Indesit witl 86 control board

Indesit witl 106 control board diagram

Continuing the series of articles on repairing washing machines with your own hands.

All models Indesit witl 106, witl 86, witl 1067, witl 867 are similar to each other and repair problems too.

indesit, witl, control, board

Washing machines can be assembled on ARCADIA or EVO-II electronic board

It depends on your product number of the washing machine.

Add up the numbers corresponding to the blinking LEDs to get the error code.

As an example error F10 add up the sum 82=10 (F10).

We have already published in the past article how to troubleshoot the board EVO-II models WISL by error code.They are similar to each other.

This board is the newest of all, it replaced EVO-II.Installed since 2007.

Wiring diagram of Arcadia control board with end devices

1.Anti-interference filter (power capacitor) 2.Heating element 3.Pump (pump) 4.Hatch locking device 5.Tachogenerator 6.Motor stator 7.Motor rotor 8.Solenoid valve for main wash water intake 9.Prewash solenoid valve 10.NTC (temperature) sensor 13.Water level switch (pressostat) 14.The linear relay of the water level

When plugged in, the door immediately locks (a click is heard) and the hatch lock indicator light illuminates.

Suspect triac breakdown, resistance burnout, motor shorted.

It is necessary to remove the upper lid by unscrewing the self-tapping screws:

Visually inspect the board by unscrewing the fasteners:

Then using a tester test the engine block (6 wires, including 2 red tacho, and 4 black are divided in pairs: the rotor and stator):

Frequent malfunctions related to the motor.It’s a collector motor.

For example, after pressing the start button, the hatch lock goes off and “silence”. The wear of the brushes in many cases can be determined by external inspection or by the intensity of sparks on the motor collector: both under load (there is laundry in the tank of the machine) and without it. in this case, there are abundant sparks (not on the entire perimeter of the collector).

Significant wear and tear on the brushes causes loss of motor power. for example, if the washing machine drum does not rotate with the laundry loaded in it.

Engine control circuit via tachogenerator (ARCADIA module):

Takes infinitely long to wash, constantly draws and drains water.

It is necessary to organize the drainage system properly.The tip of the hose must be between 60 and 100 cm high.

In addition, a jet break must be provided when draining to avoid water being sucked back into the SM.

-All indicators are flashing, except for the prewash, main and rinse indicators.

The culprit is the control unit (module), namely the pulse power supply in it. Wrong signal (voltage) is sent to the board and the lights are blinking.

With front loading, it is located under the tank on the rear side. In upright washing machines under the upper control cover.

To what to pay attention in the power supply to the swollen capacitors C17, C16, C20.

We pick up new capacitors, it is possible on 1000 uF.Take the soldering iron and change.

001.Control knob 002 white buttons on/off/reset 003.control panel white 004 switch bitron 005 function keys 007 display 008 cover knob 010 dispenser release lever 011 dispenser hook spring 012 dispenser release button 016 cover support 018 partition with shock absorber 021 door locking device 022 white dispenser 023 trapdoor cover 026 control panel wiring 027 8-position. potentiometer

Continuing the series of articles on repairing washing machines with your own hands.

All models Indesit witl 106, witl 86, witl 1067, witl 867 are similar to each other and so are the repair problems.

Washing machines can be assembled on ARCADIA or EVO-II electronic board

It depends on your product number of the washing machine.

Add up the numbers corresponding to the blinking LEDs and you get the error code.

As an example error F10 add the sum 82=10 (F10).

We already published in the past article how to remove the fault on the EVO-II of WISL models according to the error code.They are similar to each other.

This board is the newest of all, it replaced EVO-II.Installed since 2007.

Diagramically connecting the Arcadia control board with the end devices

1.Anti-interference filter (power supply capacitor) 2.Heater element 3.Pump 4.Hatch locking device 5.Tachogenerator 6.Motor stator 7.Motor rotor 8.Solenoid valve of the main washing water intake 9.Prewash solenoid valve 10.NTC sensor (temperature) 13.Water level switch (pressostat) 14.Linear water level switch

When plugging into the socket immediately locks the door (heard a click) and lights up the hatch lock indicator light.

Suspect triac breakdown, resistance burnout, motor shorted.

You need to remove the top cover by unscrewing the self-tapping screws:

Visually inspect the board by unscrewing the fasteners:

Ремонт стиральной машины indesit witl 86

Next, use a tester to test the engine block (6 wires, 2 of them red tacho, and 4 black are divided in pairs: rotor and stator):

Frequent faults are related to the engine.It is a collector.

For example, after pressing the start button, the hatch lock goes off and “silence”. The wear of the brushes in many cases can be determined by external inspection or by the intensity of sparking on the motor collector: both under load (there is laundry in the tank of the machine) and without it. in this case, there are abundant sparks (not on the entire perimeter of the collector).

If the brushes are significantly worn, there is a loss of motor power. for example, if the washing machine drum does not rotate with the laundry loaded in it.

Engine control diagram through the tachogenerator (ARCADIA module):

Endlessly long washes, constantly draws and drains water.

It is necessary to properly organize the drainage system.The tip of the hose should be between 60 and 100 cm high.

In addition, there must be a break in the jet when draining to prevent the water from being sucked back into the SM.

-All lights are blinking except prewash, main and rinse lights.

The culprit of the triumph is the control unit (module), namely the switching power supply in it. Wrong signal (voltage) is being outputted to the board and the lights are blinking.

in front-loading models it is located under the tank on the rear side. In the verticals under the top control cover.

What to look for in a power supply for swollen capacitors C17, C16, C20.

Select new capacitors, can be 1000 μF.Take soldering iron and change.

001.control knob 002 buttons white on/off/reset 003.control panel white 004 bitron switch 005 function keys 007 display 008 lid handle 010 dispenser release lever 011 dispenser hook spring 012 dispenser release button 016 lid support 018 cover support with shock absorber 021 door interlock 022 white dispenser 023 trap cover 026 control panel wiring 027 8-post. potentiometer

Indesit 106WITL, W105X, W421WF, WDS1045TX, WI84X, WIDL106EX, WIDL86EX, WISL103CSI, WN421XWS, WDS1040TX

Indesit W43T, W63T, W83T, W84TX, W84TK, W93T, W105TX, W125TX, W145TX

Indesit WIDL106, WIL105, WIL125, WISE127, WISL86, WISL102, WISL103, WITL86, WITL106, WIUN82, WS105TX

Deciphering of error codes of Indesit washing machines and troubleshooting procedures

Also considered a practical example of repair of the EVO-2 control unit in an Indesit washing machine after a power surge

In addition, flashing light extra rinse and lock the door LED

The indesit machine is designed in such a way that allows you to spend minimum time on disassembly, repair and reassembly. The weight of the machine is about 66 kg.

At repair it is necessary to use the service manual and the circuit diagram which you can download under the reference above, but don’t forget, as the machines are constantly improving, there can be differences in their designs.

The washing machine must be switched on and connected to the water supply and sewerage systems exactly as shown and described in the technical data sheet.

It is usually possible to troubleshoot washing machines without disassembling them. We suggest you to read about possible defects and ways of their solution which are presented in the table below.

Machine does not work when turned on 1. Door not closed 2. Circuit breakage 3. Connection cord breakage 4. The plug is faulty 5. The door locking device is defective 6. Power mains isolator switch defective 7. KN knob is in Stop/Dry position 8. Contacts А4-А7 КА 9 are not closed. The pressure switch is defective
Electric drum drive motor does not work 1. Breakage in the connecting circuit 2. Drum drive motor is defective 3. CA faulty 4. EM faulty 5. 90 C temperature relay sensor defective
When switching on, the electric motor hums, but the drum does not rotate 1. Open in the wiring circuit of the motor 2. Open circuit in EM circuit

Parts or connections are leaking

The hatch does not open 1. Door interlock device defective 2. The frame of the hatch locking device is blocked The electric motor of the fan drive is malfunctioning 1. Contacts a-A1 of the drying timer are not closed 2. Fan motor defective 3. Open circuit in connecting circuit

Before starting to dismantle the machine or individual components, the location of the fault must be determined. Power supply circuit for subassemblies and electrical components (motor, heating element, solenoid valve, etc.).д.1) Is passed through the plug, the cord, the hatch blocking device, the pressure switch, the CA and EM contacts. The circuit under investigation, in which the defect is suspected (defined according to Table 1). 1), is broken by disconnecting removable contacts of connecting wires from contacts of EA. Then using an ohmmeter or a special probe check the integrity of electrical circuits of the CA.

Here is the procedure for some of the most typical malfunctions

Drum motor buzzes, but drum does not rotate. Fault location sequence: check the rotation of the drum drive motor in both directions (set the control box to pulse 3) and then in the nesting and spinning mode (set the control box to pulse 24) and, based on the motor behavior in different modes, determine the faulty circuit.

No water in tank in washing mode: check voltage on solenoid valves EV/F# EV/C, EV/A. If there is no voltage, check the contacts of EA AZ-A2 (pulse 1), C4-C5 (pulse 5), C4-C8 (pulse 23); if the EA is set on pulses 1, 5, 23, check the modes of water priming through the corresponding tub: preliminary, main, special treatment.

Replacement of components. Detailed description in service manual. To provide access to the individual components and parts, you must perform the following operations: unscrew the screws fixing the top cover, remove the cover, unscrew the eight screws fixing the back panel and remove it.

Disassembly of components. Deinterfering filter: disconnect the wire from the deinterfering filter, unscrew the nut securing the filter from the machine body, remove the filter.

Flap locking deviceOpen the hatch, remove the clamp, remove the collar from the machine. Unscrew the screws of the hatch lock and the flange, remove the hatch locking device, disconnect the wires.

The commando unitRemove the control box handle, loosen the control box fixing screws to the panel and disconnect the wiring harness.

Drying timer : remove the drying timer knob. Unscrew the screws that fix the timer to the panel, remove the drying timer and disconnect the wires.

Button switchUnscrew the filter: remove the push-button. Disconnect the electric wires by pressing them with a screwdriver from the inside, remove the wires from the pushbutton, unclip the pushbutton from the panel and remove the pushbutton.

Electric Motor: fix the drum of the machine with the transport bolts and sleeves, remove the belt, place the machine on its side, with a pad underneath in order to prevent damage to the body. Remove the grounding screw, disconnect the harness with wires. Loosen the bolts securing the motor to the tank brackets and, supporting the motor, remove it.

Pulleythe belt: remove the belt, unscrew the nut and washer, remove the pulley.

DHDismantle the wires from the heating element, unscrew the fastening nut for the heating element, remove it.

Temperature Controller: remove the temperature regulator knob, disconnect the wires, unscrew the two screws that hold the sensor, remove it.

Temperature sensorWires and plugs are removed, and sensor and gland are removed.

Solenoid valve: disconnect the fill hose from the tee. Disconnect the tee fitting from the valve, remove the wires, remove the hoses from the valve connections, remove the two valve mounting bolts, remove the valve.

Pressure switchPull out the tray: firstly loosen the metal stopper using a flat-blade screwdriver and remove the EA without detaching it from the harness. Loosen the screws that fix the panel to the machine body (two screws inside and four outside the body), slide the panel forward and make the bracket for the pressure switch easily accessible. Loosen the screw fixing the bracket with relay to the car body, disconnect the block with wires from the pressure switch, remove the hose from the connector of the relay.

The shock absorberUnscrew the nut fixing the shock-absorber to the support, take out the bolt, unscrew the nut fixing the shock-absorber to the tank, take out the shock-absorber.

Drain pump: fix machine drum with shipping bolts and sleeves, lay machine on its side, loosen clamp, disconnect hose from pump connection, remove clamp, remove drain hose from pump connection. Disconnect wires, unscrew two screws fixing the pump to the housing, remove the pump.

Drain hose: Loosen the screw fixing the drain hose clamp on the pump connector, disconnect the hose.

Dispenser: take out the tray by bending back the metal stopper with a screwdriver, remove the hoses from the pipette connections, loosen the pipette mounting screws, take out the pipette from the housing, loosen the clamp mounting screw, loosen the clamp, remove the pipe.

The tank and the drum: remove the control box, drying timer, solenoid valves, pressure switch, interference suppressor, terminal block, temperature regulator, front panel with switches, dispenser, complete fan spigot, having previously disconnected it from the gasket rubber of the hatch door pulley. Unscrew the four screws fixing the flange to the upper fan spigot. Remove the fan motor with flange and unscrew the nut fixing the fan, remove the fan. unscrew four bolts fixing the fan motor to the flange.

Drying thermostat: disconnect wires from temperature sensor, unscrew screws securing sensor to upper dryer duct casing, remove sensor.

Heating element of the dryerTo remove the cable tie with the bracket, remove the two bolts and nuts fixing the bracket, remove the bracket. Unscrew the five screws fixing the upper pipe and the parts fixing it, remove the clamp. Disconnect the wires from the heating element, unscrew the two screws fixing the heating element to the upper tube, take out the heating element.

To buy a control module for the washing machine Indesit

The control unit for the washing machine is like the brain for a person. Thanks to this accessory, the unit reads the set programs and starts to execute them. As you have already understood, if this part gets a defect, the machine will not work. Therefore, if you have a similar situation, it is time to buy a control module for the washing machine Indesit and request a replacement, or repair. The module refers to quite vulnerable parts in the washing machine. Therefore, it would be correct to tell you about the situations when you need to replace the above-described component. In this section you will find useful information, and if it is not enough, our specialist will answer your every question.

Control unit of the washing machine Indesit. repair with your own hands

To begin with I want to warn you that I give only checked material, breakage which will be discussed in this article, easily eliminated by replacing a few capacitors. If in your case it didn’t work or you have other problems with the washer controller I’m not sure I can help you. The fact that the brain of a washing machine, a rather complicated detail and even if you see that some diode or resistor is burned out, it does not mean that its replacement will lead to the performance of the unit. The breakdown of one part, often entails a problem with other components, so before you get into the module, think carefully whether you have the skills that are needed in this procedure or not, because this part is worth a lot of money. Next I will speak in a language of question and answer, those who follow my blog, remember that there was a forum and this article is written on the basis of one of the topics, this forum

The essence of the problem is that I have a washing machine and it out of the blue the indication panel flashed, that is, light bulbs on the buttons and blinks rapidly, like color music. I looked in the manual, there is no such thing, all the codes of the error, shustrovshelya not found anything

Apparently, in your washing machine, more precisely in the control unit failed power supply. Remove the control box, if you have a washing machine with a horizontal load, it is located in the bottom left corner of your Cwm, if you look behind, in the vertical at the top under the control panel. You will need to take the module out of the plastic box and inspect the capacities for bloat. I think this will help you. Good luck

Thank you for the advice, I will now try. Removed the board, pretty hard, had to unscrew the hatch behind the washing machine, it is attached to the six screws and try to get it out, though did not work, could not disconnect the wire. As a result, put the machine on its side, on the side where the powder poured, though the water filled the floor, had to first drain the water from the washing machine. Anyway, when I put it on its side, that’s when I had no trouble disconnecting the wires. I wrote this for those who will remove the control module himself. I just took the board out of the box and really, two capacitors bloated, now remove the receiver and solder here. I think an hour later I will write about the result

Fast guy, I haven’t even had a chance to say “A” yet, and he’s already taken the washing machine apart. Take care not to reverse the polarity of these capacitors, it often happens that out of ignorance people put them in for nothing, and as a result the display panel can burn out. Be careful

I’m not going away from the site, I’m not going away from the site. Yay it worked, the washing machine washes like a darling. I wonder how much money I saved. Thank you for your hard work, I do not know how to thank you, I just say thank you

I am very glad that you helped what I advised you. After the publication of this article, in my workshop was a washing machine with a similar problem, also all the indication buttons on the control panel were blinking. The video I made can be seen below.

How to explain the blinking of buttons on the control panel of washing machines Indesit

In addition, I want to make some clarity about the capacitance and voltages, on the capacitors that need to be changed. The fact that these capacitors are designed to quench the pulse, so it is undesirable to put other ratings, that is, if the capacity of 680 uF, then you must put the same, but the voltage can be increased, for example put 16 volts and 680 uF. Do not forget about the polarity, it’s very important. Further we shall consider one more example of similar repair, though it appeared to be unsuccessful, as the processor burned out

Why doesn’t the washing machine turn on?

This topic is also taken from the form that was on my website. The essence of the problem was that the owner of the washing machine Indesit, connected the ground wire, one of the terminals of the heater, the result was what you will read in this paragraph

Hello, help me make repairs to the control module of the washing machine Indesit wisl, control unit 215009152, 02. According to the owner is not properly connected the heater, which burned out a leg of k5 relay, the choke l1, resistors and varistors are normal. The tny264 and uln2003 were replaced, as well as the mains and secondary capacitors. As a result the voltage goes from 0 to 6 volts instead of 12 volts and from 0 to 2 volts instead of 5 volts. In the binding of the chip all changed, the result is the same. Is a short circuit in the transformer possible? Found a schematic of the power supply, can you advise

Judging from the schematic, I am making the assumption that you are torturing the EVO-II board. I do not understand how you can connect the wrong heater, if he phase is not correct, then most likely it was a short circuit, and the result may be that the chip broke through. How is the control panel behaving, what is blinking? Why did you change uln2003, was it clearly broken or are you just guessing? It is not desirable to check the transformer on the board, it’s better to remove it and check. Short circuit on the transformer, quite possible, but it behaves differently, it is unlikely there would be pulses. This behavior looks more like a blown diode, a regulator, a capacitor, or a transistor, and also. You sure the shim is working? Measured from the transformer? And if so, you need to dig into the circuit up to it. There could be any number of reasons. From personal experience, in similar cases, I first of all, check the parts that I marked in the photo, their ratings are below the photo, then unsolder uln2003 and check without it, then under the circumstances. And write about the result

Stabilitron = 4.35V, SMD capacity 0.I don’t know what voltage I take from other boards, I don’t know transistor rating either. Again, from another module, I take it off, I did not need to look for it

Yes, exactly phase on the body was, nothing works on the display unit, t.No DC voltage 12 volt, changed the uln2003 all relays were clicking in time, short on all legs, memory is intact read. sews. All measurements are made with load, 12v flashing light bulb in rhythm, the capacity when measured 280 volts without ripple, removed all the triac, varistors and relays, at the output of a bare BP, not counting the plug, so as not to break 12 volts, without it, the same at 5 volts. I’m not sure about the transistor, the analog for bc817? And where on the diagram is the diode p6ke?

analog transistor, you need to look on the Internet, and in general, I have a lot of junk, I take off the dead boards, and where the diode is. I can not say on the nominal, but in general, it seems that somewhere there is a short. Try a transformer, maybe he really is a short, but usually the ripple, it does not seem. Something here smells like a failure of the processor, and why the transformer ripple goes, not holding in the hands of the circuit board is difficult that something advise. Try changing the Zener diode and transistor

The diode is fixed, D9 in the circuit, I changed the gate, unfortunately, the transistor does not pick up anything of what is

It makes no sense to drip further without it, it is quite possible that it can bleep.

Wizard. Take off the transformer, and in general, I’ve already written that it seems that the chip broke through. After such a blow to the brain, when they rarely survive, it turns out that the phase is practically direct to the microcircuit. I was brought today Indesit with the same problem, in general, blew up the heating element, the owner called the master, he said that the module died. The story goes like this. the customer, decided to make repairs with his hands, changed the heating element and the control module, in short, says that he had the same thing again, they say that it does not work and does not burn. I removed the back cover, and there ground is connected to the heater, just did not look at what kind of board (Arcadia or EVO-2), was in a hurry. On Tuesday I’ll send it to the test bench to see what I can dig up. But I think I will have to replace the microcircuit or the whole module. In general, on Tuesday, I will look

Replaced the t1 to kt3102b, the power supply unit worked after removing the microprocessor. Brain dead, the topic is closed

How much are the services of specialists?

Lack of experience in repairing home appliances is a reason to go to a specialist.

I think only a professional will be able to repair or replace the board. You can find a master by advertising on the Internet or in the newspaper. Perhaps some of your relatives or acquaintances have already used similar services.

The part itself will have to buy separately. If you can repair the board, the master will take it to the service center, because it is impossible to perform such a repair at home.

To reduce the risk of meeting with scammers, you should read the reviews that left other customers. An honest repairer can give you a guarantee and leave all the paperwork on the receipt of the repair.

How to fix Indesit machine control unit?

The main control unit of the washing machine has two boards. One is responsible for the operation of all parts of the washer. The other provides the operation of the control panel. buttons, indicators. and has the appropriate connectors to connect the wiring.

Isn’t the board protected in any way against overloads? Of course, the manufacturer has provided for such cases, the surge protector, which takes the hit during a power surge in the network.

How to check the circuit board of the washing machine and determine the breakdown?

Module for Indesit (Indesit)/Ariston (Ariston) washing machine EVO II- 254297

This module is “basic” for many models of washing machines Indesit/Ariston. Module FREE. “Flashing” to the serial numbers of your washing machine! When ordering a module, please immediately write the serial numbers in a comment to the order!

Additional information:

By what queries people search for this product on our site:

How it works?

The control unit of a washing machine usually consists of two separate boards. The first one implements the control program and is responsible for:

  • the triggering of the drain pumps;
  • door interlocking during operation;
  • control the amount of water and its temperature;
  • controlling the speed of the electric motor;
  • counting down the working time of the program;
  • The customer decided to repair the machine with his hands and changed the heater and the control module;
  • automatic shutdown after a wash;
  • self-diagnosis of the machine.

The second one is needed for a comfortable interaction between a person and a machine. On it there are buttons, controls, indication diodes, displays, additional connectors and other. The interaction of these two “brain hemispheres” occurs through interconnecting wires, buses, and loops.

Repair of washing machines Indesit WITL 86

Indesit WITL 86 washing machines seldom require repairs, because they are rather reliable and qualitative machines. Like all other models of this manufacturer, they very rarely cause dissatisfaction on the part of the owner, perfectly cope with the assigned functions and become a real home helpers with a high service life.

Alas, but such a nuisance as a machine malfunction, sooner or later happens. In most cases it is not a factory defect: breakdowns are usually caused by violation of operating and maintenance rules, as well as physical wear and tear of nodes.

Electronic control modules for Indesit washing machines

Main control module (electronic card) ARCADIA for washing machines Ariston, Indesit, Hotpoint.

Memory chip EEPROM for Indesit WIU80CSI EVOII washing machine electronic module. Used in C00143067. 50% discount on the chip when buying an electronic module.

Control module (block, board) without EEPROM for washing machines Ariston, Indesit, Hotpoint. The chip can be removed from the old board. Also for this board you can separately purchase a selector UN280S and EEPROM chip C00196734 if your machine WIU80CS

Electronic module control (block, board) 5521/U for Ariston, Indesit, Hotpoint washing machine.

Electronic module (block, board) 5602-AR2800 for washing machines Ariston, Indesit, Hotpoint.

Electronic module (block, board) of control for washing machines Ariston, Indesit, Hotpoint. Requires programming (no ext. payment!).

Electronic module (block, board) ARCADIA control for washing machines Ariston, Indesit, Hotpoint. Requires programming (without additional ). payment!).

Electronic module control (block, board) EM13-1 800/1000 rpm. for washing machines Ariston, Indesit, Hotpoint.

Electronic module (block, board) of control with indication for washing machines Ariston, Indesit, Hotpoint.

Electronic module (control card) for washing machines Ariston, Indesit, Hotpoint.

Electronic module, control card for washing machines Ariston, Indesit, Hotpoint.

Electronic control module with display for Indesit washing machine.

Electronic module (block, board) of the control for washing machines Ariston, Indesit, Hotpoint.

Electronic module (block, board) of control for washing machines Ariston, Indesit, Hotpoint.

Electronic module for Ariston, Indesit, Hotpoint washing machine.

Electronic module (block, board) of control for washing machines Ariston, Indesit, Hotpoint. ARCADIA BP PTC. Requires programming.

Electronic module, control unit (sw:01.01.23) for washing machines Ariston, Indesit, Hotpoint.

Electronic module for washing machines Ariston, Indesit, Hotpoint.

Electronic module, control unit (sw:16.01.08) for Ariston, Indesit, Hotpoint washing machine.

Electronic module (block, board) control 3-phase for washing machines Ariston, Indesit, Hotpoint. Firmware is required (without additional software). payment).

Electronic module for washing machines Ariston, Indesit, Hotpoint.

In this section of the catalog you can choose a new electronic module (block) control of washing machines Indesit. If you have been diagnosed with a failure of this particular unit, then in our store you can purchase the Indesit washing machine control unit at a bargain price, and our specialist will advise you on all the issues that may arise. Just call us at (495) 740-59-10 or fill out the order form and we’ll deliver the part you need in the very near future. Please note that most modules require programming. It’s free when you buy the board in our store.

Online store of spare partsCopyright© “Partline”, 2021

All the information presented on this web-site regarding technical specification, stock status as well as price is given for information only and is in no way a public offer, which is defined by provisions of Article 437 of the Civil Code of Ukraine

| Denial of responsibility | Contacts |RSS