How to defrost the drip refrigerator Liebherr two -chamber. What should not be done when defrosting

How to defrost the refrigerator Whirlpool two.chamber

Whirlpool how to defrost the freezer. How to defrost the Whirlpool refrigerator with two.chamber melamine dishes, in turn, have no marking, be careful, since its composition contains formaldehyde, lead, manganese and cadmium, so such products are prohibited for sale in many countries.

The refrigerator allows you to save food fresh for a long time. Like any household appliances, the refrigerator requires regular care. and the old summer cottage “Biryus”, and the two.chamber brand new Indesit will have to be periodically defrost and washed. It is important to know some features and nuances of proper defrosting in order to extend the life of your assistant.

Why defrost a refrigerator

Products are stored in the refrigerator, so crumbs constantly appear, fluids spill, which is why an unpleasant odor forms in the chamber after a while. Therefore, when defrosting, the device must be thoroughly washed. Hygienic care with defrosting will prevent the reproduction of bacteria.

In addition, the formation of ice carries an additional load on the compressor and, as a result, your account for electricity will be increased. Yes, and placing products in the freezer with a fierce “fur coat” is quite problematic.

How often you need to defrost the device

Here, the level of icy formation will tell you here. A signal for cleaning in refrigerators without an automatic defrosting system is the formation of ice with a thickness of 7-10 mm.

In matters of the necessary defrosting frequency, you need to focus not on the manufacturer of equipment, but on the built.in defrosting system:

  • The senior “Soviet” models of refrigerators that do not have a car defective system need to be defrosted quite often. at least 2 months at least once every 2 months.
  • The XXI centuries are made on the basis of two automatic defrosting systems:
  • drip technology: during the compressor operation on the back of the refrigerator, ice forms (hoarfrost). Then the compressor turns off, the hoarfrows melting, draining drops into a special container, and it evaporates. Therefore, such a technology was called “crying”. The lack of drip systems. automatic defrosting applies only to the refrigerator, but not to the freezer, which will still have to defrost manually;

Refrigerators with a drop of defrosting system work quite quietly and consume less electricity than their analogues

The No Frost system applies not only to the refrigerator, but also the freezer

Devices that do not require defrosting do not exist. Even refrigerators with No Frost technology periodically need cleaning. at least 1 time a year you need to get all shelves, containers and rinse the walls inside warm water. It is not recommended to do this with the unit on. the compressor will be overloaded.

Stage 5. Choosing a method of defrosting

If there is time, just open the door for melting ice naturally. Waiting time-5-8 hours, depending on the thickness of the ice coat. With this method, the device is defrosting the longest, but at the same time the method is the safest and most sparing for equipment.

How to quickly defrost a refrigerator?

There are 5 ways of accelerated defrosting:

Hot water vessels. Filled with water 60-70 degrees of pots or bowls on the shelves of the refrigerator and close the door. In order to avoid damage to the material, put the reservoir on a wooden stand or a thick towel. After 20-30 minutes of active exposure, a couple of ice will easily lag behind the walls of the refrigerator.

Hot fabric. Place a canvas moistened in hot water in the camera. The method is effective in the edges and areas with a small ice. As an alternative, you can use hot water heating pads.

Feng. Many of our readers and clients ask whether it is possible to defrost the refrigerator with a hairdryer. The answer is unequivocal: yes, but subject to the precaution. Use the average temperature regime. Do not direct the air flow to the sealing gaskets, since the exposure to heat will lead to a temperature difference and a subsequent decrease in the elasticity of rubber products. Follow the distance between the hairdryer and ice formations.

Thermalcenerator. Allows you to accelerate thawing up to two hours. The method is effective only in warm rooms. Direct the air flow to areas with the thickest ice, in no case install the device in the camera itself.

Special tools. Sprays are sold in household chemical stores that help remove ice crust in sparing mode. They also effectively fight harmful bacteria and eliminate extraneous smells in the device chamber. Such means are absolutely safe for human health, since they are biodegradable and do not fall into food products.

detailed instructions

The defrosting process includes several stages, the sequential execution of which ensures the rapid thawing of both cameras.

Turn off the refrigerator

Put the temperature controller to position “0”, then turn off the refrigerator from the power: during the defrosting process, the device door will be in the open state, while the chambers’ space will be filled with warm air, and the engine will begin to work in an intensified mode, which can lead to its overheating and breakdown.

In addition, there is a risk of moisture on the conductive elements of the device, as a result of which a short circuit is possible or with an electric shock performing a human defrosting.

ATTENTION! Shtepsel fork, after extracting it from the outlet, is also advisable to put on some elevation so that droplets of water during work do not accidentally fall on the part.

Free

At the next stage, remove all the products stored in it, containers with food and place them in a cool place from kitchen appliances.

Even if the refrigerator has very little hoarfrost and it does not take a significant amount of time to remove it, there is a risk that even in such a short time the food will have time to deteriorate.

The temperature of the products in the unit is low, therefore, if you leave food in the chamber during thawing, food will “give” the cold into the surrounding space, thereby slowing down the process of defrosting.

Pull the boxes, pallets and gratings

After extracting the products, remove all the boxes for vegetables, fruits in the refrigerator, containers for eggs, shelves, gratings.

This will be much easier to carry out to eliminate pieces of melting ice, and do not forget that all removable elements of the refrigerator also need regular cleaning.

ADVICE! While the household appliance will be thawed, you will have time to wash all the extracted details.

Determine the drainage hole

All models of refrigerators are equipped with a drainage system, which is necessary to divert moisture formed as a result of hoarfrost on the evaporator. The water drain hole is located at the bottom of the rear wall of the refrigerator compartment.

In devices with the No Frost system, it is located behind the protective panel in the lower part of the rear wall of the refrigerator compartment.

In the process of thawing, a large amount of moisture will form. In order for the liquid to freely leave the chambers. be sure to check the condition of the drainage opening, in case of clogging. clean the drain with a special ruff or pick up warm water into a one.time syringe and pour it into the stock with force.

You can find out how to clean the drainage hole in the refrigerator here.

Prevent flooding

During the defrosting, melt water can go beyond the chambers. In order not to arrange a flood and not spoil the flooring. put the old towels, newspapers around the refrigerator, place rags at the bottom of both cameras.

REFERENCE! In many devices under the freezer, there is also a drainage tube that can be slightly advanced and lower its end into the bowl.

Remove the ice

Do not wait until the ice under the influence of warm air will completely turn into water.

As soon as you notice that the hoarfrost easily moves away from the inner surfaces of the compartments. moisten a soft sponge in warm water and with its help with neat movements, without effort, remove a thin snow crust, collect ice from the bottom.

Wipe the resulting water

At the end of the melting with a dry rag or towel, wipe all the inner surfaces of the refrigerator, check the drainage hole again.

ADVICE! Carefully inspect the space around the kitchen device for water, if necessary, be sure to remove moisture.

Wash the refrigerator

After defrosting, you can proceed with the washing of the internal and external parts of the device.

Evaluate the degree of contamination of your device: with minor accumulations of fat, dust make a weak soap solution (1-2 teaspoons of liquid detergent for dishes dissolve in a glass of water) and wash the walls.

After processing with a cleaning drug, wipe the surface with clean water and dry them with a towel.

If you are interested in how to wash the refrigerator No Frost, read this publication.

IMPORTANT! Before starting the thawing procedure, put a little refrigerator forward or to the side so that after defrosting you can wash the back wall of the device.

Leave to dry

After defrosting and washing, leave the door of the electrical appliance for some time open so that all the surfaces are completely dry.

If your refrigerator with a manual type of thawing or drip-after drying, close the door, turn on the device and install boxes, containers and shelves in your previous places after 1.5-2 hours, load the products.

The equipment with the No Frost system will have to leave in the disconnected state for at least 12 hours, and preferably for a day.

IMPORTANT! Ignoring the rules on the procedure for turning on the refrigerator with No Frost can lead to the failure of the “heart” of the kitchen device. compressor and electric motor.

Liebherr refrigerator problems (Liebherr). Articles of Friz-Service company

It happens that the Liebherr refrigerator stops working. In this case, you must try to find the reason for its failure.

Basically, all modern household appliances on the display are highlighted by an error code, however, there are no this function in some models, so you need to understand what the malfunction is.

The refrigerators of this brand are reliable, they are quite expensive, they undergo hard quality control in production, but sometimes, when they are included in the network, they do not want to work at all.

Does not turn on

You can face a situation where electronic mechanisms work, light bulbs burn, but the unit starts for a short period of time or does not turn on at all. In this case, most often one of the reasons may be a breakdown of the starting relay, there are no clicks, it does not even try to start. If after starting the equipment quickly stops, then the matter is in the compressor.

The absence is evidenced by the absence:

First of all, you should check if the outlet itself works directly, and see how tightly the fork entered it. The refrigerator will not turn on if an electric cord is torn off in any place. To check its integrity, you need to use the multimeter.

Hook and ice crust

The formation in the freezer of the snow plane to the door to the door, and ice is also observed along the edge, indicates that it closes loosely. The reason is the curvature or the whole thing in the seal. And then on the side surfaces of the refrigerator, you can observe intentions. If the formation of a snow growth on a wall located behind, then the reason must be sought in the thawing sensor or evaporator.

The mismatch of the temperature regime

Sometimes inside the freezer or refrigerating chamber the temperature parameters do not meet those that are currently exhibited. You can talk about the breakdown of the compressor when it is turned off or turned on for a split second, while the temperature is significantly greater than it is set. If cold air is felt throughout the closed door, and inside the unit is warm, then the sealing gum does not fit tightly.

The frequent operation of the compressor indicates the leakage of the refrigerant, however, at this time the cameras do not cool. When ice is formed on the wings of the fan, which is equipped with the Nofrost system, then the bearing is jammed or the malfunction must be sought in the engine.

The temperature of the unit can increase if it is high and in the environment. This must be monitored, because in addition to the fact that the products will spoil, the compressor will also have to turn on, and this will lead to its quick breakdown. When compressors operate rapidly, and the freezer freezes strongly and the temperature is very low everywhere, we can say that the reason is in the temperature sensor or regulator.

High noise

Due to the presence of mobile mechanisms in this household technique, it cannot work without noise. With normal functioning, different elements make various types of sounds:

Nofrost system fans calmly and monotonously buzz;

The inclusive and disconnected compressor relay produces clicks;

During the flow of gas, gurgling is heard;

The compressor makes a monotonous rumble when working.

Liebherr noise indicator is not high. approximately 40 dB. With a more loud noise, you must first check the slope using the level, and also make sure that the unit is at some distance from the furniture and walls.

An irregular and rattling sound appears in the refrigerator if standing, for example, bottles are in contact there. Also, the reasons may be a weak mount or compressor malfunction. The bearing broken in the fan leads to the appearance of this kind of sound.

Water under and inside the refrigerator

When the drainage system clogs, the water will accumulate at the bottom of the camera. It is not difficult to cope with this malfunction yourself, it is advisable not to postpone it for later. Water under the unit on the floor may appear if a drainage tube is shifted, aimed at a special container. In this case, unscrew the panel located at the back at the bottom, where the compressor stands, and return the tube to the correct position.

A situation may arise when the bath cannot accept the water entering it due to its large amount. This occurs with a breakdown of a fan or evaporator. When water appears on the front surface of the technique, it means that the door does not close tightly. You need to correct its position or repair the seal. It is extremely rare that water is assembled under the refrigerator Liebherr due to damage to the collection for the liquid. It is changed to a similar container, fixed with self.tapping screws.

No light

Although it is quite possible to do in the absence of light in the refrigerator, it is still better when it is there. The reasons for such a malfunction is:

Sometimes a light bulb begins to blink. This can happen due to a compressor breakdown or temperature reduction due to leakage from the insulated area or broken sensor. You need to change the necessary sensors.

Repair of systems and parts

Experts note that the components of refrigerators of this brand in rare cases need repair, since their quality is very high. Most often they break if they are incorrectly treated, or under the influence of external circumstances. It is not always possible to repair with your efforts, it also applies to their replacement. The best option is to contact a specialized center.

Gas leak

In those areas where the copper and aluminum parts of the circuit are soldered or cooked, the refrigerant is most often flowing down. When the damaged place is in the wired area of ​​the unit, then there the plastic is swollen and darker is done. It is required to contact specialists who work in this field.

Launching relay

Extremely rarely in the refrigerators of Liebherr breaks the starting relay. This happens if:

Repair can be carried out in a special service workshop. The mechanism will have to replace the mechanism when the problem associated with the winding occurs.

Fan in the No Frost system

The fan in the Liebherr refrigerator is located behind the evaporator. It is separated from the camera with a special lid that has a hole. To remove it, you need to turn the mounts 90 degrees. When the engine is turned off, the unit must be turned off. This simple design is repaired in a workshop that establishes household appliances. Most often, you have to change the bearing in the fan or repair the ragged wiring.

The temperature sensor for the refrigerator: device in Liebherr and other refrigerators

Refrigerator is a device that allows you to maintain a low temperature inside its compartments. There is in every family, and we do not imagine our life without him, so firmly he entered her and stayed there forever.

For thousands of years, rooms filled with ice were used to preserve the freshness of food, until in 1803 one American did not demonstrate the first prototype of the refrigerator. This can be safely called the beginning of a new era of storage of products.

Today, this device is commonplace, it has it in every house, and some have several at once, but few people wonder. what is the refrigerator and how it keeps our food?

The device is a refrigerator

  • compressor (motor). the main part of any refrigerator that provides the circulation of freon (coolant) through the system;
  • capacitor. removes the heat formed from the evaporation of the freon to the environment;
  • evaporator. a cooling apparatus, which occurs due to boiling of a liquid freon;
  • capillary tube. reduction of pressure in the system;
  • Filter-dryer-as can be seen from the name, its purpose is to protect from blockage;
  • a complementar. a container for finishing a liquid freon;
  • Thermallera is also one of the most important moments in the uninterrupted functioning of the refrigerator, due to which the necessary temperature inside it is maintained. It is worth talking about this system separately.

The refrigerator thermostat

As mentioned above, the thermostat is a device that helps control the level of cold inside the refrigerator. With the help of a thermal attenter, he reads the temperature and sends the signals to the compressor, forcing it to turn on if the refrigerator has become warmer than necessary, and turn off if, on the contrary, it froze.

Everyone who is familiar with the old models of refrigerator chambers remembers the moment when they began to growl, and then suddenly stopped. Or just loudly snapped, including or turning off cooling, which was sometimes soarly scared. Fortunately, modern models do not have such problems, since they work completely silently.

It is located depending on the model of the refrigerator. In the older ones where the temperature level was exhibited using a mechanical regulator located inside the chamber, the thermostat is located there, inside. In newer models, where the regulator is located outside the housing, is equipped with a mass of new data, capabilities, switches and screens, the thermal attempt is located, respectively, from the outside. As a rule, this whole system is located in the upper part of the refrigerator door.

Modern models of refrigerators can have several temperature sensors at once. For example, in some Liebherr refrigerators there are four of them, and they are located in the following places. in the freshness zone (a special compartment for preserving the freshness of vegetables and fruits), in the freezer, in the refrigerator itself, as well as on the evaporator.

The thermostat consists of two parts. the temperature sensor for the refrigerator and contacts that close or open depending on that at this particular moment it is necessary. to start cooling or stop.

Thermal attenter is a part of the system aimed at reading the temperature in the refrigerator to the registrar system, which, in turn, sends this data to the compressor.

What happens if the temperature sensor breaks?

The consequence of the failure of the thermal attemptor is incorrect reading of the temperature, the result of which is a failure in the work of the motor. In short, this can be explained as follows. the broken sensor fixes warming in the refrigerator, which, in fact, works well.

As a result, the compressor begins to function constantly intensively, which is why, firstly, a decrease in temperature and freezing of products occurs. And secondly, which is already more serious than ice cream carrot is a compass wear that will ultimately lead it to breakdown.

Frost camera

Freezer. a device that stores and freezes products. The optimum temperature in a regular chamber should be from.15 to.18 degrees. In some cases, the temperature may be higher or lower, but this already applies more to the exceptions from the rules.

Increasingly, people began to purchase this type of household appliances, since almost everything can be frozen in the freezer, starting with meat and fish products, ending with strawberries and other berries. After all, it is good to get several berries in the middle of winter and make yogurt or any dessert out of them. But for the freezer to be really high.quality, you need to choose a good manufacturer, which is a very famous company Liebherr.

Manufacturer Liebherr

For an ordinary consumer, this company is a regular company that manufactures refrigeration and freezers. But this is only a small part of what this German concern produces. Liebherr manufactures: construction equipment, port equipment, special equipment, career dump trucks and so on.

Therefore, you can be sure that the household appliances that this huge concern produces is made really high quality and for many years. Almost every city has a service center where you can order the necessary parts, in the case of a breakdown of equipment, service managers will repair the freezer “Liebherr” free of charge. However, the breakdown of household appliances from this company is extremely rare.

Popular models

To date, there are more than thirty species of varieties of freezers of this manufacturer, so it makes no sense to talk about each of them. But there are several of the most popular models that deserve special attention of consumers.

Liebherr 1223 freezer is a small camera with a useful volume of 98 liters. She has three plastic drawers. There is a temperature control and cold indicators. When you turn off the electricity, if you do not open the doors, holds its temperature up to 26 hours. It has all the standard functions: Super Frost, Frost Safe, Smart Frost.

Liebherr 1376 freezer has four food storage boxes. However, when electricity is turned off, the device retains its temperature for a whole 30 hours. But you need to defrost the camera yourself, there is no automatic defrost functions. Quite reliable and very popular freezer “Liebherr“. The price of this model is about 500.

The best.selling models also include such chambers:

The main difference between these cameras is the useful volume and number of boxes. The functionality of all freezers is approximately the same.

How to use a freezer

Despite the fact that each freezer has its own operating instructions, there are still general rules for use.

  • When you turn off the device from the network, you must hold on to the fork, you do not need to pull the wire;
  • You can not use a freezer with a damaged network cord;
  • It is forbidden to independently repair the device, this should be done by specialists;
  • damage to the refrigerant contour is not allowed;
  • Near the device you can not put candles, lamps and other hot objects that can cause a fire;
  • Store alcoholic beverages or alcohol only in tightly closed containers, alcohol, which accidentally spilled, can come into contact with an electric node and ignite.
  • Liebherr freezer should be on a horizontally flat surface;
  • It is impossible for a gas stove near the device or the sun’s rays directly fall;
  • We recommend putting the camera so that its back wall is near the wall;
  • It is necessary to move the device only in unloaded state;
  • align the camera exactly in level, for this it is necessary to adjust the supports that are below.

Field of application of freezer chambers Liebherr

Liebherr freezer is used only to freeze food in home or as close as possible to home conditions. It is forbidden to use the device for industrial purposes.

The chamber also cannot be stored pharmacy, blood plasma or other laboratory accessories. The freezer cannot be placed in too cold or hot places. The technique can work normally in the range from 5 to 42 degrees. Otherwise, the freezer may fail. Germany, Liebherr in particular, does everything possible to expand the scope of household appliances.

Built.in freezers

In modern kitchen design, you can’t do without innovative Liebherr technique. The built.in freezer is perfectly enters the countertop, thereby you can save additional square meters.

Thanks to the well-thought-out development, the entire equipment has an additional ventilation system, so there is no need to make any ventilation gaps in the countertop. Built.in freezers have a fairly high price, but to achieve excellent design and savings, this amount does not seem to be large.

The built.in freezer UIG 1313 has 97 liters of useful volume and electronic control. Such a freezer is small enough and harmoniously embeds into the countertop.

Another built.in freezer model is SIGN 3556, its useful volume is 210 liters. It is built into furniture and takes the form of a conventional cabinet. At the same time, the class of energy consumption A, this means that this freezer is quite economical, despite its size.

defrost, drip, refrigerator, liebherr, chamber, done

Freezing products

The temperature inside the chamber depends on the door opening frequency, the number of products, the ambient temperature in which the Liebherr freezer is located. The instruction will be that the recommended temperature inside the camera should be.18 degrees.

The electronic temperature controller has a step of 1 degree, from.14 to.28 degrees. The instructions of each model of the freezer indicate what maximum number of products can be frozen within a day. As a rule, the weight of frozen products is from 10 to 15 kilograms for small cameras with a useful volume of up to 100 liters.

In almost all models of Liebherr freezers, there is a Super Frost function, which freezes products as quickly as possible. When “super frosts” is turned on, the freezer begins to work on its maximum capabilities. It is needed only for quick freezing of products, to turn it on when an already frozen product was supposed, it is not recommended.

Liebherr (Liebherr) refrigerator does not work, reasons

If your Liebherr refrigerator does not work, you do not need to despair. you need to look for the cause of the breakdown. Modern technique can highlight the error code on the display, but if there is no one, we will help you understand the malfunction.

Liebherr refrigerators have created an expensive and reliable house for the home that passes strict quality control, only when included in our network begins to fail. Consider why this is happening.

Typical problems of the Liebherr refrigerator

The more technologies and electronics are introduced into domestic equipment, the more sensitive it is to problems in the network. Incorrect installation and operation contribute to the work of HO “Liebherr”. Let’s see what breakdowns users most often complain.

A refrigerator does not work in the refrigerator

The compressor is buzzing, but there is no cold in the cell? You need to take measures. Due to overloads, the freezer can also fail, which will lead to expensive repair. The problem is storage of products, because with a faulty refrigerator they will quickly deteriorate.

  • Is the camera door tightly closed. Due to the overflowing department, the closure of the door can interfere. Move away pots and soda.Check the door seal. If it does not fit the case, it must be replaced or put in order. Hot water will help straighten the rubber, restore its shape. Water the seal around the perimeter from the teapot, immediately straighten.
  • Check the temperature regime in the chamber. When the room is hot, the maximum temperature is installed in the refrigerator, the compressor does not cope with the load. Reduce the readings. stop on the division of 2.5.
  • Inspect the fan if you have no frost cooling system. When the fan does not work and ice forms on its blades, you need to urgently defrost the refrigerator. In No Frost, the fan is responsible for the distribution of cold air through the chamber.

Defrosting did not help to resume the work of technology? So, it’s a malfunction. You can determine the breakdown by external signs:

defrost, drip, refrigerator, liebherr, chamber, done
  • After defrosting the camera, the fan did not start working. Check its motor. it may be burned and you need to replace.
  • In addition to the fact that the fan blades do not rotate, a snow coating was formed on the walls of the department. The wall was most very frozen, behind which the evaporator is located. The heater of the evaporator is faulty, the rewinding in the refrigerator does not turn on. Therefore, snow and ice accumulate on the walls.
  • The freezer is badly freezed, the walls are overgrown with ice. The motor-compressor works without rest. Signs indicate problems with the temperature regulator in the freezer, so cold air is not pumped into the refrigerator.
  • Refrigerant leaks may be accompanied by bloating. If the leak occurs through a steel circuit, rust in the case will be visible. With mechanical damage to the wall, gas is also possible. The specialist will help to eliminate the leak and refuel the system with freon.
  • Damage to the thermostat or air sensor of the refrigerator compartment. Therefore, the board does not receive a signal about the temperature, so the cooling does not turn on. We need a replacement of details.

Take a closer look at your refrigerator. Perhaps such signs will help you find a problem.

The freezer does not work in the refrigerator

Since we are not looking at the freezer so often, you can not immediately notice a malfunction in work. However, if blocks of ice intended on the walls of the camera, and a puddle of water was gathered nearby, you need to be wary of.

Immediately check the density of the door extension. If he passes warm air, then the system will compensate for the temperature increase. When the compressor is turned off, the intended snow will begin to melt.

It also happens that the freezer does not work at all. Then pay attention to the signs of a breakdown:

  • The freezer engine works for a few seconds and turns off. The compressor is faulty. As a result of the exceeded load, rapid wear of the motor parts occurs, so you will need to replace the device.
  • The engine works normally, but after disconnecting it does not start for a long time. This indicates problems with an air sensor or a temperature regulator. The electronic module does not receive information about the temperature in the chamber, so it does not give a command for cooling.
  • If the switching valve is jammed, then the freezer will poorly cool the products, because the power for normal freezing is not enough. We need a valve replacement.
  • With a gas leak, it becomes smaller, so it is not enough for the normal operation of the system. You need to eliminate the leak and season the system by freon.
  • With a breakdown of the control module, additional features may not be. The camera may not work, the light and lights on the panel. do not burn. Probably, the breakdown happened due to a short circuit, which damaged the elements of the board or its wiring. The master will conduct diagnosis, replacement or flashing of the module.

To accurately decide on the causes of the problem, there are few external signs. It is necessary to carry out full diagnosis of technology.

The refrigerator works loudly when turning on

The loud work of the refrigerator not only interferes with the user, but is also able to harm the technique. If you are convinced that noise values ​​exceed the norm, start searching and eliminating the problem.

  • Correct installation. When the housing is overwhelmed, an additional load lies on the engine, which makes it work with a vengeance and noise. Set the HO in level, adjust the position of the legs. The technique should not stand close to the wall, battery or other furniture.
  • Transport bolts. If you only brought and installed the equipment, you may have forgotten to remove the bolts that fix the position of the motor. It is necessary to remove them, otherwise it will lead to wear of the details.
  • The location of the dishes. Probably the rattle of dishes on the shelves when two containers are in contact. Change the location of the pan.
  • The intention of snow and ice on the walls of the department leads to a doubled work of the motor. If the intention occurs on one wall, the case imbalance occurs. For this reason, the refrigerator can buzz and jump when turning on. It is necessary to carry out full defrosting of equipment within 10 hours.
  • Drowned engine mounts. Since shock absorbers serve to absorb vibrations, when weaken their fasteners of the rumble and rattling the compressor, they are poorly drowned out. You need to tighten the fasteners.

How to defrost Liebherr refrigerator or freezing camera?

One of the difficult procedures for every housewife in the house is to defrost and clean the refrigerator. Therefore, Liebherr made sure that the hostesses had less time for this process.

Thus, a system of automatic defrosting of the refrigerator or a system was created or

However, despite the relief of such a process, manufacturers did not completely save the owners of the refrigerator from manual cleaning.

Cleaning in freezer and refrigerator is needed to disinfect accumulated bacteria. So, the owner of the refrigerator will not only get rid of poor smell, but also retain himself from all kinds of diseases.

If we talk about the fur coat of hoarfrost formed in the cell, then it does not bring much harm, but creates two inconvenience: it creates a decrease in cooling functionality and occupies excess volume in the cell. There is also a threat of damage to some parts in the refrigerator.

The formation of a “fur coat” depends on factors such as the level of humidity in the room, the temperature regime and the degree of sealing the refrigerator.

Defrosting the refrigerator should begin at the moment when the hoarfrost interferes with the occupied volume of product laying, or the boxes inside the freezing camera are already difficult to pull out or insert.

So, let’s start defrosting:

First you need to free the refrigerator from the food in it. All frozen foods are transferred to plastic or metal dishes, and put into the cooler place in the apartment or in the house.

You need to turn off the refrigerator or Liebherr freezing camera from the network and open the door.

Although the refrigerators are equipped with tari for filling the condensate from hoarfrost today, but still a rag to soak excess moisture, which did not fall into the container, lies up to the bottom of the camera.

It is forbidden to remove ice by hand. So the owner can damage the entire mechanism of freezing and cooling products.

It is not advisable to allow water overflow in the capacitance of condensate, if the water began to flow out of the container, this can affect the rest of the refrigerator and eventually lead to the appearance of rust.

After complete thawing, the refrigerator is wiped with a dry rag.

To reduce the speed of hoarfront, the rear wall of the refrigerator can be wiped with glycerin.

It is not advisable to defrost the refrigerator in hot weather. It is better to do this when it is cool, since it will be difficult to gain the desired temperature to the unit.

Methods to speed up the process

It is forbidden to accelerate the defrosting of refrigerators. this is indicated in the instructions for any model “Liebherr”. But there are situations when there is a catastrophically not enough time for thawing. nowhere to store products or you need to urgently leave the house. In this case, you can use the methods of accelerated defrosting:

  • Place containers with hot water in the refrigerator. basin, pots, bottles and rubber heating pads.
  • Spray the inner walls with hot water from a spray gun.
  • Turn on the hairdryer for average power and manually blow the plots with ice.
  • Put the heat.cognrator opposite the camera, turn on and direct the stream in the “problem areas”.

It is forbidden to break off and scrape off pieces of ice from the walls. you can damage the coating, and the refrigerator will fail!

Liebherr refrigeration equipment is produced in Germany. The company itself values ​​its impeccable reputation, therefore it provides its customers with a long guarantee for service. With a breakdown in the first 3 years of operation, the repair is provided by the manufacturer through service centers. which are located in large cities. In the case of a factory marriage (sufficiently rare), the manufacturer changes the unit for a new.

The possibility of free repairs can be canceled if the consumer is not observed by the standards for the use of technology. All of them are described in the instruction manual. Independent interference in the operation of the device (its repair and maintenance) in the warranty period. prohibited. If the factory soldering (seals) is violated, the warranty card is recognized as invalid. Compliance with all operating requirements will help protect the refrigerator from the breakdown, and the user will save from additional repair costs.

Independent repair of the Liebherr refrigerator

Liebherr refrigerators. Select and buy Liebherr refrigerator.

  • STINOL refrigerators instruction manual. download the general instruction StD 125 download instruction Stn 167 / Stinol STS 167 download instruction STN 185 / STINOL STN 185 D Download instructions STN 200 download.
  • The operation of BEKO refrigerators according to the instructions. Beko has long become one of the leaders of the domestic household appliance market, including refrigeration equipment. Devices of this production differ relatively small.
  • Operation of the Oka refrigerator according to the instructions. the refrigerator is the most popular household device, without which it is difficult to do to modern man. Now modern units of Samsung, Liebherr.
  • Saratov freezer: operating instructions. the refrigerator technique produced by domestic manufacturers has established itself as a high.quality, reliable and corresponding to the declared functionality. Overview of her models.
  • Atlant refrigerators instructions. the service life of a new refrigerator depends on the quality of production and its proper operation. Therefore, before starting to use household appliances, you need to carefully study.
  • The instruction manual for a two.chamber refrigerator Minsk. the first refrigerator Minsk was released in 1962. At a factory located in the capital of Belarus. He is currently part of. which specializes in.
  • Samsung refrigerators instructions and setting up Samsung refrigerators have long been in high demand among consumers around the world, including in the CIS countries. Such popularity of this species.

How to defrost Liebherr refrigerator two.chamber instruction

In order for the refrigerator to work properly and there is no unpleasant odor from it, the master recommends to defrost it at least once a year.

The main stages of defrosting the refrigerator:

  • Disconnect the refrigerator from the mains.
  • Free the refrigerator from the products.
  • If possible, remove all shelves and containers and wash them separately.
  • Leave the refrigerator with open doors until the ice is completely thawed.
  • Wash the refrigerator with a soft rag moistened with a special remedy for washing refrigerators or a dishes for washing dishes.
  • Wipe the refrigerator dry and containers and shelves taken out of it.
  • Place the shelves and containers back into the refrigerator.
  • Close the doors and turn on the refrigerator in the mains.
  • Upon reaching the optimal temperature in the refrigerator and freezer, download products in them.

Features of defrosting

All Liebherr brand products are highly quality and the use of the most modern technologies. To simplify the refrigerator care, the developers used several convenient innovations:

  • Nofrost technology. This is a professional cooling system that prevents the formation of hoar on the walls and on the products stored in it. According to the manufacturer, you do not need to defrost the refrigerator. However, practice shows that over time, without complete defrosting in the freezer, an irrigation can increase, and an unpleasant odor will appear in the refrigerator.
  • Safetyglass. durable and easy to care for glazing. All shelves of the refrigerator are made of high.quality glass without sharp corners, which is easily washed, is resistant to scratches and increased impact resistance.
  • Quickly outgoing containers and shelves
  • Smartsteel. a special coating that makes fingerprints not noticeable, protects the case from scratches and facilitates care

How to save products in the freezer while defrosting is going on. At a certain moment, ice is formed and it becomes difficult to extract a container from the freezer. This means it’s time to defrost her. We will offer several useful tips on how to quickly get rid of ice in the cell.

Is it mandatory to defrost the freezer?

With a constant opening of the refrigerator door and when we put the products into it, moisture penetrates inside. It systematically settles on the walls of the freezer, while converted into ice, thereby complicates the extension of the shelves with products.

The more time the refrigerator does not defrost, the more significant the consumption of electricity.

Due to the fact that ice is formed on the walls, it is necessary to use more electricity in order to control the temperature set in the freezer.

How to defrost the refrigerator

Refrigerators today do not require frequent defrosting. Modern cooling systems make it possible to defrost 1-2 times a year. The presence of No Frost in the refrigerator involves only regular washing the unit sections. ice will not form.

How to properly conduct a defrosting procedure so as not to spoil the refrigerator?

Defrost correctly

The general instructions for defrosting the refrigerators are as follows:

  • Disconnect from food. Temperature controller to digit 0. The door is completely open;
  • Free all sections from products. After that, pull out all the lattices and trays;
  • Remove talus water. As a rule, it is collected in special trays. If the container is absent, then you can use a pallet or bowl;
  • Defrosting procedure. Leave the door open and after a while the ice will thaw.

Some models of refrigerators should be defrreded taking into account the characteristics of the systems built into them.

Atlant

The freezer section is divided into three parts: the lowest temperature remains in the upper sector.

The compartments in the refrigerator are separated by partitions. Along one of them is a cooling pipe.

Ice is collected on it and does not melt. Properly defrost Atlant and remove ice from this place.

Any model of the refrigerator must be washed, disconnected from power.

Indesit

New Indesit models can be defrosted 3-4 times a year. To correctly defrost Indesit under the drain hose, which is present in new models, you need to place a basin or tray. In the case of a two.chamber unit, each section is defrosted separately. The section that will defrost is disconnected.

Do I need to defrost models with the no frost option? Manufacturers recommend carrying out the procedure several times a year. Defrost will not take more than two to three hours. The refrigerator after thawing must be thoroughly washed.

Biryusa

It is recommended to place pots with heated water in the freezer and under it. After that, close both sections for 5 minutes.

At this time, ice will begin to melt. Under the refrigerator, place rags for collecting water in advance.

It is better to defrost the old model twice a year or more, depending on the degree of ice.

With uninterrupted power supply, the refrigerator with the No Frost system is independently redesigned to defrosts after a certain number of inclusions. The number of inclusions is set in the settings. With unstable power supply, independent defrosting may not be activated. Defrosting the unit with a mixed system is performed manually. Defrost only one selected compartment.

Liebherr

The built.in No Frost system in Liebherr does not imply defrosting the freezer, since ice does not form. The fan in the freezer periodically turns off and the heater is activated. Melt water flows into a special compartment and evaporates. It is recommended to clean the refrigeration and freezers once a year.

Stinol

Both old.style models and options with the No Frost system are available.

The brand is very easy to maintain. It is recommended to check the evaporator for the formation of ice.

The ice on the evaporator slows down the air exchange in the chamber.

In the process of defrosting, they see that the water does not spill out of the chamber over the edge.

This can lead to corrosion of some elements. The refrigerator can only be turned on after thorough processing of the compartments with a dry rag.

Hotpint Ariston

HotPoint Ariston is a refrigerator with NO Frost in both chambers. Defrosts manually. The defrosting procedure takes several hours. 4 hours after turning on the compartment, you can fill in products.

The refrigerator compartment is thawed on its own. In the process of working on the rear wall of the unit, a layer of ice at 7-8 mm is assembled. This is a normal phenomenon associated with the functioning of the cooling system. The formed ice is removed using a system of automatic defrosting on the rear panel of the refrigerator.

Beko freezer is just defrosting: melt water flows into a special compartment. It is recommended to defrost the refrigerator twice a year.

Samsung

Models of this brand in the absence of the No Frost system should be defrosted within 14-24 hours. After defrosting, the device is connected to the network and left empty for two hours.

Saratov

The manufacturer recommends a defrosting as often as possible. It is advisable to do this monthly. Defrost is carried out taking into account the drip system, which guarantees an absolutely silent process. During the defrost, condensate is collected, which must be collected in a timely manner.

Whirlpool

Models with the No Frost system are recommended to defrost completely at least once a year. If there is one evaporator in the freezer compartment, it is normal that within 24 hours after the procedure, it is slightly defrosted. For the freezer, the temperature regime should be set: minus 16-18 degrees.

Electrolux

In all Electrolux models, an automatic defrosting system in refrigeration edema is configured. You can defrost the freezer, unless it is activated by the No Frost option. The formation of a layer of ice and the regularity of the procedure will depend on the features of the use of the unit.

When the snow cover appears on the internal surfaces and on the frame of the fridge, it is removed with a spatula at any time. This procedure is in no way connected with the defrosting of the freezer. If the resulting layer of ice is 3 mm or more, then the refrigerator is defrosted. The freezer compartment is defrosted for preventive purposes 3-4 times a year.

Models of the automaton suggest the corresponding inclusion of the defrosting mode.

A switch is set between the refrigerator door and the freezer, which includes heating this element with a heater.

In models with a manual defrosting system, the switch turned on the thawing mode with a loud click behind the unit.

In the semi.automatic versions of the brand, the jumper does not change the situation until the process of defrosting is going on. After that, the switch returns to its place.

Drip

Transportation without defrosting of refrigerators with a drip system is allowed by the manufacturer. After transportation, the unit can be immediately enabled. It is not recommended to immediately turn on the technique only if the temperature during transportation was below 0 degrees: condensation may form. After it evaporates, the unit can be connected to the network.

Defrosting the refrigerator in stages

You can start washing the refrigerator, when the temperature has become a little warmer, but to clean the freezer you need to wait until there is ice left in it. There are options for quick defrosting, but it is better to give the opportunity to the natural process.

  • Wash the taken shelves and containers, put them dry.
  • Soak puddles with a dry rag and capture the rest of the garbage.
  • Wet the napkin with soapy solution, carefully walk inside and out. In this case, the powders and abrasive products should not be used so as not to scratch the surface.
  • Rinse the drain hole if it is a drip of defrosting system.
  • Clean the dirt between the folds of the rubber.
  • Then wipe everything dry.
  • We go to the freezer. remove the broken ice and snow, pour liquid from the pallet, survive a rag.
  • After the ice growth, repeat the cleaning procedure in the freezer.
  • Put clean shelves and trays.
  • Close the door tightly.
  • Turn on the cord in the outlet.
  • Wait 30 minutes and only then return the products to the refrigerator.

Here is a detailed video instruction on how to defrost a two.chamber refrigerator:

Defrost correctly

The general instructions for defrosting the refrigerators are as follows:

Freezer Defrost Drain Is Frozen — Freezer Troubleshooting

  • Disconnect from food. Temperature controller to digit 0. The door is completely open;
  • Free all sections from products. After that, pull out all the lattices and trays;
  • Remove talus water. As a rule, it is collected in special trays. If the container is absent, then you can use a pallet or bowl;
  • Defrosting procedure. Leave the door open and after a while the ice will thaw.

Some models of refrigerators should be defrreded taking into account the characteristics of the systems built into them.

Atlant

The freezer section is divided into three parts: the lowest temperature remains in the upper sector.

The compartments in the refrigerator are separated by partitions. Along one of them is a cooling pipe.

Ice is collected on it and does not melt. Properly defrost Atlant and remove ice from this place.

Any model of the refrigerator must be washed, disconnected from power.

Indesit

New Indesit models can be defrosted 3-4 times a year. To correctly defrost Indesit under the drain hose, which is present in new models, you need to place a basin or tray. In the case of a two.chamber unit, each section is defrosted separately. The section that will defrost is disconnected.

Do I need to defrost models with the no frost option? Manufacturers recommend carrying out the procedure several times a year. Defrost will not take more than two to three hours. The refrigerator after thawing must be thoroughly washed.

Biryusa

It is recommended to place pots with heated water in the freezer and under it. After that, close both sections for 5 minutes.

At this time, ice will begin to melt. Under the refrigerator, place rags for collecting water in advance.

It is better to defrost the old model twice a year or more, depending on the degree of ice.

With uninterrupted power supply, the refrigerator with the No Frost system is independently redesigned to defrosts after a certain number of inclusions. The number of inclusions is set in the settings. With unstable power supply, independent defrosting may not be activated. Defrosting the unit with a mixed system is performed manually. Defrost only one selected compartment.

Liebherr

The built.in No Frost system in Liebherr does not imply defrosting the freezer, since ice does not form. The fan in the freezer periodically turns off and the heater is activated. Melt water flows into a special compartment and evaporates. It is recommended to clean the refrigeration and freezers once a year.

Stinol

Both old.style models and options with the No Frost system are available.

The brand is very easy to maintain. It is recommended to check the evaporator for the formation of ice.

The ice on the evaporator slows down the air exchange in the chamber.

In the process of defrosting, they see that the water does not spill out of the chamber over the edge.

This can lead to corrosion of some elements. The refrigerator can only be turned on after thorough processing of the compartments with a dry rag.

Hotpint Ariston

HotPoint Ariston is a refrigerator with NO Frost in both chambers. Defrosts manually. The defrosting procedure takes several hours. 4 hours after turning on the compartment, you can fill in products.

Refrigerator Will Not Defrost. Top 6 Reasons & Fixes. Kenmore, Whirlpool, Frigidaire, GE & others

The refrigerator compartment is thawed on its own. In the process of working on the rear wall of the unit, a layer of ice at 7-8 mm is assembled. This is a normal phenomenon associated with the functioning of the cooling system. The formed ice is removed using a system of automatic defrosting on the rear panel of the refrigerator.

Beko freezer is just defrosting: melt water flows into a special compartment. It is recommended to defrost the refrigerator twice a year.

Samsung

Models of this brand in the absence of the No Frost system should be defrosted within 14-24 hours. After defrosting, the device is connected to the network and left empty for two hours.

Saratov

The manufacturer recommends a defrosting as often as possible. It is advisable to do this monthly. Defrost is carried out taking into account the drip system, which guarantees an absolutely silent process. During the defrost, condensate is collected, which must be collected in a timely manner.Information. The duration of the procedure depends on the collected layer of ice. If the refrigerator did not defrost for a long time, then it is turned off and left open for the whole night.

defrost, drip, refrigerator, liebherr, chamber, done

Whirlpool

Models with the No Frost system are recommended to defrost completely at least once a year. If there is one evaporator in the freezer compartment, it is normal that within 24 hours after the procedure, it is slightly defrosted. For the freezer, the temperature regime should be set: minus 16-18 degrees.

Electrolux

In all Electrolux models, an automatic defrosting system in refrigeration edema is configured. You can defrost the freezer, unless it is activated by the No Frost option. The formation of a layer of ice and the regularity of the procedure will depend on the features of the use of the unit.

Important! The frequency of door opening and high humidity in the room are reflected in the process of ice formation.

When the snow cover appears on the internal surfaces and on the frame of the fridge, it is removed with a spatula at any time. This procedure is in no way connected with the defrosting of the freezer. If the resulting layer of ice is 3 mm or more, then the refrigerator is defrosted. The freezer compartment is defrosted for preventive purposes 3-4 times a year.

Models of the automaton suggest the corresponding inclusion of the defrosting mode.

How to defrost the refrigerator. step.by.step instructions from 7 poucts

After different intervals of time, from about 2 months to a year, a layer of ice begins to form on the inner surface of the refrigerator. This phenomenon reduces the effectiveness of the equipment and makes it difficult to operate. Therefore, periodically you have to independently defrost the formed ice.

This article is universal, suitable for one or two-chamber, three-chamber models of foreign and (Soviet) production: HotPoint Ariston (Hotpoint Ariston), Ardo (Ardo), Beco (Bosch), Bosch (Bosch), Candy (Kandy), Daewoo (Daewoo). Electrolux (Electrolux), Gorenje (Gorenje), Haier, (Hyer), Hansa (Hansa), Hitachi (Hitachi), Indesit (Indesit), Liebherr (Liebherr), LG (Elji), Nord (Nord), Polair (Polarr ), Pozis (posis), Sharp (Sharp), Shivaki (Shivaki), Siemens (Siemens), Snaige (Snaneig), Stinol (Stinol), Samsung (Samsung), Toshiba (Toshiba), Vestel (Westfrost), Vestfrost (WestFrost ), Whirlpool (Whirlpool), Zanussi (Zanussi), Elenberg (Elenberg), Biryuis, Yuryuzan, Atlanta, Oka Sviyag, Ocean, Minsk.

Step-by-step instruction

  • The temperature regime regulator must be put on the number “0” and turn off the unit from the power supply network, taking out the fork from the outlet. Leave the doors open;
  • It is necessary to extract all stored foods stored from the freezer, as well as the refrigeration compartment. It is not recommended to pull out products from the device with the boxes. From their severity, plastic may crack;
  • pull out all the boxes, grilles, partitions, shelves (they can be taken to the bathroom, since washing there it will be much more convenient than in the kitchen sink);
  • collect melt water;
  • wait until the technique is completely defrosted. The best traditional way to defrost the refrigerator is to leave it overnight until completely defrosting naturally. You can clean the thawing ice from the walls with silicone or soft plastic spatula;
  • Dry the space inside the device-tolerate the entire liquid and the remaining ice from the chambers with a dry soft rag or napkin. And also dry the floors under the technique and next to it;
  • Turn on the refrigerator in the outlet;
  • Fill it with boxes, partitions, shelves, grates. Set a temperature sensor to the desired value. Close the device;
  • wait 0.5-1.5 hours and put products in their places. If a red bulb caught fire, do not panic, we will tell you just below why.

Theory

The period of time through which the technique should be defrosting directly depends on the defront system (thawing) installed in it. The type of this system is indicated in the technical passport of the device.

Standard systems

The manual system of defrosting is installed in low.temperature cabinets and freezers. The entire defrosting process is performed manually. In such chambers, the process should occur with the increase in ice crust. When its thickness reaches 5 mm, then you should thaw the process.

No frost

No Frost, the most modern and perfect technology that protects the walls from intention. No Frost provides for thawing in automatic mode. Cold air flows through the aggregate chamber distribute a built.in fan.

Moisture condenses in a hidden evaporator in the form of hoarfrost. From heating the evaporator, the hoarfling thaws, and moisture merges into the pallet. From there, the liquid evaporates and as a result, ice does not remain on the walls of the chambers.

Drip defrust system

Mostly found in modern and inexpensive devices. such a system is called crying. In such devices, the period of freezing and thawing occur in turn. By turning on and disabled compressor. After a certain period of time. Ice accumulates on the evaporator located on the back wall. On the surface of which, after the compressor is turned off, condensation is formed. Water flows into the pallet by stocks and from there evaporates.

defrost, drip, refrigerator, liebherr, chamber, done

Life hacks and tips

First, it is necessary to give the refrigerator half an hour to stand before conducting all kinds of manipulations. Then, you can proceed to the experiments.

Fan

Install the fan by directing the air flow into the freezer. A similar option is a hairdryer. Just do it very carefully. It is necessary to ensure that the seal does not deteriorate from hot air (the elastic band may dry out), and the electric cable did not contact with meltwater water.

A few heated pots

Put a board in the freezer. On her a pan with boiling water or several. You can use a bucket or bowl. Change water as it cools. If you put a pan without a plank, you can damage plastic.

Special tools

In household stores you can purchase sprays for gentle removal of ice crust. Household chemicals are very effectively killed by harmful bacteria, and also eliminate the unpleasant odor. These funds are absolutely safe, since biodegradable.

For accelerated defrosting

  • Fill the heating pad with water and put it in the freezer;
  • spray with hot water spray the walls of the freezer (this is the safest of the offered options);
  • rub the ice with a rag soaked in hot water. The main thing is not to burn hands;

What should not be done

It is strictly forbidden to scrape off, chopping off holes and ice with a knife, wooden and metal blades. You can, thereby, break through the plastic and damage the thin trumpets along which the refrigerant moves. Freon leaks may occur and expensive repairs will be needed.

How often to repeat the procedure

There are no particularly clear instructions for the frequency frequency frequency. For different thawing systems, their approximate periods have been set. Manufacturers advise:

  • Technique with a manual defrosting manual system is most often defrosting at least once every six months. But, it’s better to do it more often.
  • Manufacturers recommend devices with a drip system of thawing twice a year. This process can be done much more often. As needed.
  • Owners of refrigerators with the No Frost system were lucky more. These units do not require special additional care. But, nevertheless, it is recommended to defrost them once a year for cleaning.

How to turn on

Before connecting the refrigerator to the power supply, you need to completely dry it. The surface of the unit is wiped as much as possible and leave the doors open so that it is completely dried

Care and cleaning of the device

All modern Liebherr refrigerators (Lebherr Premium, Liebherr Comfort, Liebherr Glass Line) are equipped. It is necessary to ensure automatic defrosting. Melt water evaporates due to the compressor, because the presence of drops on the back of the refrigerator is an acceptable condition indicating normal operation, confirming that the ice thaws. To avoid breakdowns, you need to regularly clean the hole for the drain from the blockage.

The freezer is also not necessary to defrost manually. Moisture condenses on the evaporator, is independent and evaporates.

Incorrect cleaning can cause damage to the device, so it is worth observing the following rules, ensuring equipment care:

  • You can use weak.concentrated cleaning tools for washing panels;
  • Do not use abrasive sponges (there is a risk of scratches and chips);
  • It is forbidden to use devices that provide hot steam cleaning;
  • It is important to prevent damage to the factory plate inside the unit, there is information necessary for service;
  • for washing it is better to use soft tissue and sparing detergent;
  • Inside the refrigerator, only means safe for humans are used;
  • It is important to avoid water entering the groove for drain, on electric nodes and in ventilation grilles.

Attention! Before washing from the refrigerator, you need to remove all the products, turn off the power plug.

| Denial of responsibility | Contacts |RSS