  • Dissolve 2 tbsp (0.02 oz) of the paste in a small container. л. Acid in enough water to form a pulp.
  • Dip the edge of the cloth into the mixture.
  • Clean the soleplate of the iron, trying to clean even the hard to reach areas and holes.
  • Finally, it is necessary to go over the acid-treated surface with a damp soft flap.

If the soot on the working soleplate is stale, the method of using citric acid should be changed slightly:

  • Dissolve the paste as for the first version (the quantity of ingredients can be increased).
  • Heat the appliance to the maximum temperature.
  • Spread the mixture on a cloth spread out on a flat surface (ironing board).
  • Activate the steam mode on the appliance by pouring the appropriate amount of water into the reservoir.
  • Iron the cloth with lemon juice.
  • Clean the surface with a damp cloth and dry it.

How to clean the Teflon iron from carbon residue with ammonia

Ammonia is just as effective. It can quickly rid the iron’s teflon coating of all sorts of deposits, including sticky fabrics, burnt polyethylene, or lime particles. To effectively clean the surface, you need to:

How to clean the Teflon surface of an iron with hydrogen peroxide

Clean the adhered fibers and lint from the material that has accumulated on the Teflon coating, you can use a common antiseptic. hydrogen peroxide. To do this, you need to:

If the contamination is abundant, then the use of peroxide should be slightly modified:

  • Soak a cloth in cleaning liquid that will be the same size as or slightly larger than the area of the iron‘s working surface.
  • Heat the appliance to the maximum temperature.
  • Iron the wet rag.

When heated, hydrogen peroxide is more active, so this method can clean not only fresh but also old stains on the Teflon platform.

How to remove encrustation on a Teflon iron using toothpaste

Toothpaste is another option on how to clean a Teflon iron from burnt cloth. Sequence of care:

  • Apply the paste to the brush and rub it onto the surface of the appliance.
  • Turn on the iron and heat a little.
  • Unplug the iron.
  • Moisten the brush and lightly rub the Teflon platform.
  • Clean any paste residue with a damp sponge.
  • Allow the device to dry.
  • Repeat the procedure if needed.

How to clean a burned iron with Teflon wax

You can make a kind of pencil out of paraffin to clean Teflon irons:

  • Wrap the candle in a cloth so that it can be easily and safely held when working with a hot appliance.
  • Turn the iron on.
  • Wax the Teflon soleplate.
  • When the homemade pencil melts, the stuck-on dirt will run off with the wax.

How to clean a Teflon-coated iron with foil

An iron can be cleaned just as effectively with ordinary food foil. To do this, you just need to iron it with a hot appliance. All soot will be removed from the Teflon surface when it comes into contact with it.

How to clean the soleplate of a Teflon-coated iron with acetone

Acetone or thinner, as well as nail polish remover can quickly and safely clean the working platform from any kind of soot.

  • Soak a cotton pad in any of the solvents listed above.
  • Wipe the Teflon coating with it.
  • Dry with a clean rag.

Causes of fouling on your iron

If there is a problem, you need to decide what you can clean the iron from burnt cloth. Before choosing a cleaning method, it is not superfluous to get acquainted with the safety rules.

| Denial of responsibility | Contacts |RSS