What to do if your dyson vacuum cleaner breaks

Why has the vacuum cleaner stopped working and will not start again?

It often happens that the vacuum cleaner stopped turning on and does not work right in the middle of cleaning. often than not, you can find and fix the problem yourself: change the dust bag and filter, check the hose. serious versions are better left to professionals from the service center. To increase the life of the equipment, you need to follow some rules of operation and conduct regular inspections.

When you can fix it yourself?

As a rule, to spoil the design is quite difficult, because this company produces vacuum cleaners from very durable materials, resistant to damage. Some minor problems can therefore be repaired yourself, without fear of damaging the vacuum cleaner. For example, if the dust suction capacity decreases, it is enough to try to clean the dust canister, suction nozzles and to wash the micro filter.

Motor overheating can also occur because the dust canister is too clogged or dirt gets into the motor part. Odors are eliminated by cleaning the micro filter and the telescopic tube. There are simple recommendations that will allow you to control the level of contamination of the vacuum cleaner:

  • The dust canister must be cleaned and changed regularly;
  • Replace the micro filter every 3 months;
  • Use the vacuum cleaner only for its intended purpose (for example, not to pick up liquids, if the device is only meant to pick up dry dust).

Basic assemblies in which problems may arise

Dyson vacuum cleaners are considered quite reliable, but even they can have problems. Most often the latter are expressed in the form of loss of power, overheating, shutdown during operation and extraneous noises.

Some, the most common problems can be solved by yourself in a few minutes. The most “vulnerable” parts include:

  • Dust collector. If it’s full of debris, there’s no place for dirt to stay, and the air doesn’t flow properly, so the motor overheats. To solve the issue, you can regularly clean the filter or replace it.
  • Filters. They collect all particles, microorganisms and allergens. It is important to change them regularly, otherwise dirt will get into the engine.
  • Nozzles. In the process of cleaning, they constantly get dirty and clogged with dust and pet hair. It needs to be cleaned on a regular basis.
  • Hose. It’s worth checking if there’s a suggestion that something is stuck inside.
See also  What does the robot vacuum cleaner Mamibot says

Pay attention! To make sure that the problem is a specific part, after removing each one, you need to turn on the vacuum cleaner and see if it works.

In which cases you can fix it yourself

Self-cleaning and disassembly Dyson vacuum cleaner possible only if it concerns the nozzle, hose, filter, dust collector. that is, parts of the device that can be removed, replaced and inserted back. It is better to have the motor repaired by a specialist, as a complete replacement in case of a serious breakdown may exceed the price of a new unit.

Note! Power cord repair is also best left to a professional. A faulty repair can cause the motor to short out and burn out.

Step 9

Disassemble the cyclone assembly by pulling the two parts apart. Note that these parts may be glued together, so you may need to use some force. You can now remove the gasket between the parts.

When reassembling, note that you must squeeze the two parts very hard until you hear/feel a click.

Fix a typical defect in 24 hours!

In these and many other cases, contact a Dyson service center professional immediately and do not try to repair this or that breakage yourself. Why you should choose us?

your, dyson, vacuum, cleaner
  • We minimize dyson vacuum cleaner repair time, thanks to the availability of original spare parts and the high professionalism of our employees, who know Dyson vacuum cleaners like the back of their hand.
  • Guarantee quality work, as evidenced by the officially provided warranty.
  • We carry out free diagnostics and offer free delivery of equipment, reducing your time and finances.
  • We have a staff of experienced craftsmen with impressive experience and technical education.
  • You will be happy with the prices.

All company names and trademarks are the property of their respective owners and are used on this site for information purposes only. Information on this site is not a public offer. The site is for information purposes only and may contain errors. The final cost of repair can be determined only as a result of diagnostics.

See also  Xiaomi app to control the robot vacuum cleaner

How to disassemble the device?

Under the filters of different degrees of purity hides a fan, whose blade is covered and located between a pair of metal plates. This creates closed channels. The motor is located under a plastic (usually white) casing with an air-flow shutoff.

Before proceeding with the repair, the vacuum cleaner, of course, must be unplugged, and then proceed to remove the housing. Filters that close access to the motor are removed, the plastic part of the housing is unscrewed and removed. The motor is pulled out of the casing, then the fan is screwed on (very carefully, the nut has a left-hand thread), then you can find the cover, under which the electrical part is.

There are vacuum cleaners with two motors. The second is usually in the area of the brush and can affect the degree of suction of dust or liquid. Reassemble the vacuum cleaner in the same way, but in reverse order.

To begin with

Before picking up the screwdriver and disassembling the vacuum cleaner, troubleshoot three common problems:

Check to see if the dust bag is clogged

If the bag is filled with more than two-thirds of the debris, the suction power wanes, it feels like it “doesn’t pull”.

The paper dust bag needs to be replaced with a new one, and the cloth bag needs to be shaken out, washed in water, and dried.

Make sure hose, tube or brush is not clogged

If the bag is okay and there is still no traction, check the other accessories. the brushes, telescopic tube and hose. The hose may be damaged, cracked, pierced, clogged or not fully seated in its housing.

Both small particles and large objects get stuck in the brushes, hose and tube: string, tissues, handkerchiefs, rags, etc.

How to properly clean a Dyson DC59 head and fix one that’s not rotating (V6 and V7 too)

These are causing the dirt to leak poorly, the vacuum cleaner is humming, howling, whirring or making other inadequately loud noises, reeking of burning or something else burnt. Usually after the clog is removed, the draught is completely restored.

Also check the accessories for wear and tear: in some cases, jammed motor bearings or even improperly seated brushes can make suction difficult.

Looking for cracks in the corrugated hose

Cracked hose creates air suction and prevents the creation of suction to draw in the debris.

See also  How to make a fireplace screensaver on your TV

We recommend to change such hose completely, but there is also temporary solution. to insert inside the adapter sleeve.

your, dyson, vacuum, cleaner

To do this, cut the tube, insert a piece of plastic tube inside, clamp its joints with clamps and seal the cut with tape.

Clean filters

It is a big mistake to inspect the dust collector, but do not check the cleaning filters: after each cleaning, the elements are heavily filled with dust.

Can You Kill a Dyson Vacuum Cleaner?

One of the filters is located in front of the fan. Cyclones usually have a foam plate inside a collapsible plastic bowl. There is a fine mesh strainer on the back of the body. The plate should be well knocked out and washed in water together with the filter.

The second, rear fine filter is installed on the exhaust of the vacuum cleaner. Most often it is a separate box with a large number of cells. The cells should be cleaned with a soft brush and rinsed under running water.

If the vacuum cleaner has a water filter, do not forget to clean it after each cleaning: disassemble, rinse each element and thoroughly dry. It is necessary to do this, even if there are no problems with the vacuum cleaner, so that bacteria and fungi do not breed in the dirty water.

Check to see if you overheated the appliance

If your vacuum gets too hot, the electronics can shut down the motor on their own. It is enough to wait 20-30 minutes to restore performance.

your, dyson, vacuum, cleaner

Overheating can be caused not only by prolonged operation. there are other reasons:

  • heated because the mains cable is damaged;
  • the armature collector is clogged;
  • the bearings and brushes are worn out;
  • The electronic block or start button is defective.

The most serious malfunction of a vacuum cleaner is a broken motor. To detect it, you will have to disassemble the device.

What exactly can be done by yourself

And you can also buy a robot vacuum cleaner: they work on batteries with a voltage not higher than 15 V, so their motor is unlikely to overheat. Robot repair is much easier. Examples of brands. Iclebo Arte and iLife.

| Denial of responsibility | Contacts |RSS