How to remove the laid of the washing machine Hotpone Ariston. Damage to the handle

Disassemble the washing machine Automat Ariston

In the repair of the Ariston Washing machine vertical loading AVTL83 model. Among the widest Ariston machine operating series, this model is widely used thanks to several obvious advantages.

Firstly, it can be conveniently placed in a small and narrow bathroom, especially for Khrushchev’s houses.

Secondly, the upper load of linen allows you to stop the car at any time and report things if there is such a need.

In our case, the client filed the following complaint: Ariston washing machine does not warm the water and does not break through the linen poorly. We suspect that the heating element (heating element) has failed, which means that the heater is tested with a multimeter and, if necessary, replacing it.

The basic rule that must be adhere to during any repair is de.energized before starting work. This is an important safety requirement, so we turn off the car from the electric network.

Dismantling of Ariston washing machine vertical download.

Replacing the heater with a vertical loading machine has its own characteristics, because the design of the vertical load differs from the front machine. First of all, you need to remove the left (if you look at the back) side wall of the car. To do this, we unscrew the screws of the side wall mounts located from the back on the left side, as in the photo below.

Then we remove the plastic panel that closes the drain pump filter and located in front of the machine below.

There are two screws and they need to be twisted, they also fix the side wall.

Now with a light movement of the hand we move the side wall back and a little down, remove it to the side.

I would like to note that when we removed the side wall, a very good access to the internal nodes of the machine was opened. Therefore, the Ariston washing machine vertical loading is very convenient in repair. And this applies not only to the replacement of Ten on Ariston, but also to other types of repair.

Instructions for removing the upper cover from the Ariston washing machine

Starting the stage of disconnecting the upper cover, you need to consider how the laundry is loaded into the washing machine. This refers to frontal (horizontal) or vertical loading. Accordingly, such modifications differ in the methods of fastening. This is due to the design of washing machines, including Ariston. As well as the inability to fix the upper cover in models with vertical loading similarly to models with horizontal.

Step.by.step instructions for removing the upper cover of Ariston machines with front loading

First, consider how to remove the upper cover of Ariston with a horizontal load:

  • from the back, in its upper part, all available self.tapping screws are removed. Their number may vary, depending on the specific model of Ariston machines, usually two of them. It is very important not to lose them in the process of work. Therefore, pre.prepare a place for their conservation until the cover is installed back;
  • It is necessary that the mounts come out of the grooves, so the upper cover is slightly shifted towards the rear wall and lifts upwards upwards.

So, the lid is removed, and you can proceed to further repair.

remove, laid, washing, machine

Step.by.step instructions for disconnecting the upper cover of Ariston machines with vertical loading

If we are dealing with cars that have a vertical load, you need to take a few steps that differ from the previous instructions:

  • In order to get to the lid mounts, which in this case leans back to extract from the drum of linen, you need to remove the control panel. Two self.tapping screws that are located on the back wall of the machine are turned off with a cross.shaped screwdriver.
  • After that, already with a flat screwdriver, the panel is neatly lifted from special grooves and removed to the side. This must be done very carefully, trying not to damage hanging wires;
  • After the panel is removed, it is necessary to unscrew the four screws on the body of the washing machine, with which the upper cover is attached to the body. They are located on the opposite side of the side. They need to be removed, not forgetting to put in a reliable place so as not to lose;
  • At the end, carefully remove the lid, without damaging the latches with which it is inserted into the machine case.

Dismantling of the case

The degree of disassembly of the Ariston machine depends on the nature of its breakdown. Often, complete disassembly is not required and only partial can be dispensed with. to inspect the main nodes. Dismantling of the washing machine begins with the removal of the service hatch located on its rear wall. This allows you to immediately access the electric meter with a drive belt, temperature sensor, het and pulp of the drum. If further disassembly is required, then remove the upper cover, which is attached with two screws on the back wall of the washing machine. Under it you will find a big counterweight, tank springs, control panel and interference filter. The counterweight prevents us from getting to the tank with a drum and some sensors located below. Therefore, if necessary, it will have to be removed using a special key.

To remove the front control panel, you need to get a tray for powder and unscrew the screws under it, as well as two screws on the left and right, located under the upper cover. Now, if you pull the control panel up, it will withdraw without difficulty.

Then we turn the machine on the left side and look at what below. If your washing model has a bottom, then we remove it. But usually it is not. From below we can access the drain pipe, engine, pump, filter and shock absorbers.

The location of the parts in the lower part of the washing machine

This is where the partial disassembly of the washing machine case is completed, and now we can remove some nodes and details from it.

How to make out the washing machine Hotpoint-Ariston?

Like any complex technical device, Ariston trademark washing machines also have the properties of breaking. Certain varieties of malfunctions can be eliminated exclusively with the help of almost complete disassembly of the unit on its components. Since the main part of such malfunctions of the HotPoint-Ariston washing machine can be fully corrected on its own, an independent disassembly procedure should not be confused. How to implement this, we will consider in this publication.

Training

First of all, it is necessary to disconnect the washing machine from all communications:

It is advisable to drain the remaining water from the tank in advance by means of the drain filter or a tube near it. Next, you should prepare free space for the location of the very washing unit and units removed from it and components.

We prepare the required tools. To disassemble the Ariston washing machine, we will need:

  • screwdrivers (cross, flat, hexagonal) or electric screwdriver with a set of bits of various types;
  • Otrous keys to 8 mm and 10 mm;
  • a basket with heads on 7, 8, 12, 14 mm;
  • Passatigi;
  • Kusachki;
  • a hammer and a block of wood;
  • There will be no excess pulp for bearings (when the wrestling of the washing machine is carried out for the sake of replacing them);
  • hacksaw with a canvas for metal.

Step-by-step instruction

Having completed preparatory work, we proceed to the measures for disassembling the HotPoint-Ariston washing machine.

Upper laid

Without dismantling the top, there is no way to remove other walls of the unit. Therefore, turn out the mounting screw from the back side of the screw, shift the lid back and remove from the place.

There is a large block of equalization of the position of the washing machine (counterweight, balancer), which closes access to the tank, drum and certain sensors, nevertheless, it is quite possible to get to the intercoting filter and control panel. Turn his bolts and remove the balancer to the side.

Back and front panels

From the side of the posterior wall, by means of a cross screwdriver, we unscrew several screws holding the back wall. Having removed the rear panel, many nodes and details become available to us: a drum pulley, a drive belt, an engine, a thermoelectric heater (Ten) and a temperature sensor.

Carefully lay the washing machine on the left side. If your modification has a bottom, then we remove it, if the bottom is absent, then this facilitates the task. Through the bottom, we can get to the drain pipe, filter, pump, electric motor and dampers.

Now we dismantle the front panel. We unscrew 2 screws located under the upper cover of the machine body in the front right and front left corners. We turn the screws located under the tray of the washing unit, and after that we take the control panel and drag up. the panel will be freely removed.

Moving elements

A pulley with a belt is fixed to the back of the tank. Carefully remove the belt primarily from the pulley of the electric motor, and then from a large pulley.

Stages of work

On the one hand, the disassembly of Ariston washing machine is quite simple, since the front panel does not need to be removed here. On the other hand, the manufacturer provided details and fasteners, which are difficult to remove to a beginner master.

We will figure out all issues in order.

Remove the panels and lids

First of all, the upper panel is removed, which is attached with two screws.

To remove the top cover of Ariston washing machine, they need to be unscrewed from the rear wall of the cross or hexagonal screwdriver. Then push the lid in the opposite side of you, raise up and set aside.

Start the back panel. To remove it, unscrew the bolts around the perimeter, remove the panel to the side. You gained access to the engine and pulley of the drum.

It remains to remove the control panel. Squeezed of work:

  • Pull the submarine tray for detergents. Clutching the latch in the center, pull the tray over yourself and take it out of the body.
  • Unscrew the screws that are behind the tray and from the opposite side of the panel.
  • Using a flat screwdriver, squeeze the plastic latches. Take a picture of the location of the wires on the panel or mark them with a marker.

You will also need to remove the clamp from the hatch cuff so that it is possible to get a tank. Having pushed the seal, pry the clamp with a screwdriver and remove. Turn the cuff inside the tank.

So, with the panels we finished. We move on.

We dismantle the details in the back

Return to the back wall cm. You need to remove the drive belt by removing it from the pulley. To do this, pulling it over, scroll through the pulley.

  • Pay attention to the HotPoint Ariston washing machine. It is located at the bottom, under the tank.
  • To pull out the electric motor from the case, disconnect the wiring leading to it.
  • Unscrew the bolts that hold the motor. In cars of this brand, the part usually holds four bolts.

It is not necessary to remove the heater from the planting nest. In this case, the sealing rubber of the element is not subject to restoration. Therefore, it is enough to disconnect the terminals and wires leading to the heater.

Time to remove the drain pump. If the engine could be reached through the rear hole, then the pump cannot be removed so. Will have to turn the washer to the left side.

note! If you are uncomfortable to remove the motor through the service hatch behind, you can also do this through the bottom.

  • Unscrew the screws of the lower cover mounting if it is in your model.
  • Remove the screws that are in the area of ​​the drain filter on the front panel.
  • Push the filter, it must fall out with the pump.
  • Pour the plots of the metal clamp on the drain pipe.
  • Disconnect the pipe from the pump.
  • Unscrew the bolts fastening the filter and pump.

Excellent! Now the pump is in your hands. We proceed to further disassemble the Ariston washing machine.

Remove the parts at the top

Go to the upper hole of the cube.ariston, inspect all the elements of the machine. What else prevents the tank from pulling out? That’s right, interference filter and press.

Also disconnect the Pressostat hose from the tank body, otherwise it can break off when dismantling. Often manufacturers attach wiring on the tank using plastic clamps. Have a snack them with bites and push the wiring to the side.

Stages of work

On the one hand, the disassembly of Ariston washing machine is quite simple, since the front panel does not need to be removed here. On the other hand, the manufacturer provided details and fasteners, which are difficult to remove to a beginner master.

We will figure out all issues in order.

Remove the panels and lids

First of all, the upper panel is removed, which is attached with two screws.

To remove the top cover of Ariston washing machine, they need to be unscrewed from the rear wall of the cross or hexagonal screwdriver. Then push the lid in the opposite side of you, raise up and set aside.

Start the back panel. To remove it, unscrew the bolts around the perimeter, remove the panel to the side. You gained access to the engine and pulley of the drum.

It remains to remove the control panel. Squeezed of work:

You will also need to remove the clamp from the hatch cuff so that it is possible to get a tank. Having pushed the seal, pry the clamp with a screwdriver and remove. Turn the cuff inside the tank.

So, with the panels we finished. We move on.

We dismantle the details in the back

Return to the back wall cm. You need to remove the drive belt by removing it from the pulley. To do this, pulling it over, scroll through the pulley.

It is not necessary to remove the heater from the planting nest. In this case, the sealing rubber of the element is not subject to restoration. Therefore, it is enough to disconnect the terminals and wires leading to the heater.

Time to remove the drain pump. If the engine could be reached through the rear hole, then the pump cannot be removed so. Will have to turn the washer to the left side.

note! If you are uncomfortable to remove the motor through the service hatch behind, you can also do this through the bottom.

Excellent! Now the pump is in your hands. We proceed to further disassemble the Ariston washing machine.

Remove the parts at the top

Go to the upper hole of the cube.ariston, inspect all the elements of the machine. What else prevents the tank from pulling out? That’s right, interference filter and press.

Also disconnect the Pressostat hose from the tank body, otherwise it can break off when dismantling. Often manufacturers attach wiring on the tank using plastic clamps. Have a snack them with bites and push the wiring to the side.

Difficulties in disassembly

Before completely disassemble the Ariston washing machine, you need to remove the counterweights. In other brands of cars, there are no difficulties with their removal. But Ariston manufacturers equipped the counterweights with special mounts. To remove them, you will need a special key, as shown on

If you managed to remove the counterweight, excellent! Proceed to unscrewing the racks. Racks on plastic rods are attached. You can pull them out only by pressing the latches that hold them in place. For this:

Now the tank is kept only on hooks-pendants. To pull the drum from the Ariston washing machine, lift it up, removing it from hooks.

Another difficulty. If you need to get the drum from the tank, it will have to be sawed, because in these models it is unlimited.

Before the cut, you need to take care of the further assembly of the tank. To do this, make holes around the perimeter, into which then screw the bolts. Also prepare glue or sealant.

If necessary, you can replace the bearings.

To collect parts of the tank back, install the drum in place. Cover the edges of the halves with glue or sealant. Which tool is better to choose for sealing, we wrote in one of the articles.

It remains to fasten two parts and tighten the screws. The assembly of the machine is carried out in the reverse order.

Those who are just going to analyze the Ariston washing machine, we suggest watching the video:

Checking the heater by a multimeter.

Here is the Ten Ariston (heating element).

We remove the power terminals and check the heater by a multimeter (tester). We measure the resistance on the Omas, the working resistance should be approximately 30 Ohms.

The tester does not show any resistance, which means the heating element is “in the cliff”, that is, it is faulty. It is necessary to replace Ten Ariston. With this defect, the machine will fully work out the mode, but washing will pass with cold water. That is why things will be poorly washed off.

remove, laid, washing, machine

In the particular case, it also happens that the heater “does not break off”, but begins to close to the case. In this case, Ariston washing machine will not fully work out the washing mode. She will stop and give out error F08 (error codes can be viewed here) before rinsing. When checking the heater by a multimeter, the resistance at the ends will also be normal (approximately 25-30 Ohms), but when measuring the resistance between the ends and the body (mass) on the mega, the tester will show the resistance from 1 MOM to 200 MOM. In this case, it will also be necessary to replace the heater.

How to disassemble the battery of Atlanta Washing machine

To carry out a more complex repair, for example, the installation of new bearings, it is necessary to extract from the housing and disassemble the tank, and then pull the drum out of it.

This process is as follows:

  • Unscrew and remove counterweights.
  • Remove the drive belt.
  • Disconnect the wiring from the motor, unscrew the fasteners, remove the motor.
  • Disconnect the wiring from the heating element and temperature sensor.
  • Remove the clamps of the pipe of the bay and drain.
  • Pull the manner of the hatch from the drum.
  • Disconnect the press.
  • Pull the racks, remove the tank from the body.

Unlike a number of other manufacturers, it is impossible to disassemble the tanks of the Atlanta washing machines, so to install a new bearing, they need to be sawed. Necessary:

  • Put the tank with a hole for linen up.
  • Find a place in which two halves are soldered.
  • Pick up screws for subsequent twisting the halves of the tank.
  • Drill holes that correspond to the diameter of the screws. It is recommended to do this immediately so that when assembling it is easy to combine parts.
  • Cut the tank on the seam with a hacksaw. This is a laborious process that should be done carefully so as not to hurt the drum and other elements inside.
  • Divide the sawed tank into two halves, the top remove the upper to the side.
  • Wipe the screw located in the center of the pulley. If he seized, apply WD-40 to him.
  • Remove the pulley.
  • Choose a screw similar to the pulled out of the pulley and screw it into the shaft to knock it out to knock it out.
  • With light blows on the screw to knock out the shaft with the drum and bearings.

Dismantling Scheme of Washing Mashina

Devices of any manufacturers like Ariston, Indesitis or other machines have a similar structure and the principle of disassembly. Only small differences in the details can be present, which we will talk about later.

The main schemes are predetermined mainly by the type of loading of linen.

Horizontal load

First you should de.energize your device, remove the drain hose from it and turn off the water supply into it.

If you know the internal structure of all the elements of your washing machine, then you can guess about which part of the machine there was a breakdown and without wasting time to disassemble the entire washing machine to start doing this from the place of proposed breakdown.

  • Reducing the quality of washing, increased noise during spin and poorly squeezed underwear indicates the presence of a problem in the pump, or is it just clogging of the hose. To eliminate a breakdown of this type, disassemble the machine from below, or just remove the front panel.
  • If you notice that the water does not heat up, then this is most likely a breakdown of Ten. You can find out the location of this part by reading the instruction. As a rule, you need to remove the rear panel, but in some models of washing devices this part may be in front.
  • If the drain occurs longer than usual, then the problem is in the press or pomp. Based on the constructive structure of the washing machine, the part can be located either behind the side panel, or in the upper part.
  • If there is a problem with the drum or bearings, then you will have to completely disassemble the machine.

Step.by.step instructions for disassembling the washing machine

It is kept in the right position by several screws (with them you can handle a cross blade) in the upper rear panel. When you unscrewed them, on the lid should be pressed on the front side, and then raise it up.

To extract this element, you need to find a special button made of plastic, which, as a rule, is in the center of the tray, and after you press it, pull the element on yourself and the dispenser for gels and powders will come out.

This part is attached to a pair of screws. One of them is located under the chopping cutter, and the second. in the opposite part of the panel. Do not forget that you should handle it extremely carefully, but it will be better if you put it on the upper part of the machine or bring it to the hook.

It is needed for service and extracting small items that accidentally got into the tank during washing, so there is nowhere to remove it is easier. click on two latches on the sides and on the third, which is in the middle.

First you need to remove the rubber clamp located on the loading hatch. It is held by a small spring that needs to be applied.

Next, the cuff must be pulled out in a circle (to help you plows and screwdrivers). If the cover interferes, you can remove it by unscrewing only a few bolts, but if it does not bother you at all, you can not touch it.

Next, find all the locks that hold the front panel.

In addition to them, there are still hooks on the panel and in order to remove them, the part should be slightly lifted.

The power supply connector is extracted from the Luke lock devices, and now the panel is completely at your disposal.

Everything is much easier here, because to remove this wall you only need to unscrew the fixing bolts around the entire perimeter (which may be quite a lot).

Vertical load

The unit should be disconnected from drain, electricity and water supply.

    Control Panel. Neatly, using a screwdriver, pry the upper control panel from all sides. Pull it up, then towards the posterior wall, and then tilt it at an angle convenient for you so that you can freely work with wires.

Be sure to photograph the locations of the wires in the state of disassembly “before”. Next, everything is twisted and dismantled. On the printed circuit board are all the elements that are unscrewed for further disconnection of the fastener module.

How to disassemble washing workers of various brands

How to disassemble the Samsung washing machine

In the washing machines of the manufacturer Samsung, the tray for loading detergents is attached to two self-tapping screws.

Ten in Samsung machines is located under the front cover of washing machine, below the boot tank.

How To Replace The Door Handle On A Hotpoint Washing Machine

How to disassemble the Ariston washing machine

The biggest trouble that can befall the washing machines of the manufacturer Ariston is a breakdown of oil seals and bearings. The manufacturer tried to make these parts could not be repaired, although if you have golden hands, then this is not an obstacle.

The tanks of Ariston cars are whole, so to replace the oil seals you will have to completely turn off the tank, or simply put it, cut it.

How to disassemble the washing machine Atlant

It is very convenient to get the drum in the Atlant typewriter through the upper hatch, not forgetting to remove the counterweight in advance and dismantle the upper control panel. The drum in this model is understood by two halves, which are tightened in working condition with bolts. Such a model in terms of repairing the tank is very practical.

How to disassemble the Electrolux washing machine

The front wall in electric luxury can be removed, and it will also provide access to all main nodes.

“To replace (repair) bearings and oil seals, you will not need to dismantle the entire tank, since these parts are on removable supports.””

To remove the front wall of the washing machine in LG, you will need to unscrew the hatch cover, and then remove the cuff. It holds a clamp, which will become a screw in one place.

This screw can be found if you lift the edge of the clamp with a screwdriver and will inspect everything, moving in a circle.

For a simpler extent of the drum, remove the upper weight from it first.

How to disassemble the Washing machine Indesit

Experiment. Complete Disassembly. of Ariston Washing Machine

The back of the Washing Washing Party Indesit is a small oval wall that is attached to six bolts. The upper cover is inserted into the grooves, and to remove it, you will need to unscrew two bolts, and then understand the detail on yourself, while without raising it.

Ten is under the tank, and access to it freely opens through the back of the device.

How to remove a lock in a washing machine?

In any situation when the indicator is the key or lock on the washing machine, the first thing you can try to remove the lock by pressing the program launch button, holding it for 5 seconds. After that, the system board is rebooted, the lock is usually disconnected.

  • Disconnect the car from the network by pulling out a fork out of the outlet.
  • Holding the door tightly, unscrew the loops of its fasteners
  • Bending the cuff, remove the clamp using a screwdriver.
  • Remove the edges of the rubber in a circle and season the drum.
  • Pull the inner clamp a little up and away from the tank.

How to remove rubber gasket in a washing machine?

Gently put forward the front of the rubber gasket. We are looking for a mounting mark indicating the required arrangement of the cuff to the washing machine drum (most often there will be a characteristic ledge). Celebrate the marker with a retaliatory label on the case. Pull the elastic on ourselves and take it out of the recess.

Dismantling of smell HotPoint Ariston. Preparation for work

When repairing with your own hands, you need to observe safety precautions. Be sure to turn off the equipment from the network, as well as block the water supply valve. Usually, the cm cm is only disassembling a complete disassembly of the cam. But this knowledge will come in handy even when replacing the heater. The brush brushes. cleaning the pipes and other elements.

Before disassembleing the “hotpone-ariston” washing machine, it is necessary to free enough space. First of all, turn off the communications from the body:

  • Prepare a water collection container.
  • Remove the drain hose from the sewage site or siphon.
  • The tension hose can also not be removed from the case, but simply disconnected from the pipe.

Fix the hoses with clamps on the back wall. Now drain the remaining fluids from the tank so that when turning the machine, the moisture does not get to the electronic components.

Put the machine to the center of the room. You should be convenient to approach it from all sides. Pull the blanket or towel on the floor. Excellent! The preparation is over. Find the necessary tools for dismantling the fasteners in advance. We need:

  • Schloven screwdriver.
  • Pliers.
  • End key with a set of heads.
  • Rozhka key.
  • Wooden bar.
  • A hammer.
  • Kryazuvka for metal.

How to remove the top cover of the Ariston washing machine

Without dismantling the top, it will not be possible to remove the rest of the walls. Therefore, unscrew the mounting screws at the back, move the lid back and remove from the place.

There is a large counterweight on top, which covers access to other details. Twist its bolts and remove the stone to the side.

Service hatch and front panel

Instead of the back wall in Ariston washing rooms, a small hatch is provided. Remove it simply by unscrewing self.tapping screws around the perimeter.

Training

First of all, it is necessary to disconnect the washing machine from all communications:

It is advisable to drain the remaining water from the tank in advance by means of the drain filter or a tube near it. Next, you should prepare free space for the location of the very washing unit and units removed from it and components.

We prepare the required tools. To disassemble the Ariston washing machine, we will need:

  • screwdrivers (cross, flat, hexagonal) or electric screwdriver with a set of bits of various types;
  • Otrous keys to 8 mm and 10 mm;
  • a basket with heads on 7, 8, 12, 14 mm;
  • Passatigi;
  • Kusachki;
  • a hammer and a block of wood;
  • There will be no excess pulp for bearings (when the wrestling of the washing machine is carried out for the sake of replacing them);
  • hacksaw with a canvas for metal.

How to disassemble the washing machine Zannusi?

To disassemble the Zanussi washing machine, you need to remove the top cover of the washing machine. To do this, unscrew the two screws on the back of the washing machine. After unscrewed the screws pull the lid over ourselves.

How to clean a washing machine with vertical loading

First pour 2-3 cups of vinegar into the water and let the machine mix the solution for a couple of minutes. Then add half a glass of baking soda. Let the components react, and then turn off the device and leave it to soak it.

Dismantling of the tank of the washing machine Ariston

To begin with, it should be noted that Ariston “insidious” equips all its cars with a non.devastated tank. They believe that during a breakdown you need to change this whole block. And pay for this price approximately the equivalent half of the cost of the entire washing machine. But they think so. The tank, in general, is not cast, but as if soldered from two halves.

Having looked closely, it is easy to see the seam on which he was fastened. Here on this seam without a shadow of doubt, you need to cut the tank using a hacksaw. We put the empty part to the side. From the second half, you need to knock out a steel drum of a washing machine using a bolt and hammer.

Bearings are taken out if necessary. The cross.cutter of the drum, in case of damage, is removed and replaced by a new.

ARISTON washing machine is disassembled. Approximately 20 holes are drilled in it for the back of the tank. The edges of the halves are smeared with sealant and tightened with bolts. Not particularly and difficult. And all this is quite possible to do it yourself. Nothing can be compared with the feeling when he did something with his own hands.

DISROUND DIY ARISTON Washing Machine

The washing machine Hotpont Ariston stopped working. I need to repair. But in order to start repairs, you need to first figure out how to disassemble a “home assistant” so as not to harm her even more. DISROULD ARISTON washing the washing machine with your own hands, or rather the nature of such a parsing will depend on the adventures of the breakdown. In some cases, you can do only partial disassembly, but sometimes you have to dismantle everything to the screw. About how to analyze the washing machine of the brand hotpont Ariston, read in the article.

So, after all the work done, the tank is kept only on hooks-pendants. To get the drum from Ariston washing machine, lift it up, removing it from hooks. Another difficulty. If you need to extract the drum from the tank, it will need to be cut, because the drum and a tank of the HotPoint-Ariston washing machine do not formally understand-this is how the manufacturer of these units conceived. Nevertheless, make their analysis, and after that it is possible to collect with appropriate dexterity.

If the washing machine is produced in the middle of the bundle glued in the middle, if it is made in Italy, then the tank is much easier to cut the tank. Everything is explained by the fact that in Italian samples, tanks are glued closer to the cuff (ring seal) of the door, and it is quite simple to saw them. In the washing machines of Hotpoint Ariston Aqualtis, just such are installed.

  • Take a hacksaw with a canvas for metal.
  • Install the tank on the rib. Start the saw from a suitable side for you.
  • Cutting the tank along the contour, remove the upper half.
  • Turn the lower part over. Pick up a rod with a hammer to knock out the drum. The tank is disassembled.

The stages of disassembly of the machine are clearly demonstrated further.

  • Several screwdrivers (cross.shaped and slotting are required).
  • Electric screwdriver.
  • Several hexagons.
  • Passatigi.
  • Hammer.

Some types of compounds by coincidence are simply “attached”.

In order for you to unscrew such an old screw, you will need a special liquid that almost all motorists have-WD-4O.

In addition, a small pelvis for draining the remaining water from the hose and several rags with which you can wipe the internal details, wipe your hands and quickly collect water spilled outside the pelvis will never hurt you.

Tip: If you are not analyzing washing machines every day, the best option would be to photograph each showdown stage. This will be a reliable guide to the final assembly so that you do not mix anything and successfully launch your repaired home assistant.

Devices of any manufacturers like Ariston, Indesitis or other machines have a similar structure and the principle of disassembly. Only small differences in the details can be present, which we will talk about later.

The main schemes are predetermined mainly by the type of loading of linen.

First you should de.energize your device, remove the drain hose from it and turn off the water supply into it.

If you know the internal structure of all the elements of your washing machine, then you can guess about which part of the machine there was a breakdown and without wasting time to disassemble the entire washing machine to start doing this from the place of proposed breakdown.

  • Reducing the quality of washing, increased noise during spin and poorly squeezed underwear indicates the presence of a problem in the pump, or is it just clogging of the hose. To eliminate a breakdown of this type, disassemble the machine from below, or just remove the front panel.
  • If you notice that the water does not heat up, then this is most likely a breakdown of Ten. You can find out the location of this part by reading the instruction. As a rule, you need to remove the rear panel, but in some models of washing devices this part may be in front.
  • If the drain occurs longer than usual, then the problem is in the press or pomp. Based on the constructive structure of the washing machine, the part can be located either behind the side panel, or in the upper part.
  • If there is a problem with the drum or bearings, then you will have to completely disassemble the machine.
  • Upper hatch.

It is kept in the right position by several screws (with them you can handle a cross blade) in the upper rear panel. When you unscrewed them, on the lid should be pressed on the front side, and then raise it up.

To extract this element, you need to find a special button made of plastic, which, as a rule, is in the center of the tray, and after you press it, pull the element on yourself and the dispenser for gels and powders will come out.

This part is attached to a pair of screws. One of them is located under the chopping cutter, and the second. in the opposite part of the panel. Do not forget that you should handle it extremely carefully, but it will be better if you put it on the upper part of the machine or bring it to the hook.

It is needed for service and extracting small items that accidentally got into the tank during washing, so there is nowhere to remove it is easier. click on two latches on the sides and on the third, which is in the middle.

We offer to familiarize yourself with how to close the opening in the toilet

First you need to remove the rubber clamp located on the loading hatch. It is held by a small spring that needs to be applied.

Next, the cuff must be pulled out in a circle (to help you plows and screwdrivers). If the cover interferes, you can remove it by unscrewing only a few bolts, but if it does not bother you at all, you can not touch it.

Next, find all the locks that hold the front panel.

In addition to them, there are still hooks on the panel and in order to remove them, the part should be slightly lifted.

The power supply connector is extracted from the Luke lock devices, and now the panel is completely at your disposal.

Everything is much easier here, because to remove this wall you only need to unscrew the fixing bolts around the entire perimeter (which may be quite a lot).

The unit should be disconnected from drain, electricity and water supply.

    Control Panel. Neatly, using a screwdriver, pry the upper control panel from all sides. Pull it up, then towards the posterior wall, and then tilt it at an angle convenient for you so that you can freely work with wires.

| Denial of responsibility | Contacts |RSS