Replacing the bearing in a Samsung washing machine

How to change the bearings in a Samsung washing machine

Before starting the repair work, it is necessary to disconnect the machine from the electric network to avoid the possibility of electrocution. After that, unscrew the water supply and drain hoses, pulling them slightly forward.

Dismantle the pulley and motor

To solve the problem of worn seals and bearings, remove the motor and pulley of the washing machine. To do this, you must first remove the drive belt by screwing the pulley and pulling the belt forward.

Then fix the pulley by inserting a strong pin into it. It is possible to tighten the pulley if you unscrew the screw that fixes it. Pulley can be removed from the shaft by rocking it slightly and pulling it toward you. It is not necessary to remove the heating element. Although, this is the time to look at what is the state of the heating element. If there will be a thick layer of scale on it, it is better to remove it.

The motor can be removed by loosening the bolts that hold it in place. You will need to remove the branch pipe. It is easier and simpler to do this through the bottom of the machine, turning it on its side.

Disassembling the top cover

At the back of the machine are 2 screws, through which the cover is attached to the body. After unscrewing them, the lid will move back a little. After that it can be lifted and removed.

replacing, bearing, samsung, washing, machine

Some models of Indesit washing machines are equipped with special plastic latches that fasten the cover. In this case, it is enough to unfasten them, which will allow the removal of the top cover.

Removing the drum

The next step in replacing the packing and bearings is to remove the drum. To do this you need to take out and pull the tank by pulling it forward. All the eldestit models are equipped with a one-piece tank. In order to be able to access the drum, you will have to split the tank into 2 parts. You can do this by sawing it with an angle grinder or metal saw.

Before you start sawing the tank, you need to make a final decision about how it will be reassembled. To do this, you need to make several holes on its surface for bolts, with the help of which the tank can be assembled into a complete structure.

After disconnecting the drum from the tank, experts recommend inspecting it for damage. Also check the condition of the seal located under the drum. If it is stretched and has cracks on the surface, it is better to replace it.

Remove and replace bearings

Now it is time to change the oil seal which is serving a protective function for the bearings. A screwdriver can be used to pry into the packing. This may be difficult to do. It will be necessary to use a hammer and chisel, gently knocking out the bearings, tapping on them in a circle.

If you can not do it yourself, you will have to go to the service, where with the help of special equipment the collar will be pressed out of the bearings.

After successfully removing the seals and bearings, clean and lubricate the place where the new parts will be installed. It is recommended that a special sealant be used for greasing.

The new bearings and the lip seal can be reinstalled using a hammer and wood shoe. This will considerably reduce the force of the hammer blow, preventing cracking of the bearings and damage to the oil seal. The main direction of impact should be on the edges of the parts. The oil seal must stand on the bearings. After this, it remains to assemble the washing machine eldesit in the reverse order.

To ensure that the replacement does not cost too much, it is advisable to follow these rules of operation:

  • Pulley operations should be performed carefully, without sudden jerks. It should first be easily rocked to the sides, and then pulled forward. Otherwise, the pulley can be broken;
  • With prolonged use of the machine its bolts can get stuck, which complicates their unscrewing. If force is used when unscrewing the bolts, the heads of the bolts can be torn off. To avoid this you should spray them with WD-40;
  • When dismantling the tank lid you can break the wires of the temperature sensor;
  • Perform the assembly of the washing machine should be carefully, remembering to connect all the sensors.

Following these simple rules will help to avoid additional costs for repair work.

Preparation for repair

To replace faulty bearings, the owner of a Samsung washing machine will need to buy new ones, as well as seals and special grease. Usually the manufacturer’s service centers and specialized stores offer repair kits, which have everything you need. You can also order them via the Internet. To correctly choose the right parts, you should tell the seller the brand and model of the washing machine.

In addition to spare parts, to replace the bearings, you need to prepare various tools. To perform the repair you will need:

After all necessary assembled, new bearings purchased, it is necessary to unplug the washing machine, remove the water inlet hose and disconnect the appliance from the sewer. Next, you need to move the Samsung washing machine to a spacious place and prepare one or two tables to place the removed nodes and panels.

How to choose bearings?

To replace a faulty part, you must first buy a new one. Bearings can not be repaired, so they are replaced. The glands are also replaced and the lubricant is restored. All this is purchased in a kit, which is selected according to the model of the washing machine.

Learn the exact name of the model can be found on the stickers that are located near the hatch and on the back of the washing machine. This marking is used to select the repair kit. For this purpose, it is convenient to use special tables. If there is no information on the desired model, you can find information on the official website of the manufacturer. If in doubt, you can take old bearings as an illustrative example. With this pattern, it will be easy for a salesperson to find a repair kit that fits correctly.

Order of replacement

Removed from the tank bearings are carefully inspected for mechanical damage. If there are serious defects, it is necessary to replace the element with a new one. In place of the bearings knocked out with a chisel and hammer the serviceable parts are mounted and their fixation is checked.

Disassembling the washing machine

First we need to remove the upper part of the case (cover). It is attached with two screws on the back side. Once you’ve unscrewed them, you need to slide the cover toward the back of the housing. And then we take it off. Then completely remove the dispenser of the machine. On some models we need to push down on the latch to remove the dispenser. Then we need to remove the control panel. To do this we unscrew the fixing screws. The panel can be gently placed on the side of the case.

Next, open the hatch and remove the outer collar. There are different collars. Some can be removed with needle-nose pliers. Others can be removed with a slotted screwdriver. Once the clamp is removed we need to separate the cuff from the front part of the housing and tuck it inside the machine. That way it won’t get in the way.

Then unscrew the clamp. It is fixed with two screws. Twist them off and put your hand inside between the cuff and the wall to separate the blocking device from the wall of the machine from inside. Let’s remove all the rest of the fasteners and remove the front part of the body. In the same way we remove the back of the case beforehand, so that you don’t have to bother with it again.

Then we disconnect the hopper of the dispenser with a pipe from the tank of the machine. To do this, we need to remove everything in the way and loosen the clamp. Put it where it doesn’t get in the way. Then we need to remove the counterweight (if it’s in the front). If it is in the back, let’s get to it and take it off by all means. Usually the counterweight is fixed with screws. These bolts we will unscrew with a screwdriver.

Next we get to the heating element (heating element). Most models have it on the back. Some have it in the front. Before removing it, let’s make a photo of wires, so that later we can connect everything in the right order. Then let’s take off the fasteners of the heating element. Usually it is attached to one nut. Loosen it and press in the screw. Then using a flat tool (e.g. screwdriver) pry up and remove the heating element.

After that remove the tube that is attached to the tank. We have already learned how to disconnect the clamps, so we do it without any problems. Then remove any wires that may be attached to the tank.

Approach the machine from behind and remove the drive belt. Next, disconnect the connector wires leading to the motor of the machine. Then we twist the self-tapping screws which fix the engine. Then we take out the motor by pulling it to our side.

Then we should unscrew the screws that fix the shock absorbers. And separate their lower parts from the wall of the machine. The only thing left is to remove the springs. And the tank can be taken out. All this should be done carefully so as not to drop the tank.

Pull the tank out

We have found the tools, bought the accessories, you can prepare a place for comfortable work, and then proceed to disassemble the washing machine Samsung with your own hands. In the second step, our task is to remove all “unnecessary” from the washing machine, so as not to interfere with the dismantling of the tank. It must be done in such a way that nothing is broken or lost, so put all the removed parts in separate piles. So let’s start with the disassembly.

First, remove the top wall (cover) from the machine. To do this you need to unscrew the two fasteners that hold this cover. They are at the top of the back wall in the corners. Then you need to put both hands on the top wall and pull it toward you, then lift it up.

Then take out the powder cuvette. This is to prevent water from pouring out of the cover and flooding the electronics when we tilt and turn the machine. It is easy to remove the cuvette:

  • open it as far as it will go;
  • with the finger of one hand press on the “tongue” of the central section;
  • at the same time, lift the cuvette slightly with your other hand and pull it toward you;
  • If it is OK, the flask should pop out and stay in your hands.

Having removed the powder cuvette, unscrew the hoses supplying water in its sections, as well as the hose through which water and powder enter the tank. Remove the hoses carefully so as not to damage the clamps. Unfasten the clamps using pliers, and then pull the hoses.

Next, our task is to remove the obstructing us a large upper counterweight. For this take a head of suitable size and unscrew the two fasteners, then gently holding the counterweight, remove it and put aside.

Important! Unscrewing the last bolt with your hand, be sure to hold the other hand counterweight, because it is very heavy and can slip to the side, damaging important parts of the machine Samsung.

Now moving on to the front wall of the washing machine Samsung. We need to remove it with our own hands, but to do this we will have to properly remove the rubber cuff, without damaging the element of the system locks the hatch. What must be done?

  • Unscrew the two fasteners of the device blocking the hatch.
  • Then disconnect its sensor, so as not to break the wire when removing the collar.
  • Screw the bolts back in so we don’t lose them.
  • Take a screwdriver, find the steel cable clamp at the base of the cuff and pick it up.
  • We pass a screwdriver under the clamp, pulling it away from the groove. Our task is to find the fasteners of the clamp in order to loosen them and remove them.
  • Loosen the bolt and remove the collar from the cuff.
  • Slip your fingers under the sunroof cuff and gently pull it towards you.

It is possible not to pull out the collar all the way, the main thing is that it does not interfere with the removal of the front wall. Leave the front wall alone for a while. Now we need to put the washing machine Samsung on its side to remove its bottom. To do this, unscrew the four fasteners that hold the bottom cover and remove it.

Now for the electrics. It is necessary to unhook all wires from the electric motor of the washing machine Samsung, as well as from the drain pump. It would be a good idea to make a video of the electrical work, since it’s easy to get tangled up in the wiring. If this is not possible, you can just make marks with a marker.

Samsung Front-Load Washer Disassembly, Repair Help

Pay attention! The contacts that connect the wire to the unit’s sensors are pretty flimsy, so try to act accurately. If you find a burned wire or contact it should be replaced immediately.

Proceed to dismantle the racks on which the washing machine tank lies. To do this, unscrew the four fasteners that secure one end of the rack to the tank and the other to the bottom of the cabinet. In the lower part we will not unscrew anything else except the engine, the drain pump will not bother us, we only need to disconnect the pipes from it.

replacing, bearing, samsung, washing, machine

Leaving the machine on its side, go to its upper part. Now we need to dismantle the fill valve with sensors and pipes. Disconnect the wire going to the sensors of the valve, and then unscrew the bolts that hold it. Then remove the valve and set it aside. Disconnect counterweights, which are four springs on which the tank is suspended.

The way for the tank out through the top case is almost “cleared”, now the front panel and wall can be removed. Unscrew the five screws that hold the front panel and remove it. While doing this, try not to damage the control unit, ripping off the wires. Next, unscrew the front wall, unscrewing a total of 10 fasteners, and remove it to the side. In front, under the tank we will see another small counterweight, it also needs to be unscrewed, so as not to interfere.

How to Change the Bearings in a Washing Machine

All that could prevent removal of the tank, we unscrewed, now you need to very carefully remove the tank from the housing of the washing machine Samsung along with the motor. Removal of the tank, drum and motor is a very responsible moment can hurt some of the contact and then the work increases. Turn the tank, remove the belt from the pulley, and then unscrew the pulley itself with an Allen wrench.

Replacement Preparation

So, you are convinced that your washing machine needs bearing replacement, and you are confident that you can do the job yourself without bringing in a handyman. Where to start?

Before proceeding to repair, you need to buy a new set of bearings, including the packing. It is best to choose original manufacturer’s replacement parts that match your model, even if they will cost more than analogs.

replacing, bearing, samsung, washing, machine

A new set of bearings should include a rubber gland

  • flathead screwdriver and Phillips head screwdriver;
  • A chisel or an impact screwdriver;
  • hammer;
  • pliers;
  • wire cutters;
  • socket wrenches;
  • WD-40 detergent;
  • glue;
  • Sealant.

Before you disassemble the housing of the washing machine, you need to free up enough space for work and for the storage of parts. Unplug the washing machine from the mains, disconnect the hoses, move the equipment away from the wall so that there is access to it from all sides. If possible, remove it to a storage room (pantry, garage) in case the repair is delayed.

Replacing the bearing

The bearings and seals are on the back of the tank lid. To replace these parts, they must first be knocked out of their seats.

  • The outer bearing is the first to be removed. This will require taking a chisel and hammer and light blows in a circle, not allowing warping knock out the part. You only have to strike the outside of the bearing to avoid damaging the seating. It is forbidden to hit only one point, there must be several places to hit, otherwise the bearing will be tilted or stuck in the sleeve, resulting in additional complications.
  • Similarly, the second, smaller, bearing is knocked out by turning half of the tank upside down.
  • It is also necessary to remove the old bearings.
  • After the worn parts are removed, you need to wipe the inside of the sleeve dry with a clean rag, removing dirt and grease residue. Then the new grease supplied with the bearings must be applied and the new seals fitted.
  • Now you need to replace the bearings. Start with the inner one. It should be installed in the sleeve, make sure it is level, and then hammer it into the interior. To do this, take a chisel and hammer and beat evenly in a circle, avoiding warping. Only the outside of the bearing should be hit.
  • Once the inner bearing is in place, flip the half over and drive the outer bearing in.

Bearing replacement is complete, you can proceed to reassemble the machine.

Removing parts that prevent getting to the tank

The next action is to remove the upper counterweight. a concrete block that gives stability to the CMA. Next, the dispenser is removed by unclamping the clamp that secures the spigot to the tray. The tubes of the inlet solenoid valve are also connected to the powder hopper. You can unhook them from the cuvette or remove the container along with the valve. Removing the filler valve is simple: unscrew its fixing bolt, disconnect the supply wiring. Pull out the element together with the dispenser. Next:

  • disconnect the water level sensor pipe from the tank;
  • Remove the front counterweights from the machine;
  • Unfasten the connectors of the heating element, pull out the heater;
  • Loosen the clamp on the discharge nozzle, disconnect it from the tank;
  • pull down the drive belt;
  • Unscrew the bolts holding the motor, pull out the motor;
  • loosen the clamp and unfasten the pressure chamber attached to the tank;
  • unscrew the screws of shock-absorbing springs;
  • lift the tank to remove it from the hooks and remove the element from the housing.

Next, put the tank on a flat surface, remove the manhole cuff by unclamping the inner clamp. After removing the pulley, unscrew the central screw. Unscrew the bolts around the perimeter of the connecting seam of the tank, divide it into halves. Remove the drum, so the bearings and oil seal are in front of you.

| Denial of responsibility | Contacts |RSS