The Samsung vacuum cleaner works but does not suck in dust. Mechanical damage to the gadget

The reasons for disconnecting the vacuum cleaner

They began to notice that your vacuum cleaner began to spontaneously disconnect during operation? The reasons for this behavior can be different and most of them, unfortunately, are impossible to eliminate on their own without the help of a qualified specialist. But to know why this is happening, and try to solve the problem yourself will not be superfluous.

The most common cause of spontaneous shutdown of the vacuum cleaner during operation is the overheating of its parts and nodes. This can be caused by various factors.

  • Strong contamination of the input or output filter (they must be regularly cleaned).
  • High temperature in the room where cleaning is done.
  • Clogging of a flexible hose or input.
  • Engine pollution or electronic elements
  • Violation of contact of one of the engine parts.
  • Violation of contact in the power outlet.

What can be done independently

What to do if the vacuum cleaner turned off right during cleaning and does not turn on, or when it does not turn on after storage? First you need to understand what happened. The algorithm of actions (and it must be performed sequentially) will be one for all devices, regardless of the type of vacuumber, whether it be a container, bag or aquafilter.

  • Check the power source. If there is electricity in the apartment in principle, try to include a vacuum cleaner in another outlet. Perhaps the breakdown did not happen to him, but with the outlet.
  • View the cord and plug of power for ruptures, excesses and other defects. The fork should not be melted, visible damage in the connection with the cord or it should not be on it.
  • The next probable problem is the vacuum cleaner. If it is clogged, a protective shutdown may work. Shake the vacuum cleaner or change the bag. View the hose, perhaps it is clogged with large garbage.

If the vacuum cleaner did not come to any of the stages of diagnosis, the matter is in a broken or burned engine. In this case, only masters from the service will help, who will test the device on professional equipment and repair it.

What to do if the vacuum cleaner does not suck? We are looking for the cause of the breakdown

In the lion’s share of cases, the problem is fixable. Five problems and solutions in the table:

Cause What to do
Filled bag Clean reusable, change disposable
Clotted filter Clean it or change it
Damage to the device Change the broken
Blocks in the hose, brushes or tube Check traction without a “suspect” detail. If without it the device works in full force. check for breakdowns and remove “traffic jams”
Broken engine or battery Contact the repairmen

The vacuum cleaner is poorly drawn for one of these reasons. Help of specialists can only be needed when malfunctions. In other cases, a few free minutes and accuracy are enough during operation.

The right choice: which vacuum cleaner is better. wired or wireless: 3 points to “think”

Features of working with aquafilter

In vacuum cleaners with such components there is an additional non.Needle filter, which was mentioned earlier. In devices with such equipment, it is necessary to check more details for the presence of accumulated pollution. The rest of the vacuum cleaner with the aquafilter does not work for the same reasons that were given above. And malfunctions are eliminated by similar algorithms.

We inspect the components

We move further by exclusion and move on to the following possible reason that the vacuum cleaner began to draw poorly. the hose or brush was damaged. As for the hose, it may not be completely inserted into the case or damaged as shown in the photo. Bottom line. the vacuum cleaner does not pull or the thrust is completely weak.

Brushes are checked by the level of pollution. Typically, they remains such garbage as hair and thin ropes. You need to remove all the pollution and check whether the thrust has appeared. You also need to make sure that the bribberry roller rotates freely and does not worry. Perhaps the bearing was just jammed, as a result of which brushes prevent the absorption of air. In general, it should be noted that an uncomfortable nozzle is very often a “culprit” that in the vacuum cleaner the thrust is weak. Typically, buyers of cheap Chinese technology are faced with such a moment.

Also try to clean the hose with a wire, perhaps somewhere inside the garbage interferes with the passage of dust into the bag, which can also be accompanied by the fact that the technique is buzzing or even very noisy, but does not suck the air. You can make sure that the cause of poor traction is a hose by turning it off and checking the quality of absorption by your hand at the exit from the body. If in this case the vacuum cleaner does not suck, only one possible malfunction remains. the motor.

Repair the engine

Well, the last thing that could be is the failure of the engine. This malfunction can be determined by touching the body’s body-it heats up strongly, which means that something is wrong. In addition to the fact that the motor is very hot and overheating, it can still turn off. Do not know what the reason is if the vacuum cleaner does not suck and disconnects?. Why is the craving and what needs to be done for repair!

First you need to remove the decorative protection of the case and use the multimeter to call all sections of the chain. Typically, the technique does not work due to the burning of the fuse. If this is true, replace it with a new one with exactly the same parameters. In the event that there is a break in the winding on one of the coils, it is better to go and choose a new vacuum cleaner, t.to. Buying a motor will be expensive pleasure. In addition, contact on one of the wire connections may simply break. Here the repair will not be difficult, especially if you are “friends” with a soldering iron.

If the problem is that the vacuum cleaner does not pull and turns off due to the engine brushes that you decide to replace, be careful when connecting them. Incorrect connection of brushes can cause a vacuum cleaner after repairing, but blows dust.

That’s all the main causes of malfunctions. Finally, I would like to note that if you have a poorly absorbing a vacuum cleaner with a water filter, you need to act by analogy with ordinary equipment. The only difference is that instead of a vacuumer, you need to wash the aquafilter properly! We hope that now you know what to do with any deterioration of traction or its complete absence!

Search for reasons

Diagnosis always helps to determine the cause of poor absorption of dust. Any person who knows how to use a screwdriver is able to perform the procedure. However, the case may not reach the disassembly of the vacuum cleaner if the breakdown does not apply to the electrical part of the unit.

Often the conduct of surface diagnosis allows you to identify the following causes of poor absorption:

  • During the cleaning, a large item was drawn, and it was stuck inside the hose or telescopic handle;
  • The vacuumber has not been cleaned for a long time and completely clogged with garbage;
  • The filter clogged on the exhaust of the vacuum cleaner;
  • a corrugated hose, a working nozzle or telescopic pen was damaged.

If these causes are not detected during the diagnosis, the problem lies inside the vacuum cleaner. The weakening of the absorption force occurs due to the drop in the power of the electric motor. The cause may be the wear of the brushes, the pollution of the anchor collector, the gearing of the bearings, the formation of thick dust deposits on the fan impeller. Power drop sometimes occurs when the electronic unit fails. As a result, the adjusting wheel is not able to change the engine speed or they begin to “swim”.

To conduct surface diagnostics from the vacuum cleaner disconnect all components. The inspection begins with the working nozzle, then move to the telescopic handle and corrugated hose. There should not be cracks, holes and other defects on components. It is important to check the inner part for the absence of stuck objects.

Further verification is subjected to a vacuum cleaner and a filter on the exhaust of the vacuum cleaner. These two nodes greatly affect the power of absorption. A one.time filter is changed to a new one, and a reusable fabric bag is well lined.

Cyclone vacuum cleaners between the engine and the garbage collector have an additional foam filter. The plate is greatly clogged with dust and it needs to be washed. Another filter is on the exhaust. If it is clogged with dust, the exhausted air receives an obstacle, returns to the fan, reducing the force of absorption.

Ways to solve problems

Diagnosis only helps to find the cause of the vacuum cleaner malfunction. Further actions are aimed at eliminating the breakdown.

Vacuumber

Overflow of vacuumers with garbage is the most common problem of impairment of absorption. For any vacuum cleaner, it is not allowed to fill out the bag or capacity of more than 80%. With an increase in clogging, the craving weakens or completely disappears.

Manufacturers are equipped with expensive models with light indicators of the occupancy of the vacuumor. The green glow of the bulb signals normal work. When the indicator glows red, the vacuum cleaner is full and requires cleaning. Cheap vacuum cleaners do not have such a function. The vacuum cleaner has to be checked after each cleaning.

Eliminate the problem associated with the dirty vacuumber, just. In the cyclone, it is enough to simply throw out the garbage from the container. The one.time paper bag is only thrown away, and a new. The second time a vacuumber cannot be used. After operation and thorough shaking, the paper walls of the bag weaken. The re.installed disposable vacuum cleaner will tear off a strong stream of air, and the dust will tighten into the fan.

The fabric reusable vacuumers of the housewife always only shake. The cleaning method is good, but not effective. A large amount of dust remains between fibers of the fabric, blocking the free passage of air. Fabric bags after several times use in clean water.

The vacuumboard can be innocent if the power regulator is strongly screwed. Sometimes the rotation of the wheel allows you to solve the problem of poor absorption.

Filters of thin cleaning

Polluted vacuumboards pay attention to more often than on thin cleaning filters, and in vain. One of them stands in front of the fan. The cyclones usually be a filter by a foam plate, enclosed inside a plastic collapsible case. Foam rubber is greatly clogged with dust after each cleaning. The plate is thoroughly knocked out and rinked in water. Additionally, the plastic case of the filter on the back has a grid with small cells. It must be washed.

The second thin cleaning filter is on the exhaust of the vacuum cleaner. Usually it is made in the form of a separate box with many cells. The filter prevents the outlets of dust from the vacuum cleaner to the room. Clogged cells are cleaned with a soft brush or rinsed with clean water. Such procedures will be successful a couple of times. After 50 hours of operation, the filter must be replaced.

Components

The components of the vacuum cleaner include a corrugated hose, a telescopic handle, work nozzles. During cleaning, an accidentally drawn large object jams on bends or crossings. You can clean the hose and telescopic handle with a long stick without burrs or soft wire in isolation. The operating channel of the working nozzle is usually curved. Cleaning it is easier for something well bending: wire, cable, elastic PVC rod.

Samsung Station Dust Disposal with Hygienic Cleaning Filter Household-Handheld-vacuums, 2021

On the brush after cleaning, check the wheels. Hair is often wound on them. If the roller is equipped with bearings, they make their lubricant.

Additionally check the joints of all elements. Blaged locks, cracks and other defects create air leaks. The broken hose is immediately replaced. Temporarily rupture eliminates a transitional sleeve. The hose is cut, a piece of a plastic tube is inserted inside, the joints are clamped with clamps and wound with tape.

Electric motor

If the cause of weak traction is the electric part of the vacuum cleaner, the engine begins to work incorrectly. An extraneous noise appears, the body is very hot, the turns are reduced or “swim”.

  • network cable defect;
  • wear of brushes, bearings;
  • pollution of the anchor collector;
  • The failure of the start button or electronic unit.
samsung, vacuum, cleaner, works

It is difficult to find the reason without having basic knowledge about electrical engineering. The electric motor will have to be fully extracted, disassembled and rang all parts by a multimeter. It will be possible to change the brushes, bearings or fuses on an electronic unit on their own. The closure of the windings cannot be eliminated. Have to contact the service or buy a new motor.

There are many reasons for the poor absorption of the vacuum cleaner, and all of them negatively affect the electric motor. At the first signs of decrease in performance, you can not hesitate with the repair.

How to understand what is the cause of heating

There are several reasons why the vacuum cleaner is very warming. This is a malfunction in the engine, filled with dust filter, clogged filter or stuck garbage in the hose. Some of them can be detected and fixed independently, because of others you will have to contact the service center.

The procedure for diagnosing problems

Search for the reason why the vacuum cleaner can heat up when working is recommended by exclusion. It is necessary to take out parts in turn or turn them off, then check the work of equipment without them. You can pull parts only when the device is turned off from the network.

First of all, you need to check the installed settings. Perhaps they went astray, which is why the equipment began to work at higher speed and warm up harder.

The procedure for home diagnostics should be as follows:

  • You need to disconnect the hose and nozzle, then turn on the technique. If the problem has disappeared, probably a small object is stuck in the hose, which interferes with the passage of air.
  • It is worth examining the input hole: it can be clogged with dirt or closed by a thing that has been drawn during cleaning.
  • Then you need to check the vacuum cleaner: pull it out and turn it on the device. If the work has been established, it is necessary to clean the bag or container.
  • Similarly, check the filter: pull it out after turning off the equipment and rinse it.

If nothing helps, and the vacuum cleaner continues to warm, most likely, the reason for the motor work. In order not to damage the technique, it is better not to try to repair it yourself, but to take it to the service center for diagnostics.

The main reasons and their elimination

The reasons why the vacuum cleaner overheats and regularly turns off can be several. Some of them, for example, a stuck item or a crowded vacuumber, can be eliminated independently. Others can only diagnose and fix the master.

samsung, vacuum, cleaner, works

The filter clogged

This is one of the most common reasons why the vacuum cleaner is warming. Modern models are equipped with special filters through which air passes. Filters delay dust, dirt, garbage and other small objects. Over time, the filter cells are clogged, the air passes with difficulty, and overheating occurs.

  • High school graduation. Designed to delay dust and dirt, that is, the main job “lies” on it. It is recommended to clean it after 50 hours of use. If he has never been cleaned over many years of work, a complete replacement may be required.
  • Thin cleaning. It delays the most tiny particles, microorganisms and allergens, is usually located on the rear panel in front of the motor. It is changed as they become dirty.

It happens that the vacuum cleaner is disconnected during operation, the reason lies in the filters. To make sure this is necessary:

  • Turn off the equipment and pull out filters.
  • Turn on the device.
  • If he is well pulled, without any problems, then it is worth washing or replacing filters.

The cleaning of the filter depends on its type: the bag must be replaced, change the water in the aquafilter and rinse the container, is washed with warm water and dry and dry.

The obstacle in the air

The reason for overheating of the engine EL on the Samsung vacuum cleaner and other companies may consist in random absorption of a small item. The latter can get stuck in a hose or input and interfere with air passage.

  • You need to turn off the device.
  • Remove the hose and blow it or clean it using a long object (wire, ruler, mop handle). You can connect it to the output and turn it on all power so that the air flow knocks out an extra item.

Another option for a malfunction is a hole in the hose through which air goes. You can find it by turning on the vacuum cleaner and carefully feeling the duct. The hose is best replaced.

Overflow of a vacuum cleaner

Sometimes to find out why the vacuum cleaner heats up and turns off, what is the reason and how to solve the problem is even easier. just check whether the vacuumber is filled with a vacuum. To make sure that the vacuum cleaner overheated and turned off because of this, you need to pull out a dust collection container and turn it on. If the craving is back, then the problem was found.

Typically, manufacturers indicate in the instructions how often cleaning or replacement is required. On average, the vacuum cleaner should be filled by no more than 80% or replaced after 3-5 siders.

Engine malfunction

If the vacuum cleaner is dusting, heats up quickly and turns off, it makes noise suspiciously strongly and vibrates, the problem can be in the motor. It will be necessary to take it to the service center and wait for a specialist to solve.

A complete replacement of the motor will cost quite expensive. it may be better to replace the technique itself. But do not immediately write off the device. Often a complete replacement of the motor is not needed: it is enough to clean the fan, replace the bearings or other parts.

It happens that the technique initially has weak details, for example, a bad hose. Their replacement for better quality will rectify the situation. When buying, it is worth studying reviews: it is easy to understand what problems to expect from technology. For example, one of the reasons why the Samsung vacuum cleaner is warming up in unsuccessful models. They are always warming up, regardless of the amount of watts and service life.

You need to remember what to do if the vacuum cleaner began to quickly overheat and disconnect during operation. First, you should try to find the reason on your own: check whether the filter is clean, whether something is stuck in the air duct, whether the dust collection is clogged. If the cause is not detected, you will have to contact a specialist.

Why the vacuum cleaner turned off during operation and stopped turning on

Making a bag of fabric to a vacuum cleaner with your own hands

The vacuum cleaner works, but stops absorbing dust. why is it happening

Creating a cyclone for a vacuum cleaner. schemes for construction and household

How a vacuum cleaner works and what you can do with it

Industrial vacuum cleaners for cleaning industrial premises

Filling a dust bag

The frequently caused breakdown is the filling of a dust bag. Most modern vacuum cleaners suggest the presence of an indicator on the dashboard showing the degree of fullness of the bag. The device itself will inform you when it will be necessary to change or clean the vacuum cleaner.

Some units are not yet equipped with such a convenient technology, so to determine the degree of loading of the bag you will need to look into it. If 70 % of the space is filled with dust and garbage, traction can significantly weaken or completely abuse. This can serve as a signal to its replacement. It is worth yielding to the desire to save money and not wait for the moment when the vacuumber will be filled with garbage to the stop.

There are 2 options for further development of events. If the vacuumber is made of paper, it should be removed, thrown away and replaced with new. With a bag of fabric, the situation is somewhat different. Such an accessory is reusable, in connection with which it is not worth throwing it. It is necessary to shake its contents well into the garbage bag, wash the bag in clean water without adding powder and soap, dry and insert into a vacuum cleaner. You can limit yourself to shaking and installation procedures back, but in this case the remaining dust can get into the device. If the problem of poor absorption was not in filling out the bag, you must go to the next step.

Filter pollution and breakdown of components of elements

There are 2 filters in the vacuum cleaner that can lead to a decrease in the absorption power when contaminating. These include:

The first is in front of the engine. Most often it is located on the back of the device. It should be regularly cleaned. To do this, you just need to remove the filter and rinse under warm running water. If the vacuum cleaner continues to perform its work poorly, replace this element with a new. The exhaust filter should be changed after 50 hours of intensive work. If it has not been replaced in continuation of a long time, it should definitely be performed, since the cause of the malfunction will hide in its clogging.

What to do if the vacuum cleaner does not suck well, and the dust bag and pure filters? You should check all the elements of the device. You need to start with a hose. It is necessary to inspect how tightly it is attached to the input hole. It is worth taking a thin metal wire and check if the pipe is clogged. Next, you need to check the degree of cleanliness of the brushes. They should always be sufficiently clean. Remove dirt, garbage and hair from them after each cleaning, and not only when there are problems with the operation of the device.

It is also worth lubricating the bearings with machine oil, as they can cause poor absorption during the operation of the vacuum cleaner

Why does the vacuum cleaner suck poorly and what to do

Often during operation there is a picture that the vacuum cleaner does not suck well dust. To understand the cause of the breakdown, it is necessary to initially conduct the initial diagnosis of household appliances and identify the malfunction.

The vacuum cleaner is poorly sucking garbage, and this fact makes people contact the service for repair. However, there are times when household appliances can be fixed on your own. To do this, you only have to clarify the cause of the malfunction.

The vacuum cleaner is clogged

If the vacuum cleaner has become difficult to absorb garbage, then there is a reason to fill the bag.

You can eliminate the malfunction with the following methods:

modern and expensive vacuum cleaners are equipped with light indicators of the vacuumer. Lights burning with green light notify that you can work, and the red glow warns that the bag is filled.

Important! Filling a vacuum cleaner is not allowed more than 2/3 of the capacity. It should be remembered that with a clean bag a household device works better.

The hose, tube or brush clogged

When cleaning the room, various objects or woolen fibers that clog the duct often come across in the brush. For this reason, the vacuum cleaner began to suck poorly. Here it is only necessary to clean the nozzles and other components from third.party garbage.

If a rumble appears, then this is a sign of hose blockage. Accumulated garbage can be removed with a metal wire.

Unscrew the hose and clean the garbage with a metal cable

Filters are clogged

Filter clogging is another reason for reducing the power of household appliances. It depends on the degree of wear and material of components.

If the vacuum cleaner is new, then the filters can be cleaned, in the case of prolonged operation of the household appliance, you will need to buy and install new components.

Corrugated hose

A malfunction in the form of breakdowns of components is another reason for poor absorption of dust. The appearance of mechanical damage leads to depressurization, and therefore there is a decrease in power.

You can eliminate the problem on your own using the island. She needs to wrap the place of crack. But this solution is short.lived, it is better to purchase a new hose.

Engine breakdown

When touching the body of the device, it feels that it heats up. If the unpleasant smell of Gary spreads, then this indicates an accuracy of the motor breakdown.

The described fault arises due to the following factors:

  • damaged network cable;
  • the life of the brushes and bearings came out;
  • The dirt fell into the collector of the anchor;
  • damage appeared in the electronic unit;
  • The fuse has burned out.

If the case is warming up, then this may be a break in the winding. In this case, experts advise buying a new vacuum cleaner.

It is necessary to disassemble household appliances and diagnose

Important! When there are no special skills in the assembly of electric motors, it is better to contact the service for malfunctioning a malfunction in the motor.

Wear of the brushes or a break in the heat.guide

The vacuum cleaner is badly pulling if the brush is out of order. Any mechanical damage on the nozzle will prevent powerful garbage absorption. Here it remains only to purchase a new brush.

When replacing thermal subjects, they acquire the same sample.

What to do

Reducing power mainly depends on the same causes. In order to avoid malfunctions, you should adhere to several nuances during the operation of the vacuum cleaner:

  • avoid the bending of the hose in the work;
  • Do not vacuum construction garbage;
  • clean or change filters every six months;
  • timely clean the vacuum cleaner;
  • In case of overheating of the case without certain knowledge, do not repair it yourself, but contact the service.

Samsung vs70. How To Empty The Dust Container And Clean The Filters

Subject to these simple truths with a vacuum cleaner, you can put things in order in the room for a long time.

If the vacuum cleaner reduced the power for absorption, then this is not a reason to contact him at the service center. Many problems are solved in affordable ways, most importantly, follow the instructions.

Filter pollution and breakdown of components of elements

There are 2 filters in the vacuum cleaner that can lead to a decrease in the absorption power when contaminating. These include:

samsung, vacuum, cleaner, works

The first is in front of the engine. Most often it is located on the back of the device. It should be regularly cleaned. To do this, you just need to remove the filter and rinse under warm running water. If the vacuum cleaner continues to perform its work poorly, replace this element with a new. The exhaust filter should be changed after 50 hours of intensive work. If it has not been replaced in continuation of a long time, it should definitely be performed, since the cause of the malfunction will hide in its clogging.

What to do if the vacuum cleaner does not suck well, and the dust bag and pure filters? You should check all the elements of the device. You need to start with a hose. It is necessary to inspect how tightly it is attached to the input hole. It is worth taking a thin metal wire and check if the pipe is clogged. Next, you need to check the degree of cleanliness of the brushes. They should always be sufficiently clean. Remove dirt, garbage and hair from them after each cleaning, and not only when there are problems with the operation of the device.

It is also worth lubricating the bearings with machine oil, as they can cause poor absorption during the operation of the vacuum cleaner

Filters clogged

There are two filters in the vacuum cleaner: pre.trial (installed in front of the electric motor) and exhaust (installed after the electric motor). If any of them is clogged, the absorption power falls.

On different models, filters look different and are in different places. Detailed information about them is given in the user’s instructions.

For example, this is what the pre.engineer filter of the vacuum cleaner Samsung SD9480 looks

For example, this is what the exhaust filter of the vacuum cleaner Samsung SD9480 looks like

Remove the prefabrical filter from the vacuum cleaner and turn it on. Check the force of absorption with your hand. In no case do not vacuum without a filter.

If the absorption force without a pre.engine filter has increased, clean the filter and install it back. Check the force of absorption again.

If the absorption force after installing the filter has not changed, then everything is in order with the vacuum cleaner, use further.

If the absorption force after installing the filter decreased, then the filter has become unusable. Buy a new filter.

If the absorption force without a pre.trial filter has not changed, remove the exhaust filter from the vacuum cleaner. Check the force of absorption with your hand without two filters. In no case do not vacuum without filters. If the absorption force without filters has increased, clean both filters and install them back. Check the force of absorption again.

If the absorption force after installing the filters has not changed, then everything is in order with the vacuum cleaner, use further.

If the absorption force after installing the filters decreased, then the filters have become unusable. Get new filters.

Wear of graphite brushes or a break in the heat.subject

If you checked everything, and the vacuum cleaner still does not suck and works weakly, you will have to go to the engine examination. Frequent cause of breakdown. wear of brushes from graphite. Their function is to transfer the current to the engine. ), but only a person who has certain skills can change them on their own.

In addition to the condition of the brushes, check the fuse of the fuse and replace it if necessary. In the presence of experience, you can independently make a “call” of the engine circuit using a multimeter and replace the fuse. Many fuses are equipped with a melting with plastic insert, which fails with regular heating of the electrical appliance.

In the absence of skills in handling equipment, give the electrical appliance to the specialist of the service center.

Motor exice

Когда пылесос плохо тянет и начинает сильно «греться» — вероятно, причина в поломке двигателя. Usually, he “warms up” gradually, but in this case this happens immediately after its connection to the outlet. If the device provides a fuse, it will spontaneously turn off when overheating.

The worst sceno of events is a break in the engine stator. If the fuse can be changed, then in the case of a stator break, nothing can be done. The coil winding cannot be restored, so it is better to take care of buying a new vacuum cleaner right away.

In case of malfunctions in the vacuum cleaner, many problems can be eliminated independently, but if the engine has failed, it is better to contact a professional master.

| Denial of responsibility | Contacts |RSS