How to tune your Samsung refrigerator with a display

The Samsung refrigerator how to adjust to be cold

In Samsung refrigerators the temperature setting is automatic, but sometimes it is necessary to adjust it Samsung refrigerators deserved trust among consumers thanks to reliability, noiselessness and economy. Particular attention is drawn to the temperature readings of the devices. Manufacturers independently determine what the temperature should be in the fridge Samsung. It is caused by repeated researches and tests.

However, each refrigerator cabinet and freezer has regulators that allow you to regulate the cold within reasonable limits. Further the instruction how to set the temperature in the fridge Samsung two-chamber and zero-frost.

Depending on the model and type, the temperature conditions of refrigerator chambers differ noticeably and decrease from the top to the bottom. The main chamber of the cabinet is set to 3. This figure varies by up to 2 degrees.

Average freezer temperature. about 18 degrees of frost. Here, the adjustment limits are noticeably wider. In addition, many models have a freshness zone, where 5-7 degrees is the norm. precise information about these parameters can be found in the instructions accompanying each specific model.

why does my Samsung refrigerator display OF OF (demo mode)

Interesting: Samsung technologies allowed achieving the result when the temperature in one compartment does not differ by more than 0.3 degrees, regardless of its volume.

Adjustment is made from the control panel, which is connected to sensors inside the unit.

How to set the temperature in a Samsung two-compartment refrigerator

If the Samsung refrigerator is a two-compartment refrigerator, the freezer is set separately, it may have an accelerated freezing function. The action of the intensive mode lasts no more than 72 hours, with an automatic transition to the standard level.

The new unit, once connected, can run for 24 hours without stopping. You can start setting the temperature after the mode has stabilized. It is important that you follow the manual. You can set the temperature by means of the buttons and display or by a manual regulator. How to adjust the mode, informs the manual, developed for each series of refrigerators Samsung.

How to set the temperature in the Samsung No Frost fridge correctly

Unlike the drip defrost systems, the dry sublimation system changes the temperature balance in both chambers. Evaporator placed in the rear wall, it creates continuous ventilation of the chambers. It is possible to set the temperature of the Samsung two-compartment No Frost fridges in the same way as with the drip defrost, using the electronic regulation or manual control.

Let us use the example of Samsung refrigerator with the No Frost system, model RL33 EAMS, to find out why the temperature jumps on the display. Flashing is due to an incorrect temperature setting. Often there are deviations.

  • Temperatures in Samsung fridge above set-point, because door frequently opens in very warm place. If you do not open the circuit for 2-3 hours, the blinking will stop. It is possible that the temperature in these conditions is not achievable. Then there is nothing to do, how to rearrange the setting on the display towards increasing.
  • Not set mode, indicators, notify of the need to set the control points for the correct operation of the system.
  • One of the temperature sensors is defective.
  • System will beep with a loud beep if the door is not properly closed.

It should be noted that Samsung refrigerators are the most reliable, and are adapted to work in the Russian power supply conditions.

The instruction enclosed to the Samsung refrigerator of two-chamber type, how to set the temperature, allows to regulate the equipment independently. When adjusting, follow the manufacturer’s recommendations in order to extend the life of the equipment and ensure food safety.

your, samsung, refrigerator, display

Installation

Once your unit is clean and free of unnecessary things, the moment of the next stage. installation. There are stores that for a small surcharge provide services to install the refrigerator. In fact, in order for the device to work properly and not cause inconvenience, it must be properly installed.

The surface on which the unit is installed must be flat. To prevent the unit from wobbling. For this purpose, there are special adjustable feet on the refrigerator. In the instructions to the units, it is written that it must necessarily stand flat, but there are masters who install them with a slight tilt to the back. In fact. it’s very convenient. No need to exert effort to close the doors. With a slight push they close themselves.

By the way, the way in which the refrigerator stands, absolutely does not affect the quality of its work. All this is done solely for the convenience of owners. So configure your unit so that you are comfortable using it. There are simple instructions and even step-by-step instructions with photos. This is much more convenient, as you will be able to visually understand the installation process.

Samsung refrigerator list of all error codes

If your Samsung refrigerator isn’t working properly, don’t rush to call a service center or a technician. the troubleshooting instructions below will help you fix everything. Below you can see Samsung refrigerator display codes for various common Samsung refrigerator models. Skip the trouble codes and find the appropriate one: you’ll know what might have caused the problem and how to fix it.

Samsung 4e refrigerator error code

This error code indicates that the freezer defrost sensor is defective.In many cases, replacement is the only solution. However, it can also occur due to loose wiring. Check and correct if necessary. In this case the error can be eliminated.

Samsung 5e and 5 refrigerator error code

This error indicates defrost sensor malfunction and/or power outage. First try to clear it by resetting the refrigerator several times. If not working, check defrost sensor and replace if necessary.

Error code 5e signals a problem with the ice maker. Check the unit and harnesses. If necessary, disassemble the unit and check each part separately. If after reassembly and reinstallation you don’t see a positive result, replace the unit.

Samsung 6e refrigerator error code

This is an environmental sensor error that can occur after a power outage. To clean it, press Power Freeze and Power Cool at the same time (or the two top left and right side buttons if the panel on your refrigerator is different) and hold them down for about 15-20 seconds.Usually, this simple reset will bring the refrigerator back to normal.

Samsung 8e refrigerator error code

This error is due to a faulty ice maker sensor. This usually means that the sensor is disconnected or not working. Check the wiring and the sensor itself. You may have to replace the whole thing or part of it. Contact Samsung, discuss the problem and follow their advice.

Samsung 23e refrigerator error code

First, it could be a condenser fan error, signaling a problem with the fan.Please check it and make sure it is properly powered and in working order. Also, check the condenser fan to make sure it is getting power and working properly. If not, repair or replace the fan.

Second, it could be a problem with the control board or wiring harness (if so, the previous action will not work). Check the board and wiring harnesses with a multimeter. It is possible that you need to replace the control board.

Samsung 25e refrigerator error code

It is a defrost error.To fix it, check the defrost timer and/or control board and take action if the problem is detected.

Samsung 33 e refrigerator error code

This error does exist, and it is due to the improper operation of the water heater. In most cases it happens when you move the refrigerator. So if your refrigerator has been moved or changed position in the kitchen, check the water fill tube. The wire wrapped around the tube is a heater for the water fill tube.Now you can begin to clear the error. To do this, press the “Light” and “Energy Saving” buttons simultaneously and hold them for about 8-10 seconds. That’s how you reset your display.

The error can also occur due to physical shock, leading to dents and damage to the insulation. If this is the case, professional help is needed. Whether you can fix it or replace part of the refrigerator (or the entire refrigerator) depends on the extent of the damage. If you scratch your refrigerator, please do not try to fix it cold! This will cause the foam insulation to melt, which can cause irreparable damage to the freezer, not to mention ruined appearance.

Samsung 39 e refrigerator error code

This is an ice maker sensor error, and you can expect three things.

First, the problem may be in and/or around the ice maker itself. Please check all connections around the ice maker (wiring harnesses, plumbing, etc. Д.). The error may indicate a failure of the ice maker itself. It won’t tell you exactly what’s wrong with it, and you may have to take it apart and check every little thing.If you find a problem, contact Samsung and discuss the problem with them. They can provide a new part, even if it is not under warranty.

Secondly, it could be due to lack of water in the ice maker. Check the waterline and its components adjacent to the ice maker. If it does not work, the ice maker may need to be replaced.

Samsung 40 e refrigerator error code

First, take all the stuff out of the freezer and remove the back wall inside.If ice or frost has formed on it, use a hair dryer to get rid of it quickly. Now return the rear panel to its original position. Press and hold down the top right and left dispenser buttons. This will reset the fault codes. If the fault codes do not clear, you will have to install a new defrost temperature sensor and ice blower motor.

Samsung 84c (84e) refrigerator error code

This error signals a locked rotor. If 84E appears on the display, it is a very bad sign: the entire three-speed DC compressor may need to be replaced.The only way to get to the blocked rotor is to get into the compressor. Since this is the sealed and actually the least accessible part of a Samsung refrigerator, it requires professional expertise. Only a licensed person can recover the refrigerant (Freon). Error code appears on digital display due to voltage shift as a result of rotor blockage. When this happens, the inverter control board activates the error code (flashing of the inverter control board is another sign of a problem).Some users say you can fix the error by replacing the inverter control board itself. Over the last decade, many appliances have shown less reliability and have become less durable.

Samsung refrigerator temperature sensors

The purpose of the temperature sensor is to record the temperature in a certain area of the refrigerator. Transmitting the information to the control circuit, it determines the mode of operation of the compressor, changing its intensity.

The desired temperature can be set in each refrigerator compartment.

The following sensors are responsible for the temperature mode in Samsung refrigerators:

All of the sensors’ outputs go to the control circuit, which issues the commands to maintain this condition. The average temperature in the central area of the refrigerator is taken as the basis, because the main sensor is located in this area.

How to set the control panel correctly?

A beaker of water is placed in the center section. This way we will measure the exact temperature of cooling.

If the final temperature is 4, then everything is fine.

If it is 1 or 2 degrees higher, you have to adjust the temperature with the Cooling Power or Fridge button or the thermostat knob.

If there is no button, the thermostat knob with seven divisions is helpful. Turn it to the desired temperature.

There is no point in setting the minimum temperature, since this results in high energy costs and constantly overloading the compressor.

General rules for setting the temperature in the refrigerators

To find out what is the optimum temperature in the fridge and freezer, you should firstly refer to the technical passport, where the boundary parameters of the operating mode of the device are indicated, and secondly, be guided by the type of food and its location inside the cavity. The entire internal volume of a domestic refrigerator is divided into zones: freezer, fresh zone and other compartments. The difference between the two is the temperature level: in the freezer it is minus, and in the fresh zone and other compartments it is low, but with a plus sign.

Setting the temperature in the freezer compartment

The freezer is designed to hold food for a long time, so it maintains a negative temperature. It can differ for each type of fridge, but, as a rule, the range is as follows.6 ºC.24°C. What temperature in the freezer compartment of the refrigerator would be most appropriate determine the purpose of freezing.

Most models have the ability to adjust the temperature in the freezer in increments of six degrees, as evidenced by the marking in the form of stars: each star corresponds to.6 ºC. Most commonly, the limit is.most often the maximum value reaches 18 º C, but there are also such refrigerators in which it is possible to set the temperature in the chamber.24°C for instant freezing. The low temperature in the refrigerator compartment contributes to the longest storage time of fresh meat, fish, semi-finished products, delicate fruits and foods that have undergone heat treatment.

Setting the temperature in the fresh zone

The fresh zone is the part of the internal volume where the recommended temperature in the refrigerator is 0° C. 1° C. It is usually located in the upper part of the refrigerator under the freezer. This mode is the best way to preserve meat, fish and dairy products and prevent the development of bacteria.

At optimal temperatures in the refrigerator, the food has no time to freeze and perfectly preserves its appearance and organoleptic properties. This temperature may be suitable for rapidly cooling drinks such as vodka, juices or champagne, but is not suitable for storing wine.

Setting the temperature in other compartments

All refrigerator compartments below the fresh zone have a different temperature range. So, for example, already on the second shelf, the average temperature in the refrigerator is 2ºC. 4ºC. In such conditions perfectly preserve their nutritional properties processed foods: semi-finished products, confectionery, meat and fish ready products, cheese and sausages, eggs. However, users must be aware that pastry products containing milk products and animal fats are not designed to be stored for more than 36 hours. The same restriction is imposed on cooked sausages and fish products.

The temperature in the refrigerator in the next sector must be between 3ºC. 6ºC. This compartment is for those foods that have undergone high temperature processing, i.e. soups, sauces, stews, boiled pasta and cereals, fresh vegetables and loaf.

At the very bottom of the refrigerator there are drawers: they are convenient for storing fresh fruit. In this part of the refrigerator the temperature must be higher than 5 but lower than 10ºC, because these conditions are favorable for cooling and preserving the fruit and vegetables.

On the door, in accordance with the zoning division of the most part of the refrigerator, shelves are located, on which packaged products, drinks, eggs, dairy products, canned foods, cheese and meat slices, some kinds of medicines (if such a requirement exists in the annotation) can be placed conveniently.

How to set the temperature on the Samsung two-chamber fridge

The task of sensors is to transmit the measured parameters to the electronic control system of the Samsung fridge. Temperature regulation is carried out on the display. In each case, adjusting a certain model, it is necessary to be guided by the instruction on refrigerator temperature setting.

Before changing the temperature, it is necessary to allow time for the thermostat to accept the ambient parameters. After that turn on Samsung fridge, let it work to ensure the parameters set in the factory settings. It is possible to check the correspondence of readings of the electronic board with the help of a glass with water, placed in the center of the fridge and a thermometer.

How to set correct temperature in Samsung No Frost fridge

Unlike drip defrost systems, dry sublimation system changes temperature balance in both chambers. evaporator placed in the rear wall, creating a continuous ventilation of the chambers. It is possible to adjust the temperature of the Samsung two-chamber refrigerators No Frost also as with drip-defrost using electronic regulation or manual control.

It is difficult to do without a fridge for modern man. But quite often it happens that a recently purchased and seemingly quite high-quality unit, which should serve at least a few years, fails after a couple of months. One of the most common reasons. improper temperature mode.

Check Also

What you need to know about TV screen resolution? The resolution of the TV screen plays an important role in the image quality. This parameter will have an impact regardless of the type of matrix and diagonal of the technical device.

Samsung refrigerators have deserved trust among consumers thanks to reliability, noiselessness and economic efficiency. Particular attention is drawn to the temperature readings of the devices. Manufacturers themselves determine what the temperature should be in the Samsung refrigerator. This is due to repeated studies and tests.

However, every refrigerated cabinet and freezer has controls that allow you to adjust the cold within reasonable limits. Further the instruction how to set the temperature in the fridge Samsung two-chamber and zero-frost.

Depending on the model and type, the temperature ranges of refrigerator chambers vary markedly and decrease from the top to the bottom. The main chamber of the cabinet is set to 3. This figure varies up to 2 degrees.

Interesting: Samsung technology has made it possible to achieve a result where the temperature in one chamber does not vary by more than 0.3 degrees, regardless of its volume.

Adjustment is made from the control panel, which is connected to sensors inside the unit.

The purpose of the temperature sensor is to record the temperature in a specific area of the refrigerator. Transmitting the received information to the control circuit, it determines the mode of operation of the compressor, changing its intensity.

your, samsung, refrigerator, display

The required temperature can be set in each chamber of the fridge.

The following sensors are responsible for the temperature mode in Samsung refrigerators:

The outputs of all sensors come to the electronic control circuit, which issues commands to maintain the set mode. The average temperature in the central area of the refrigerator is taken as the basis, so the main sensor is located in this area.

The exact cooling temperature is determined. It uses a glass of water placed on the central level of the refrigerator. 4 indicates normal operation. Increase in one or the other direction indicates the need for intervention;

Standard refrigerator compartment adjustment range of 1 to 7 degrees.

Freezer compartment temperature, in two-compartment refrigerators, has separate settings, only the adjustment range here is much wider.

If there is an accelerated freezing function, the freezer reduces the temperature to a minimum of 72 hours. After this mode ends, it returns to normal operation.

This function greatly simplifies the use of the refrigerator. It frees the owner from the need for forced defrosting of the device, saves time, extends the life of operation and allows better preservation of food. Mode is ensured by forced air circulation. An additional fan is provided for this purpose.

Temperature rises more than 3 degrees. Cause. frequent opening of the door at high ambient temperature. To eliminate, you need to close the door and let the refrigerator enter normal mode (2-3 hours);

Not set in temperature mode. Set according to instructions;

Ice tray improperly set (separate indicator). Check and place correctly;

Faulty contacts in the electronic panel. Occurs in case of door relocation. Check connections.

Improperly set temperature in the refrigerated cabinet leads to the formation of ice crusts. In addition to the inconvenience, it is accompanied by an increased power consumption. Abnormal operation is indicated by water leaking into the tray.

These factors cause rapid deterioration of stored products, which not only leads to rotting, but also to drying out. Therefore, at the slightest suspicion of malfunction, you should refer to the enclosed manual.

In the modern world on the market of household appliances more and more new generation models are produced. Samsung No Frost refrigerator is one of them. The principle of operation used in it allows you to forget about the regular defrosting. In order to use this technique correctly, you should study the manufacturer’s instructions, as well as the types of faults encountered and their causes.

Now Change Your Fridge’s Settings With Just a Touch! | Samsung Digi-Touch Cool

Quite common among the technologies of production of refrigerators is the “Samsung No Frost”. It is also called the wind-driven defrost.

Installation and connection

The following rules should be followed when installing the product in the Owner’s Manual:

After your refrigerator is installed, plug it in to a power source. The inner walls of the chambers, shelves and drawers should be washed before placing the food. Turning the knob on the thermostat selects the desired temperature mode. If the touchscreen display is available, the necessary settings can be made on this display.

| Denial of responsibility | Contacts |RSS