Not pumping water into the washing machine

Check the working condition of the pump

After completing the previous items of advice, it is important to constantly monitor the drain pump. It is necessary to connect the automatic machine to the power supply, selecting the option “drain”, and in its absence “spin”. In this situation, the pump begins to rotate. this can be seen in the filter opening. It is necessary to pay attention to how the impeller rotates. If it does not rotate, then you need to replace the pump. The first steps for its replacement are the same as the procedure for cleaning from clogs branch pipe that connects the tank to the pump, but without disconnecting the branch pipe from the “snail”. It is necessary to tilt the washing machine on the back wall, disconnect the “volute” and then disconnect the pump from the supply system and from the “volute” itself. In the majority of washing machines of the new generation are equipped with drain pumps of common types and models, which are on sale.

One more nuance should be noted. There are cases when everything is fine, but the washing machine does not drain water. Removed the filter, checked the pipe and drain hose, there are no clogs, the pump set to the program “drain”, rotates.

There are two reasons why the washing machine has stopped draining water: the first. there was a clogging of the hose for drainage and cleaning is required, the second. the pump has exhausted its resource and only rotates on a “dry”. That is, it can work without water, but with water it jams and does not have enough performance. Therefore, such a pump must be replaced.

Пральна машина, що не зливає воду. нерухома

See also. How to reset the washing machine yourself

Problems with the plumbing

Clogged plumbing is one of the most common causes of problems with the water pressure. There may also be a faulty faucet. Malfunctions often occur during the day when the water pressure is low, especially in large cities, or there are any problems with the water supply. The faucet where the water comes into the machine may simply be blocked or broken.

water, washing, machine

Unfortunately, even the most experienced craftsman can not cope with the head of water. you just need to wait until it becomes strong enough to fill the machine. There is another option, if this problem becomes too frequent and the machine does not pump water. to buy and install a small pump to increase the pressure, which will create the necessary pressure of water. With the faucet, too, everything is simple. you need to check whether it is fully open, whether the valve is not broken. Often the installation of the pump, replacement of the faucet must be carried out with special equipment and therefore it is recommended to call a master.

The problem with the inlet valve of the washing machine

Washing machine valves come in single, double or triple. That’s why some washing modes can work properly, while others have poor water flow into the drum of the washing machine. To check each of the valves, the washing machine must be disassembled. You will need to remove the top cover, right under it you will find the outlet valve, which is located at the top of the back wall. By the number of channels, you will see the coils, which by their cores block and open the course of water. You will also see a pressure reducer that reduces the water pressure at the common inlet. It is a rubber washer, which should also be removed and flushed with water. This must be done very carefully, because if the dirt gets into any internal membrane, then the valve will always leak water and fix it will be almost impossible.

How the coils are set up? Each has a core that rests on a diaphragm with a hole made in the center. If all is well, this system is always closed by a clamping return spring. If power is applied to the coil, the stem comes off. That is why the water flows freely in each of the washing cycles. Thus, by applying electric current to each of the coils and disconnecting the terminals, it is possible to check the flow of water through each channel.

See also  No pressure in thermex water heater

Clogged drains

Blockages are the most common causes of appliance breakdowns. The most effective way to fix the problem in this case is the use of chemicals. They contain an acid or alkali, which has the ability to dissolve accumulated sediment on the walls of water pipes.

The solution is simple: just pour the product you bought into the drain and then pour 500 ml of water into the same drain. After about 10-15 minutes you need to flush the sewer with a lot of water.

In order to make the work of removing the clogs effective, you need to buy the following proven chemical products.

In addition, the filters can also become clogged. During use the filters become unusable, scale builds up on their surfaces. You can tell that this is the cause by an unpleasant odor, as well as slow operation and water drainage. To clean the inlet filter, you need to turn off the faucet that supplies water to the machine. Then follow the following algorithm:

  • disconnect and pull out the hose;
  • Take out the inlet filter and wash it under a strong water pressure;
  • The clean filter screen is inserted back and secured at the edges;
  • reassemble the system and check it for secure connections.

When it is necessary to clean the drain filter, open the bottom hatch, which is located on the front panel, and disconnect the hose. After that put a container underneath and drain off the rest of the water, then take out the filter and wash it. After rinsing, the filter is put back in place, connect a hose, turn on the machine to “drain” mode. It is necessary to clean the filters of the washing machine approximately once every 2 months.

Clogging in the pump

It is possible that the cause of poor water flow in the washing machine is a dirty pump. It can get debris from the water pipe, small objects from clothing, detergent residues that did not dissolve during the washing. If the drainage path in the washing machine has never been cleaned, then over time the dirt has accumulated in the pump.

To disassemble the pump, to remove the clog you need to prepare:

Beforehand it is necessary to choose a container under the drained liquid for the time of pump cleaning. Before starting disassembly, you need to drain the remaining water, clean the filter. Work steps:

  • Disconnect the machine from the power supply.
  • Press the latches of the hatch cover, located on the front panel.
  • Remove the filter.
  • Place a container and drain the liquid into it, clean the filter.

To clean the pump, you need to disassemble it. The casing is made up of two parts, the volute and the pump and impeller. The impeller must be inspected because it collects hairs and threads which impede the function of the unit. The volute also needs to be inspected to remove debris. After that, the whole construction should be reassembled, run the program. You should listen to the machine, the noise it makes, monitor how well the water is pumped out.

If after the cleaning of the pump is again observed underflow, then the pump needs to be replaced. On this issue it is better to refer to the service for washing machine repair services.

Frequent Causes of Washing Machine Failure to Draw Water

The main situations in which such a problem occurs are the following:

  • Stop valve is blocked. If the automatic machine is installed correctly, it is connected to the water supply through its own faucet, open it, then the liquid begins to pour The washing machine does not pump water when the hatch is open. Firmly close the door, check whether the laundry is not in the way, whether the tank is not overloaded.
  • The inlet hose is kinked. For the machine to work properly, the hose must be positioned loosely, without pinching or squeezing. Disconnect and unclog it and remove the obstruction.
  • The inlet valve strainer is clogged. It is installed for protection against ingress of the smallest particles and suspended solids so as not to damage the membrane of the valve. Over time, the strainer becomes clogged and water does not flow into the drum. You can fix the problem yourself by cleaning the strainer with a fine needle or immersing it in a solution of citric acid for a few minutes.
  • The drain is not properly connected. In this case, the washer does not draw water during the washing cycle, because it can not drain the old. Usually an indicator of such a malfunction is a characteristic hum of the motor.
See also  How to unscrew the legs of a washing machine

Pay attention! If the machine pours liquid, but very slowly, and then gives an error of water intake, the cause is most often a clogged filter, clogging.

Filler hose and fine filter on the washing machine

Fill hose can only be screwed on by hand. It is not necessary to grasp the pliers or wrench. Unscrew it the same way. The rubber seal prevents water from leaking. Hold the hose over the bathtub with the swiveled end. Open the ball valve carefully. a strong jet is expected. If everything is okay, return the valve to its original position and grab the thin-nose pliers.

Filling hose and fine filter

Carefully remove the fine filter from the washing machine. Located right behind the hose, in front of the inlet valve. The fine filter looks like a thimble with a ridge on the outside edge. Grasp the ledge. Do not mix up the outer casing as the ridge is convex. If you get it mixed up, it’s hard to get it out and put it back in correctly.

The filter should be rinsed under running water. If the part is clean, the cause is different. You have to disassemble the washing machine.

If the washing machine does not hold water and drains it immediately after dialing, you must first determine the cause. Among the full list of defects can be both not very serious, which can be easily and inexpensively eliminated, and more complex failure, requiring the intervention of a wizard.

The main causes are:

  • The wrongly connected washing machine;
  • clogging or breakage of the inlet valve, its parts;
  • Pressostat malfunction caused by clogging, contamination of contacts, coil burnout, etc.п.;
  • Breakage of the electronic module (program failure, burnout);
  • Trouble with the integrity of the tank.

Incorrect installation and connection of the washing machine

First, it is worth checking the most simple and common cause of such a phenomenon. The drain hose may have been installed the wrong way round, or the old appliance may have been moved to the wrong place. You can verify this by external inspection.

You can fix this problem on your own. For the convenience of users, the equipment is provided with a plastic loop. It is attached to the back of the housing. It is sufficient to put the drain hose through it, and it is automatically positioned at the correct level.

Inlet valve

One of the causes of the fact that the machine constantly draws and drains water, is a faulty inlet valve. Its main function in the device is to block the flow of water. In this situation, there are several possible options. The valve may have failed completely or the problem may be with its diaphragm, which acts as the main component of the mechanism. When the diaphragm loosens during operation, water pours into the drum through it. And the valve itself may be in a closed position.

To make sure that the performance of this part is broken, it is best to remove it and test it:

  • This is done by connecting the valve to the filling hose.
  • Then to the coils (their number is determined by the brand of device) voltage of 220 V is turned on one by one.
  • If the valve opens and closes when there is no voltage, then there is nothing wrong with it. Any discrepancy with the norm indicates a breakdown.

You don’t have to buy a new mechanism right away. the problem might be minor and easy to fix. For example, the grid could get clogged or the coil could burn out. In the first case, the grid must be cleaned and replaced, in the second. to replace the burned out coil. In other situations, the best way to repair the washing machine is to replace the part.

Pressostat

The pressostat or water level sensor is designed to control the level in the tank. It regulates the operation of the inlet valve, commands the start and end of the liquid intake. The mechanism has a water column. The pressure in it shows how full the tank is.

Most often the special pressure tube fails, because small debris, sludge, scale can get into it. As a result the pressure gauge transmits the wrong data to the electronic module and the appliance starts working incorrectly. Another cause of failure lurks in the hoses and gates of the sensor. Possible clogs as well as air leaks. These troubles also cause the pressostat to react incorrectly, which causes the washing machine to draw water and immediately drain.

See also  Mini dishwasher without connection to the water supply

Regardless of the source of the problems, the first thing to do is to make sure that it is this component that is to blame for the washing machine malfunctioning:

  • Switch off the appliance, pull the plug out of the socket and remove the top cover. To do this, unscrew the bolts, and the cover itself slides to the side and removes.
  • The pressostat is usually attached to the wall of the appliance with a pair of bolts. To disconnect it properly, not only do you have to unscrew these bolts, but also unscrew the small hose and the contacts.
  • Now you can test the sensor with a short tube. It is important that its diameter matches that of the original mechanism tube. Connect the tube and blow into it while listening to the device. Sounds like clicks indicate that it is fully functional, and the absence of clicks indicates that it is time to replace the pressostat.

If the tube of the device is clogged or damaged, or if the contacts do not look right, these problems can be easily solved. In all other cases the sensor should be replaced.

Electronic control module

One of the most expensive and complex causes of the fact that the washing machine does not hold water and constantly draws it, is an electronic module. It is it that regulates the operation of the other components of the design. The unit takes signals from some appliances and sends them to others. There is no definite reason for the breakdown of the unit. certain program settings are knocked down in it, which can cause the machine to make errors in washing cycles. Exactly this problem is considered common for models manufactured by Indesit, LG, Ardo, Candy, etc. The indicators on the control panel start blinking.

There are two ways to fix it, but in both cases you should use the qualified help. The specialists of the “StirTech” service center will be able to carry out the correct diagnostics and find out the extent of the problem. If just failed firmware block, you can configure it anew, but this requires a special device. If for some reason the contacts burned out and the module can not be repaired, it must be replaced with a new one. Call us at 8(499)113-60-22 and leave a request for a master visit.

Problem with water supply system

If the washing machine dials water very slowly, then the reason for this may be in the plumbing and a weak head.

It is likely that the water can not come into the washing machine because of unscheduled works of public utilities or burst pipes. Many people immediately think that it is a technical problem and forget to think about other possible causes.

If the water supply is all right, while the pressure is also stable, then it is time to pay attention to the hose through which the water flows into the washing machine.

It happens that the water tap simply forget to open. The hose may be fractured or badly bent. Check the entire length.

Cleaning the filter and hose from a clog

If nothing unusual was found, the reason for this may be in the hose filter, and therefore the next step is to check it. The filter may simply be clogged, which can lead to a complete shutoff of the water supply or a very slow flow.

But cleaning the filter alone will not be enough to ensure a steady flow of water. To do this, take care to clean the hose itself as well.

Using a powerful head of water, you can effectively get rid of any dirt and clogs, without even having to bother to prepare special solutions of detergents.

Even if it’s time to change the filter, it will cost very little.

| Denial of responsibility | Contacts |RSS