How to disassemble a manual blender vitess. Blender speed regulator

How to disassemble Philips blender video

For self.elimination of breakdowns, it is necessary to first disassemble the blender. This procedure has its own specifics. Following the recommendations of masters, without contacting specialized centers, prepared equipment for repair. This will save on paying for service or buying a new device.

At home, two types of blends are used: submersible (manual) and stationary. To carry out minor repairs, it is necessary to dismantle such a technique. The disassembly procedure depends on its design features.

In order to disassemble the device, regardless of its execution, you will need such tools and materials:

Additionally, a marker, instant glue, blade, soldering iron may be required.

Submersible

Submersible blender is a type of small household appliance, which is used for mixing, whipping, cutting, grinding, and breaking products. It consists of an elongated pen, under the casing of which a motor is located. A rotating lobed nozzle or corolla is attached to it.

To disassemble a regular submersible type adhere to this sequence of actions:

  • The screws are twisted. Their location is remembered or marked with a marker.
  • Dismantle all the details that are disconnected.
  • Inspecting unusual details. They can be attached using clamps or latches. They are disconnected by squeezing the lock lock.
  • Glue seams are destroyed with a knife or blade.
  • Subanated elements are dropped.

After disassembly, diagnostics and repair of worn parts is carried out.

Stationary

The stationary blender consists of a stable case, under the surface of which the engine is located. A bowl buried by the lid is put on the top of the device. Inside it is a lobed knife.

To disconnect the knife, they act as one of the methods:

  • A knife mounted on a spindle is wrapped in a towel so as not to get hurt, and then unscrewed. It should be borne in mind that fastening with left thread;
  • If the knife is planted on the nuts, they are twisted with a wrench and use pliers if necessary;
  • There may be a situation where a bowl is required to extract a knife.

If there is a suspicion that the reason for the problem is the wear of the engine, the gearbox, the control board, then the stationary device is disassembled in this way:

  • Disconnect the bowl from the body.
  • Turn the body with the base up and twist the screws of the mount.
  • Having put a small force, disconnect the device to the upper and lower parts. The base has a place for entering a network wire and a plastic casing, which houses an engine and board. These elements themselves are screwed to the upper part.
  • The screws are twisted with a screwdriver with which the engine, the diode bridge and the board are attached to the inner surface of the housing.
  • To pull the fee, it may be necessary to remove the handle of the speed regulator, bred on the outer surface of the case.
  • If the element is fixed by soldering, it must be dropped out.

The process of disassembling technology of this type is more complex compared to the dismantling of elements of submersible blender.

Features of disassembly of blends of different firms

Models of Brown, Polaris, Redmond, Philips, Scarlett, Bosch are widely used in everyday life. Some of them are disposable and non.combination. Their disassembly is not provided.

Brown technique is disassembled as follows:

  • Plafers remove the cartridge (nozzle holder).
  • A thin screwdriver is put in the seam between the body and the outer shell. Slightly hit with a hammer on a screwdriver, thus knocking out a welded seam. This action continues until the engine begins to move freely inside the case. Everything is done with great care, so as not to destroy the fixers. Do not use a thick screwdriver, it can damage the outer shell of the body.
  • Pressers press and extract the engine. Usually the control board is drawn together with the engine. If it did not succumb, she is pulled by pliers by the lower edge.
  • Inside there is a latch fastening cover. They are bent at the arrows.
  • A screwdriver shake the speed-lid.
  • The fixers of fastening of the network cord are bent, located inside.

Polaris’s models are collapsible and non-vegetable (for example, PHB-0713al), the details of which are glued or soldered.

Elements of collapsed blends are disconnected as follows:

The glued parts are cut, but to return the original appearance to such a blender when assembling.

In the redmond technique, all fasteners are fixators. They need to be disconnected carefully, otherwise, during assembly in the places of connections, non.execution.

Popular models of Randmond are disassembled as follows:

  • Remove the upper metal ring, bending the inner latches;
  • Having put a small force, remove the adjustment handle, holding a plastic axis of rotation and a spring;
  • unscrew 4 screws;
  • They push and remove the lower ring, gently tighten the metal protective casing;
  • They are treated with a knife around the circumference of the adhesive seam and remove the cylindrical part;
  • take out a guide sleeve;
  • put forward an engine from the housing along with the board.

Philips models are disassembled according to the following instructions:

  • From the side where the handle of speed regulation is located, they disconnect the decorative lid, picing it with a knife or screwdriver. it is attached with double.sided tape;
  • The next cover, fixed with screws, is dismantled with a screwdriver;
  • The plastic gear is removed with the hands;
  • The protective cover is uncovered on the back, for this, they are pressed on the buttons-liver buttons and the ear is bent with a knife;
  • This is followed by a glued shaped cover that protects the motor. it is disconnected with a knife.

At the final stage, the engine and control board are removed.

Skarlett models are disassembled in the following sequence:

  • They push the cap of the speed regulator with a screwdriver and remove it from the rod;
  • Unscrew 4 screws with which the lid is attached;
  • pull out a connecting sleeve closing the engine;
  • extract a motor and a fee.

The engine is the most vulnerable part of these devices.

Details of stationary BOSCH blends are dismantled using a wrench and pliers.

Dismantling of submersible varieties has features:

Types of blends

The thoughtful choice of a blender determines its effectiveness with further use in the kitchen. It is important to pay attention to the power of the device and what material the device is made. It also does not hurt to know how to fix the blender when it breaks down.

Submersible blender

A multifunctional portable device with the main purpose. grinding and knocking out products and liquids. Manual blender is quite simple in the device. Compact and convenient when using. An additional plus can be called the possibility of processing products in any convenient capacity. The main components of the device engine, control unit and spindle. Repair of a submersible blender does not require special knowledge and tools.

Stationary blender

The most complex and multifunctional technique is presented in the form of a stationary device. When cooking, it is used to solve a large number of problems. A significant plus is the free hands of the cook and the processing of a large volume of products in the blender. The structure of this device is more complex than that of a manual blender. It includes a glass or plastic bowl with a blade knife. In the case there is an engine with a drive shaft and a blocking mechanism.

Features of disassembly

There are two types of blends: manual (submersible) and stationary (desktop). To disassemble the desktop version, a wrench or screwdriver may be needed, depending on the type of fasteners of the lower cover cover. In this case, everything is simple: the screws or nuts are unscrewed, and the lid is removed, opening access to the internal device.

With submersible blends, the situation is more complicated, since their external fasteners are often fragile plastic latches, the location of which is unknown in advance, and the internal nodes can be additionally attached with screws, screws or bolts.

Dismantling of the manual blender “Bosch

It is necessary to start disassembling the blender of this brand by removing the layer of the rotation speed regulator of the mixer. It is located on the back of the device, and installed on two latches, as in the case of the brand of Brown Blender. Therefore, it is necessary to remove it in the same way as placing it on the position “2” or “3”, gradually promoting and pulling on itself.

Under the lid are two self.tapping screws with cross.shaped slots on hats. They must be twisted with a screwdriver. Now an important point on which the integrity of the design of the blender body depends. The latter consists of two parts interconnected in the method of slots along the body. These two parts must be disconnected from each other. This will require a screwdriver or knife. The tip of the tool is inserted into the gap between the parts of the blender and turns, thereby disconnecting them, from each other.

At the same time, a click will be heard, which says that parts are moving away from each other. This is not the sound of broken plastic, it is the sound of disconnecting latches. Separation is carried out on both sides along the body of the device. Structurally, BOSCH blender is a semi.divided. Its lower part is cast, therefore, when opening the body, take care so that there is no fracture of the cast. Now you need to get a plateau and a motor out of a blender.

Dismantling the Philips blender

Philips blends is a slightly different body design, which also belongs to the category of stiff. How to make it out:

  • From the back where the speed controller is located, remove the decorative cover. It is attached to the rear end of the device with bilateral tape. Therefore, it must be placed with a screwdriver or knife and disconnected.
  • Next is another cover fixed by two self.tapping screws. They can be removed with a screwdriver. Pay attention to the hats of fasteners, they have a special shape. But with the help of a conventional screwdriver you can unscrew them.
  • Under the lid is the plastic gear of the regulator. She is removed with her hands.
  • Now the disassembly process goes to the opposite side of the household appliance. There is a lid, which is intended to protect the internal mechanism of the blender from garbage, dirt and water. It is fixed on the device with two buttons-skeletons. They need to be pressed with a screwdriver, and bend down with a knife. After which the cover is easily removed.
  • Under it is another cover, which is attached to the blender body with an adhesive composition. It is shaped and closes the shaft of the electric motor and the engine itself. With a knife, you need to remove the glue and pull out the lid.
  • Now the electric motor itself is pulled out with the control board, which must be checked for performance using the multimeter.

Bleader of the Polaris and Redmond model is understanding the same. The only difference is four self.tapping screws from the back from the cross.shaped hats that hold the plateau inside the device, the first and three of the second.

Electric circuit and motor

After disassembling the blender, the motor and electric circuit are extracted. They are checked visually. If there is no obvious damage: the smell of burning wiring, carbonization of radio components, jamming of the shaft, poorly soldering, you should proceed to the call.

disassemble, manual, blender, speed

First of all, the fuse is checked, if any, and the extinguishing resistor is provided. Then the diodes (. The cause of the malfunction may be the rectifier capacitor. When detecting faulty parts, they are replaced with original or analogues. The main thing is that they coincide in power. Semi.Istor, which is a regulatory element, is difficult to check, but these details rarely fail.

The rotation speed adjustment can be carried out smoothly, using a resistor or discrete. switch. In both cases, they also need to call.

Having made sure of the operation of the electrical circuit, they start checking the motor. The collector scheme allows you to easily determine the malfunction. The smell of burning and the lack of contact between the windings (access to which is carried out by disassembly of the motor and release the collector) will indicate partition. In this case, further repair is inappropriate financially.

Sometimes the lack of contact on the windings is justified by the failure of the brushes. They are easily extracted and changed.

The restored motor group should easily turn manually. Before assembly, all rotating parts must be cleaned and greased.

Blender assembly is done in the reverse order. If you manage to master the repair yourself, you will not be worth it to make a submersible blender with your own hands.

Breakdown associated with electricity

If a spare part participating in an electric circuit has come out of the system, a complete disassembly of the device is needed. The reasons can be varied. The most common problems that arise with the speed regulator and the complete stop of the device. Blender engine repair is better to entrust professionals.

Speed ​​regulator problem

Problems that arose with speed regulation require a professional approach. To correct such a malfunction at home, you need to have certain knowledge in the field of physics and have a specialized tool. For lack of the latter, it is recommended to take the blender to the service center. Vitek blender repairs are carried out in the same order.

KENT Hand Blender 150W 5 Speed Control Review / Hand Blender 150W /#shorts /#kitchengadgets

With independent work, the following steps should be followed:

  • Disassemble the blender body.
  • Free access to the switch, removing the details that interfere with the repair.
  • Drop the speed regulator.
  • Check the regulator in all possible positions.

Important! If the rotator of the instrument revolutions works correctly, then the contacts of all speeds are strengthened in accordance with the requirements.

If the blender stopped

A full stop of the device can provoke a fairly large list of reasons. For each of them there is a way to eliminate the malfunction. The extracted motor and electrical circuit are subject to careful inspection for visible damage. Next, you should call the key contacts of the device. First of all, check the fuse, resistor, diodes. After the rectifier capacitor and the simistor. If the electric circuit is in working condition, the next step is examined by the motor.

There is a buzzing when turned on, but the action does not occur. possible breakdowns

There are situations when the device ceases to function, but at the same time makes characteristic buzzing sounds. The reason for this phenomenon is usually jamming of the cutting parts. To eliminate the breakdown, you need to separate the bowl and carefully squeeze the button of the turning on the inclusion. To do this, you can use flat pointed items. If the work of the blender has recovered, then the reason was established correctly. Blender’s repair of Vitek is carried out according to the same principle.

In the case when the blocking button did not help, most likely the motor winding was combined. A clear sign of a burned engine is the presence of a characteristic smell of burning wiring and the appearance of sparks. With this development of events, it is recommended to seek specialized help.

No buzzing when turning on

The reason for this phenomenon may be various factors.

  • Disconnecting electricity in the building.
  • The outlet failed.
  • Deformation and fracture of the electrical wire of the device.
  • Farting an internal fuse.
  • Violation of the integrity of the motor windings.
  • Visible damage to the electrical board (interruption of paths, deformation).

DIY repair solves many problems. If it is not possible to find out the reason for the malfunction or purchase the necessary part, then the device should be submitted for repairs in service services.

Step-by-step instruction

The blender device is quite simple, does not require deep knowledge in technology. Imagine how to disassemble Philips blender using several models as an example.

HR-1363

To disassemble the Philips 600 WATT blender, disassemble the nozzle. Often manufacturers glue plastic parts using heat treatment and their subsequent nozzle on each other. Therefore, to disconnect the details, you will need a thermal pistol.

Having removed all the upper details, you will find a plastic gear inside, which often breaks. It can be replaced or tried to restore it.

It will not be difficult to disassemble the Philips 600 WATT blender, however, if you analyze the device for the first time, they recommend taking pictures of each stage of analysis so that there are no problems with the assembly.

HR-1372

To disassemble the Philips 700 WATT blender, remove the external (upper) and lower couplings with screwdriver, remove the gearbox from the cover. Some details can be soldered with each other, so you may need an additional tool for analysis.

Devices 600-700 watts are not too powerful, so it takes more time to work, respectively, more load goes to the engine, mostly it fails of such models.

HR7768

Consider the Philips HR 7768 combine how to disassemble the model and identify the cause of the malfunction to obtain access to the internal details, you need to remove the upper cover of the motor compartment (self.tapping screws under the plugs), remove the operating mode switch. Next, unscrew the bolts on the upper and lower lids of the compartment, carefully disconnect the details from each other. Most often, the problem arises in the engine.

Reference. If you purchase original new details for replacement, then the equipment will last much more after the repair.

Repair Philips blender

When damage, it is necessary to determine exactly which part failed. A common cause of malfunction of the PHILIPS submersible blender is the cord. The device is often tolerated, turned on and off. Constant excesses of the cord lead to its failure. With an unstable electric network, engines break.

From less significant breakdowns, you can distinguish the leakage of the bowl, failure of the speed regulator, nozzle, knife. Not every detail can be repaired, sometimes a replacement for a new.

Consider the main details subject to breakdown.

Repair of the PHILIPS blender gearbox

It is difficult to repair with your own hands, you may need complex additional equipment. If the broken wires of the engine from the board are visible during the analysis, then it is enough to solder them back to the right place.

If there are no visible cliffs, you need to check the current supply brushes. If they look worn out, they need to be replaced with new. The brush is disassembled quite simply, but, at the same time, remember that you need to bend the petals only in extreme cases, they are quite thin, they can break off.

If the problem is more global, for example, a bearing has failed, or you need to rewind the stator winding, at home such manipulations are quite difficult to perform. In this case, the device can be attributed to the workshop or buy a new. They will tell you how to fix the blender quickly and without additional costs.

Repair of the bowl of the device

A large number of models, such as HR1670, HR1679, and others. The set contains bowls and glasses. If microcracks appear and the bowl proceeds, then it can be strengthened using hoops from the outside of the bowl. But this will not give a long result. When leaking the bowl of plastic, it can be sealed with a soldering iron or thermal pistol.

In case of malfunction, the latches will need to be changed completely spring-fixing coupling.

Dismantling and repair of the bowl itself will take a lot of time, sometimes it is better to replace it with a new one, or use improvised capacitors for work.

Repair of the Blender nozzle

The main thing is the nozzle for grinding and cutting products, it is it that it experiences maximum loads often fails the first. PHILIPS blender knives are made of high.carbon steel with special hardening. If the knife is swept away, it is better to turn to the master, and not to sharpen his at home, sharpening occurs according to certain rules.

You can disassemble Philips blender, pull out the components and bring only one or more broken details to the workshop. This will accelerate the sharpening process and save you money.

KOIOS 800-Watt/ 12-Speed Immersion Hand Blender(Titanium Reinforced), Turbo for Finer Results

If the problem is in the shaft itself, which is loosened from vibration, the backlash appears, and accordingly, the shaft fails. It is quite difficult to solve such a problem on your own, it is better to warn it, periodically tighten the nut of knives fastening.

The repair of the Philips blender with minor malfunctions can be carried out less often if the blender, like another device, are used strictly for its intended purpose. Each model has detailed operating instructions, which contains maximum loads and technical breaks in work.

Important! If the device has broken, but the warranty period has not yet come out, do not open the body. Take it to the service point, most likely, will reveal a marriage and replace the parts or completely device for free.

Step-by-step instruction

Consider the disassembly on the example of a fairly common model of the PHILIPS HR 1372 submersible blender, which is protected by the manufacturer from disassembly and repair at home (common causes of breakdown are described in the article: why the blender may not work). PHILIPS submersible bleeders of this type are disassembled from the fastening side of the nozzle. In this part of the case there are two plastic latches, hardly linked to the round “ears” of the removed part.

It is impossible to push them with fingers, so we use for this two small screwdrivers and a penny knife with a thin blade. One screwdriver needs to raise the edge of the latch, and the other a little shift the “ear” towards the exit from the engagement. We will do the same on the other side, after which it will be possible to easily remove the anterior black plug from the side of fastening the nozzle.

Under it, we will see another plastic plug of white color, which is already attached not on latches, but on the jet! To get it, we will have to use the penknife, or better with a clerical knife with a very thin blade, which needs to cut the glue, walking with a blade along the edges of the plug adjacent to the body.

After removing this plug, we will see an electric motor with a spindle. But we will not be able to get it right away, since something else holds him back. In the rear end of the PHILIPS submarine, a metal decorative lid is located, which lasts only on double.sided tape. It can be easily lifted with a small screwdriver and remove. Under the lid we will see two non.standard screws at the power supply that hold the electric motor and do not allow it to be removed from the other side.

These screws have unusual hats with two excavations at the edges for a special key. Neither the usual nor the crusade do not fit them, but with some dexterity they can still be unscrewed with ordinary screwdriver or scissors if they are not very tightly twisted. By unscrewing the rear screws, we will be able to easily get an electric motor along with the control circuit from the body of our submersible Philips blender and see what this design is.

PHILIPS HR 1372 device

The inside of the blender is: an electric motor and control circuit with buttons, which is fixed on a rounded plastic frame. In order to conduct their diagnosis and repair, you need to disconnect all the wires and free the electrical circuit from the plastic frame. After that, you can check with the help of a tester the serviceability of the electric motor and the elements of the electrical control circuit.

Faulty electrical elements in the diagram can almost always be replaced with similar characteristics, and the very scheme itself is cleaned from pollution, which can also cause a malfunction or interruption in the work of a submersible blender.

In the event of a burning of an electric motor, it can only be sent to a landfill, since it is almost impossible to fix it at home. The electric motor can also be replaced, but only entirely and on exactly the same size and electrical characteristics.

If, on the contrary, the motor is working, and the management scheme could not be fixed, then it can be left for “spare parts” to use somewhere else.

What you need to know about the device

In a store with equipment you can see many varieties of a blender, with various nozzles and functionality. However, all of them can be divided into 2 types. submersible and desktop.

Submersible bleeders are a base with a motor and several nozzles, there is no bowl. Work can be done in any convenient capacity. These models are more compact and cheaper.

A desktop or stationary blender is a base with a bowl and a set of different nozzles. Such models have great power, and the volume of the bowl allows you to load many products at the same time.

Nozzles are easily removed and dressed on the base. Popular nozzles at the blender are a whisk, a niner knife, a puree former.

The blender is a technically simple device, but it is better to choose a technique from proven brands. The mechanical breakdown or wear of the part can occur with any manufacturer, and it is not always possible to take it to the master or hand over it under warranty. Let’s deal with the main breakdowns of an electric blender and how they can independently eliminate these breakdowns.

Step.by.step instructions how to disassemble a blender

Before disassembling a blender, first study the operating instructions so as not to finally break it. To analyze the tools, you will need a screwdriver, a magnet for small parts, pliers and glue to fix the seams during assembly. Repair must be done, after turning off the blender from electricity.

  • Unscrew all the screws with a screwdriver and remove all the elements that are not fixed.
  • Sometimes the internal parts are fixed on the latches. we carefully remove them.
  • After all possible details have taken out, we examine the integrity of the entire device.

If during operation some plastic parts have cracked and interfere with the correct work, then they need to be replaced. The same thing, if the details are not in its place, then fix them and assemble the device.

If after such an inspection the device has not earned, then the reason may lie in another.

Hand bleeders

Collective engines are often used in manual blends, motors can operate, powered by constant and alternating currents. In simple models, buttons of power are available, directly contacts of brushes. Capacitors are attached to sparking near the rotor. Let’s say more, in addition to capacitors, varistors, shackles of voltage surges, protecting the windings against combustion. In the simplest models, thermo.guards are placed among the turns. If it burns out, components should be replaced with new. The scheme is used in collector and asynchronous types, transformers. Do.it.yourself repairs with your own hands require the knowledge of unwritten basics of electrical engineering, electronics. Here are the basics. knowledge. today we will do.

Internal device of manual blenders

Collector engines are supplied with stabilization schemes, but the simplest blends of the delights are deprived of. Varistors make up an important node of many devices, protect not only motors. In the pulsed power sources, the shutdown of high frequency generators with a closing of current to fuses caused by overload. The result is the operation of the defense. Reveal a malfunction by replacing the fuse with a light bulb: it is on. the food is turned off, continuing to search for problems.

The simplest collector engine is formed by a pair of stator windings, a good bunch of rotary. Under the brushes there is a drum broken by sections. Each pair of opposite contacts is equipped with a closing coil. Assigning the serviceability of the blender, call each, rotating the shaft with your hand. Often the bearings are considered a weak place. Two nodes. front and rear. The lion’s share of the load falls on the last. Hado is used for lubrication. After use, the composition causes the formation of a ceramic film, which temporarily improves sliding, protecting the surface.

If the friction is too large, burning the current.consuming parts, blackening of the body, parts, peeling of the soldering are possible. Blage the rotor to extract from the bearings, wipe with alcohol, grease the details. The collector engine is always noisy, inertia is considered dignity to help to avoid rulings of revolutions. When switching the rotor windings, a reverse EMF occurs. This is a parasitic effect, this phenomenon was learned to use for the good. The regulatory circuits of thyristors are assembled: the input voltage with the reverse is folded on the control electrode. The load of the shaft increases, the speed falls; The reverse EMF is reduced, the thyristor opens, the current consumption increases, the engine speed reaches the norm.

In manual blenders, such solutions are used with reluctance, the switching element is very hot, the enormous radiator simply has nowhere to place. However, when using simple speed adjustment, greatly facilitate the life of the hostess.

disassemble, manual, blender, speed
  • Sudden changes in voltage consumption require filtration (jumps) on the power circuit, cause steep changes in the external network. The effect is noted when working from the generator.
  • Speed ​​regulation is valuable quality, but if the power increases sharply when the dough is kneaded, the blender will vomit from the hands of the hostess, there is little good. It is more useful for calm women to buy home a blender that issues constant power, regardless of the prepaid dish.

In advanced models, the blender device is supplemented by speeds. often we see separate buttons that are clinging continuously, forcing the engine to work. Made for a reason. The developers realize: a weak female hand is quickly getting tired, therefore, the key will probably be released before the engine combustion. The adjustment technique is more often not characterized by unprecedented complexity. The output voltage is removed by paired secondary windings of the transformer. There is a change in revolutions.

Blenders often burn if varicaps are protected against voltage jumps, thermal guide guard the equipment against overheating. In the power chain, put an element with a gun threshold 120 degrees. At times, the thermal object is placed between the boots of the motor (mentioned above). The pulse power supply operates according to an ordinary scheme. At the entrance, the voltage is filtered by capacitors, throssels, resistors, a signal passes a high.frequency power transistor (even two). The process is controlled by a microcircuit generator that supplies the voltage to the controller shutter. At the output, the voltage is filtered if necessary, less often straightened.

Frequent breakdown. burnout of the winding. Try to buy products equipped with fuses. Simplify your own life incredibly.

Collector engines are controlled according to the voltage cutting circuit when a smooth transition is required. In the case of two or three fixed speeds, there is probably no need for such a scheme. The sinusoid, according to a positive and negative half.wave, is covered on a certain site. The acting value is reduced, naturally causing a decrease in the speed of the shaft of the collector engine. As already mentioned, kitchen appliances are equipped more often with trivial regulation. It is unlikely that the repair of Blender Vitek will require deep knowledge of circuitry.

We add that reusable thermal objects are noticed, after the reinstalling circuit, after a given period of time, is triggered. Others are designed for 100 work cycles. Decide for yourself whether the functioning resource is enough regarding your own view of the device. We list that it can break (power supply):

  • filters;
  • diode bridge;
  • transformer;
  • generator;
  • key transistor;
  • rectifier output diodes;
  • varicaps;
  • circuit breakers.

Do.it.yourself repairs will require knowledge of the basics of electronics. Nothing complicated, at the request in the Комментарии и мнения владельцев we will create a topic that paints the theme of power sources. Everyone who is in the stream will repair the blender on their own without problems.

Features of desktop blends

Manual devices are deprived of an important ability. to prepare cocktails like people. Need a desktop blender equipped with a capacious bowl. Cross sharp knives are located at the bottom, the junction of the joint is a true disaster. The rod of the motor is crowned with a relatively soft lower half of the drive clutch. A ring formed by dense rubber, the perimeter, forming a crown, the teeth are located. Each is included in the corresponding deepening of the upper coupling. The lower half is devoid of hard thread. Remove the part with a screwdriver and a hammer, hitting the teeth, setting rotation clockwise, the masters recommend that the clutch carefully, pulling it up. Then a new part is wound counterclockwise. Thread, of course, left.

The coupling is a responsible part that protects the engine of the aggregate against overload. When jaming knives, clicks will be heard. Love to turn off the blender. after waiting for a while, the lower half of the coupling will become incompetent. With the upper half problem: seals sometimes proceed. Seeing an unfavorable alignment, get ready to disassemble the device. When driving your hands, unscrew the assembly of the knives from the bottom of the bowl. Rubber gasket is laid aside.

The upper half of the blender coupling is wound on a rod, seated with knives, left thread. The direction of rotation of the knives will be recognized by the anterior acute kamke. Capture with a large divorce key through a towel (fabric) of the blade in the location of the rod, twist in the direction of reverse rotation. Under the upper half of the coupling, a pair of sealing rubber washers, one steel. Both varieties are removed, knives can be removed from the assembly. If necessary, the blades of the blender are dragged. Pay attention: from the inside of the bowl is an additional double rubber seal. Replace the details with purchased or those that you managed to get.

Bleader’s reverse assembly is made in a similar way. Remember: Left coupling carvings. Tighten the nut, avoiding knives. Caution, beware of the cuts of the Blender blade. The engine at the base under the bowl is not much different if you compare with manual models, but it can better withstand the load. Often speeds 2-20, the simplest processing programs for processing food processing are laid.

Blenders often sell an integral part of the kitchen combines. Through the gearbox, the shaft of the knife is rotated. Protection against the inclusion of a mechanical, leading shaft (cutting, shinkling) is located separately, at the same time with the side does not spin. The speed of rotation of the blender, of course, above, is necessary to increase the gearbox.

The presentation is over today. The presented models of good are similar to each other. Planning to repair the Tefal blender, the master master repairs of Scarlett blender. Further more, the manufactured household appliances are similar to each other. Perhaps readers have not heard, but 85% of washing machines, like blends, are equipped with collector engines. Therefore, the repair goes according to the same scheme. In our case, the speed adjustment is provided by the design. The advantages of collector engines in terms of adjustment over asynchronous are obvious. In the latter case, the stator winding is often divided by a fixed number of sections. This method easily reproduces three speeds, the alignment is not suitable for advanced solutions. The washing machine only on the spin has 3-5 speeds. The scheme that contains the power key with the cutting mode of the current simply begs.

This is why the repair of blends is similar. Experts of coffee grinders, drills, screwdrivers, mixers and even vacuum cleaners will perform the necessary sequence of actions without noticing the change in the kind of technique.

So they make independent repairs of the blender. We recommend fixing the device according to warranty, an expensive model to disassemble only if necessary. Indicative border of cheapness Count the amount of 3000.

| Denial of responsibility | Contacts |RSS