Replacing the plum hose of dishwasher Hotpoint Ariston. Problems with wiring

What can be done yourself

Perhaps you have chosen a delicate program. In this case, Ariston washing machine will stop with water, there will be no squeezing. Cancel this program and start a water drain program.

Take the hose from the siphon to the bath or sink and turn on any program on the washing machine. If the water begins to merge, sewage is clogged. You need to call plumbing.

Due to garbage entering the filter, water does not leave the Ariston washing machine. You can clean the filter yourself:

  • Disconnect the washing machine from the network, lay a towel under it or substitute some kind of container, as water can leak up to 500 ml.
  • Unscrew the filter cover (usually it is on the right side from the bottom of the machine case).
  • Wait until the water drains, then remove the filter and clean it under running water.

When to contact the service

Когда трубки прессостата забиваются либо он полностью выходит из строя, блок управления не получает информацию о количестве воды в баке и не начинает сливать воду.

replacing, plum, hose, dishwasher, hotpoint, ariston

Smells water, the drain pump does not work. A plum error may occur on the screen. This is a F04 or F07 code.

Due to prolonged use of the machine, a breakdown of contact groups could occur, wiring.Wipe. And due to moisture hit, the contacts could be oxidized.

Can be damaged due to voltage jumps, water from the board, excessive vibration. As a result, radio elements fail, contacts are burned or oxidized.

In addition to the filter, the blockage could occur in: drain pump, hose, pipe. Due to garbage, water does not merge from the Ariston washing machine.

Drain pump. This is a case with a impeller and a motor. If garbage enters the pump, the impeller is blocked and the engine cannot scroll it, but tries. As a result, the motor burns out, the impeller blades break.

  • The specialist is de.energizing the washing machine if water remains inside. Drages it through the hose or drain filter.
  • Unscrews screws from the upper cover and bolts from the rear wall to gain access to the level of water level (Pressostate).
  • Disconnects terminals, wires, as well as a pipe from the press. The probe of the multimeter connects to the sensor contacts, check the press to the presence of a malfunction.
  • If the part is faulty, then in its place it sets a new. Collects the machine in the reverse order and checks its work.

How our masters clean the contacts of the washing machine

  • The specialist is de.energizing the washing machine if water remains inside. Drages it through the hose or drain filter.
  • Removes the top cover, removes the dispenser for powder. Disconnects chips with wires, unscrews the fee from the case and takes it out.
  • Depending on the type of pollution, the master selects the cleaning method (dry cleaning, wet cleaning, chemical cleaning) and proceeds to the process.
  • In the case of dry cleaning, the master removes dust and dirt with brushes and compressed air important. with the help of an ultrasonic bath (pours a special solution into a container and leaves a fee in it for a while), chemical. Using alcohol, special solutions.
  • After cleaning, the machine is assembled in the reverse order and tested.

How our masters are re.saving the contacts of the control module

  • The specialist is de.energizing the washing machine if water remains inside. Drages it through the hose or drain filter.
  • Removes the top cover, removes the dispenser for powder. Disconnects chips with wires, unscrews the fee from the case and takes it out.
  • Using the multimeter, it checks all contacts for burnouts, oxidations, mechanical damage (capacitors, resistors, blocks, etc.).
  • At faulty contacts, it solders, in the presence of severe damage, it completely changes them. Then he collects the machine back and tests it.

How our masters clean the drain pump pump

  • The specialist is de.energizing the washing machine if water remains inside. Drages it through the hose or drain filter. If necessary, cleaning the filter.
  • Removes the filter, then unscrews the bottom of the washer and removes it. Disconnects the clamps of the pipe from the pump.
  • Disconnects the entire wiring, twists fasteners and takes out a pump (pump). From the pump disconnects the impeller and performs separate cleaning using detergents.
  • Collects cm in the reverse order and tests its performance.

How our masters change the drain pump in the washing machine

replacing, plum, hose, dishwasher, hotpoint, ariston
  • The specialist is de.energized the SMA if there is water left inside. Drages it through the hose or drain filter.
  • Depending on the configuration of your washing machine, unscrews the appropriate panels to gain access to the drain pump.
  • Disconnects all tubes, terminals, wires, hoses from the pump. Takes out a snail and a pump from the body and puts a new part in its place.
  • All elements are fixed to the previous places, then collects the machine in the reverse order. Launches a washing program to check the work of a new pump.

How to recognize the problem with the replacement of the hose

In standard configuration of Ariston washing machine supplies a waterproof water drain. Despite the density, strength and wear resistance, this material has weaknesses. Namely, it does not withstand long.term influences of high temperatures and does not always demonstrate resistance to aggressive liquid media. Therefore, his wear is a matter of time, although under warranty it should serve up to 10 years.

It is easy to guess about the problems with the drain hose when driving on the rear panel of the machine, as well as on the following signs:

In all cases, the intellectual unit will notify the owner of the machine by the appearance of an N20 error code on the display.

Reasons for replacing the hose in Ariston washing machine

Promotes problems with the plum hose and its further replacement improper operation, as a result of which frequent twisting occur. Because of this, integrity is violated, microcracks appear.

  • mechanical damage to the hose;
  • Clamping of the lumen with solid microparticles;
  • stretching during operation;
  • short length that does not allow to make normal drain into the sewer;
  • Violation of the tightness and density of fastening to the drain tank.

Replacing the hose of the dishwasher Ariston

One of the services of our center is to restore the integrity of the hose of the dishwasher or increase their length to ensure the possibility of moving the device to another place. Our master will perform all the necessary work at home, riding you from the need to contact the workshop yourself.

HotPoint-Ariston technology service program

We provide a guarantee for work and details

The presence of a warranty coupon protects HotPoint-Ariston technology owners from malfunctions with subsequent operation. The intercity warranty is issued for repaired or installed components, as well as for the work center performed by the masters. Owners can count on warranty service even if a new breakdown is not related to previously restored nodes.

During the repair, our masters use only original details that are available in stock. Clients do not have to wait, and repair is possible in a short time. Even serious problems are eliminated as quickly as possible, and the quality of details allows the technique to last many years.

HotPoint-ASTON is free diagnosis is free

Before starting repair, the engineer is diagnosed using modern equipment and tools. It allows you to identify the causes of malfunctions and choose options for their elimination. The terms of repair work, as well as the cost of our services are determined by the results of the diagnosis.

With complex breakdowns, the equipment is delivered to the workshop, where electronic components, power units and important components are replaced. For the convenience of customers, we will organize transportation, which is carried out within 2 hours after the application is executed.

With typical breakdowns that do not require transportation to the service center, repairs are carried out quickly. within 24 hours from the date of detection of a malfunction. A competent approach to business, qualifications of masters and modern equipment allow us to eliminate problems in the shortest possible time.

Get advice from HotPoint-Ariston specialists on repair and maintenance of equipment.

By pressing the “Send” button, you confirm your age and agree to process personal data in accordance with the conditions.

By clicking on the “Send” button, you confirm your majority and agree to process personal data in accordance with the conditions.

Replacing the hose in the dishwasher

Replacing the hose of Ariston dishwasher is one of the services of our company. It is relevant if necessary to restore the hose connection, increase its length due to the new segment. The hose can be damaged mechanically, although the reason for its replacement may be a poor mount.

To do everything right, you need to contact the professionals of the company. They know about all the nuances of such repairs and guarantee the efficiency. Experts will perform diagnostics, after which they will coordinate further Ariston repair actions and its cost with the client.

Experts will cope with the task perfectly. Our services are available to everyone, and promotions, special offers make cooperation more profitable. Call the office now or leave a request on the site, and within an hour our master will arrive in place. He has all the necessary knowledge and practical skills to quickly find damage to the hose and restore its integrity. The company provides a guarantee for repairs, replaced parts, because I am sure of the quality of. We are waiting for calls for consultation, placing an order for calling a master for repair.

How to lengthen the hoses of a dishwasher

If there is a need to lengthen the sleeve in connection with the change of position of the dishwasher or for another reason, then you must have an idea of ​​its technical characteristics, calculate the length for which it is required to increase, diameter, purchase a pouring or drain sleeve of the desired parameters. For work, you still need a connecting coupling and three clamps. For reliability, it is better to apply a brass coupling, not a plastic.

Lengthening the water supply hose

All communications and food on the dishwasher are disconnected. The filling sleeve, which goes from the dishwasher, is attached first to one side of the coupling, the extension cord of the hose, which is connected to the water supply line, is screwed onto the second side of the coupling. It is advisable to change all worn elastic bands, smear the attachment sites with an anti.corrosion solution, check the operation of the hose.

Lengthening of the drain hose

There are no difficulties in lengthening the drain hose on the dishwasher. After its preparation, measurements, you need to purchase a sleeve. the connector of the desired length. In simple movements, connect the old hose to the new. Conducting such manipulations, you can lengthen the drain hose to large sizes. Mechanics, specialists engaged in the repair of dishwashers, advise not to lengthen the hose on the supply of water, especially in several places, but change it, since the risk of water leaks is still present.

Cleaning hoses from blockage

During operation, sometimes problems arise with the flow or drain of water. In this case, it is important to check the sleeves for water leaks or try to clean the hose from the blockage. In the latter case, men will have to take tools and work a little.

First you need to turn off the dishwasher from communications and de.energize. Disconnect the required sleeve, proceed to clean it with a ruff. In the case of severe pollution, the hose can be soaked in a solution of weak acid or alkali, then again use a brush. It is advisable to remove all pollution from the inner surface to reduce the likelihood of leaks in the future. After cleaning, you can set the hose to the place. If after cleansing the problem with the entry. the drain of water remains, the sleeve is required to replace the sleeve.

It turned out that replacing the hoses with a dishwasher is not so difficult, as it seems at first glance, the main thing is true and in accordance with the characteristics to choose all components for this. It is important to check in a timely manner on the “dishwasher” of the supply line and diving of water for serviceability.

All household appliances are not eternal, all devices have a certain service life, at the end of which they may fail. To extend their life, it is necessary to care for correctly and timely, observe all the parameters recommended by the factory. the manufacturer.

How to install it correctly

If in the dishwasher Siemens, Ariston there are problems with a fence or draining of water, the hoses are first checked. If they leak, a complete replacement is required. It is not recommended to repair and seal damage. this is unreliable and eventually lead to a serious leak.

Prepare the dishwasher. Built.in technique “Electrolux”, “Ariston“, “Bosch” take out of the niche. Cross the water supply and disconnect from the network. Most often, the pouring element is connected from behind to the lower part of the case:

To correctly execute a water supply connection, wind up a brass tee with a locking valve to the pipe output. To one conclusion of the tee, connect the sink mixer, to another, a flowing filter and the end of the pouring hose. The connecting parts are sealed with fum tone.

In some models, the dishwasher is the connection inside the case.

  • Turn the body over the back.
  • Remove the lower bar.
  • Unscrew the bolts and remove the pallet.
  • The end of the hose is attached to the flood valve.
  • Using an obstacle key, unscrew the old device and connect the new.

If you need to shorten the length, we do not recommend doing it yourself. It is better to go to the store and purchase an element of the right size.

To increase the length, you will need a special coupling. It is better to choose not plastic, but a brass coupling. Connect it to the main hose, and at the other end, put the extension cord. Connect the device to the water supply, and everything is done.

Experts do not recommend lengthening, as this increases the risk of leaks.

How to replace a plum hose? First you need to check for what reasons he stopped performing his function. Perhaps the case is in the blockage and it is enough to clean it. It can connect in different places: from the bottom right or left, from above. To clean or change the element, do this:

  • With the help of nippers, unfasten the plastic clamps.
  • Turn the technique on the side.
  • Unscrew the screws and remove the lower pallet. In the models “Bosch” or “Gorenje” a float sensor is attached to it. Therefore, before turn off the wiring chip and remove the sensor.
  • Loosen the clamp and remove the end from the seat in the assembly of the circulation pump. Be careful, water can pour from it.

Perhaps replacement and will not be needed, just clean the input hole. To do this, use a small brush and strong pressure.

Now you will cope yourself with the replacement and lengthening of the hose of the dishwasher. This video will help you:

How to correctly change the drain hose in the dishwasher

The need to replace the hose of a dishwasher may occur when a marriage, breakdown or rearrangement of equipment to another place is further from communications. Connect a new hose or increase the length of the existing one on your own is completely easy. Consider how this can be done at home.

  • Types of hoses in the dishwasher
  • Preparation for replacement
  • Tools
  • Step.by.step actions to replace the drain hose
  • Catalog of dishwashers with reviews

Independent replacement of the drain hose of the washing machine

Household manufacturers produce many different models of washing machines. They differ among themselves by technical characteristics, capabilities, the presence of additional functions, appearance. Despite these differences, the main task for them is to wash things, which requires a set and drainage of water. Water enters the machine and leaves it with the help of hoses. During the operation of the drain hose of the washing machine, it can be damaged and it will be necessary to replace it. It is not difficult to perform this operation, so you can do it with your own hands, having devoted a little time to this.

Depending on the model of the washing machine, the location and fastening of the drain hose differs. But there are a number of general actions that need to be done regardless of the model.

replacing, plum, hose, dishwasher, hotpoint, ariston

Before starting to replace, you need to disconnect the machine from communications- electrical and water supply.

Preparation for replacement

Replacing the drain hose a slightly more time.consuming process in comparison with the replacement of bulk. To replace the drain, it is necessary to disassemble the washing machine and disconnect it from the pump pump. Depending on the manufacturer of the machine, the hose inside can be laid and fixed in different ways. To make it more convenient to work, you can first dismantle the upper lid of the machine. This is done as follows:

  • Self.tapping screws are unscrewed. they are located on the back wall of the machine;
  • Having twisted the screws, the lid must be moved back so that it leaves the grooves;
  • Remove and set aside the lid to the side.

Further actions are already dependent on a particular brand of technology. There are several common options for access to the drain hose, which in certain manufacturers are similar due to the design features of machine models.

Types of hoses

There are 2 types of hoses: flood and drainage. The fill hose is equipped with a special valve, if it is damaged, then the water supply will not occur. Purpose of the drain. get rid of dirty water after the completion of washing dishes. It happens that the flood has a special design called the hose with the Autostop device. This avoids a sudden leak during a break in the water supply. This is possible to install instead of, for example, a drain hose for Electrolux dishwasher.

When it is necessary to determine which hose it is better to put, then you should pay attention to factors such as:

Too short will be an obstacle for productive operation of the machine. But the maximum size of the drain hose of the dishwasher will form additional barriers for supplying water, increase the chances of blockages. Therefore, the length is better to choose the average.

Most often, hoses are made of plastic. Such details are quite practical and have a low price. A more reliable option will be a rubber mechanism in a metal braid. But the price of such a device will be higher. Depending on the available funds, you can choose a more suitable option.

The quality of the hose should correspond to the characteristics of the PMM. For example, it matters how much water is consumed by a machine. If consumption is up to 5 liters, then a less strong part is suitable, if more than 5 liters, then you should think about a better mechanism.

The main malfunctions and their elimination

If the dishwasher, for example, Electrolux, has stopped working, then often the reason for this lies in problems with the drainage device. The most frequent breakdowns and methods of their elimination are presented in the table below.

Malfunction Signs and methods of elimination
External or internal damage Over time, any material wears out, becomes not so resistant to the constant effect of water. With this problem, it is worth replacing the hose with a new.
Blockage Often, the water quality is quite low, it has a lot of heavy metals, dirt and other particles. At first this does not particularly affect the operation of the device, but in the future it can harm the internal mechanisms of the machine. In this case, it is worthwhile to clean the part.
Incorrect installation If, with the initial installation, the part was installed incorrectly, then after a while this negligence will make itself felt. This can lead to a breakdown, then you will have to install everything again.
Excess of the drain hose If the mechanism is pushed or bent, then the water has nowhere to go. In such a situation, you just need to straighten the detail.

Diagnostics for problems

So that the dishwasher has been working for many years, the diagnosis of the hose should be carried out at least once a month. This is easy to do with various devices (for example, a pressure gauge), but t.to. Not everyone has such devices, then improvised means are often used for diagnosis.

Ariston dishwasher does not start, the indication does not burn

If there is no reaction to the inclusion, and the power indicator does not work, check: check:

Is there an electricity on the network, perhaps it is unscheduled.

Automatic machines for the car. they probably knocked out.

Outlet. Connect another electrical appliance if it does not work, it is broken. If the device connected to the network does not work, and the indicators do not burn, as mentioned above, it is quite possible, a socket is broken. This is a common problem of old houses where wiring cannot withstand the capacities of household appliances and burns out. To check the voltage, a multimeter is used. By the way, there are situations when the outlet is serviceable, but due to a lack of power due to the poor quality of the intra-house wiring, the unit simply does not start.

Network cord and plug. Inspect the elements for damage. If they are, call a specialist to make a replacement. Any diagnosis begins with the network cable. Check the condition of the wire first of all. The integrity of the wire could be violated as a result of the transfer of heavy furniture, in the process of moving the unit. Inside the cable are copper wires, which can easily be damaged when leaning. This is very dangerous, t.to. can cause a short circuit and even a fire. Damaged cable must be changed immediately. To do this, it is advisable to contact specialists.

If everything is normal with the electric component, then there is a hardware or software breakdown. Will have to contact the service center. It is possible that the lock on the door has broken, the power chains inside the unit housing. To check the wiring and elements, you will need a multimeter. Diagnose without special skills and knowledge, and, moreover, eliminating the breakdown is almost unrealistic.

When you need a master?

You need to call an engineer for any serious problems with Ariston dishwasher. If the power supply is in order, and cleaning the filter elements and hoses did not help, call the service center by phone 7 (495) 137-76-30 or leave a request on the website.

Ariston dishwasher turned on, indicators are burning, but the programs do not start

First look at indicators or display. Most modern models are equipped with a self.diagnosis system. If something breaks down, indicators begin to burn in a certain sequence, or an error code arises on the display. The decoding of signals and codes can be viewed in the instructions for the dishwasher.

Why is such a problem at all? It is possible that water does not enter the equipment. Therefore, you need to check if there is water in general in the water supply system. You should also inspect the pouring hose for the presence of excesses and the protection valve from leaks that could work. In the latter case, you will have to completely change the set hose.

Another reason is the input filter. He could clog with rust or a drop if the water water is hard. It needs to be cleaned. If the water is not gained due to a faulty filling valve, call specialists. The part needs to be changed.

Repair of Ariston dishwashers. quickly and efficiently

Our workshop is a certified service center that specializes in maintenance, warranty and post-warranty repair of dishwashers HotPoint-Ariston. We carry out work of any level of complexity as soon as possible and without prejudice to the quality. Services are provided at the house for the customer for convenience. To call an engineer, just call on the phone number indicated on the website or leave an application for an address exit in the form of feedback. In it, indicate the time convenient for visiting and possible causes of malfunctions.

Repair of Ariston dishwashers may be required in such cases:

Our masters are equipped with all the necessary equipment that allows you to quickly find and repair any malfunctions at the initial stage.

The advantages of contacting our SC

Independently carry out repair and restoration work without experience and tools, it is impossible. So you risk only aggravating the problem. If you need to repair Ariston dishwasher quickly and efficiently, it is better to contact us. We guarantee our customers:

  • staff of qualified specialists;
  • the use of ultra.precision equipment to assess the state of the unit;
  • providing free diagnostics before starting work;
  • transparent pricing and fixed value;
  • the use of exclusively original details and consumables to replace failed elements;
  • individual approach in each case;
  • Long warranty periods for all work carried out.

We offer our services for the repair of dishwashers or washing machines not only, but also in Yekaterinburg, St. Petersburg, Chelyabinsk, Nizhny Novgorod and Voronezh.

| Denial of responsibility | Contacts |RSS